6-Speed Direct Shift Gearbox (DSG/02E): Difference between revisions

← Older edit Newer edit →

Revision as of 20:44, 29 November 2006

Basic Setting

NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.

[Select]
[02 - Transmission]
[Basic Settings - 04]

Transmission Tolerances (Enganged Calibration)

Block 061
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Transmission Tolerances (Synch. Point. Measurement)

Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Clutch Adaptation

Control Module Software Version < 0800:

Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Control Module Software Version >= 0800 :

Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Clutch Safety Function)

Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Pressure Adaptation)

Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (Steering Wheel Paddle Installation)

Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

Reset Values (ESP & Tip Cruise Control)

Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

[Done, Go Back]
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.

Special Procedures

Defined Test Drive

Suggested test drive after replacing the mechatronic or successful basic setting.

Prerequisites:

ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.

Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check).
Evaluate creep and starting-off points.
Check for leaks.

NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.

@@ Line 1: / Line 1: @@
 == Basic Setting ==
-'''''NOTE:''' Make sure to perform the following steps in a row followed by the defined test drive.''
+'''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed  by the defined test drive.''
 '''[Select]'''<br>
@@ Line 16: / Line 16: @@
 === Transmission Tolerances (Synch. Point. Measurement) ===
-Block 060<br>
+Group 060<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 25: / Line 25: @@
 '''''Control Module Software Version < 0800:'''''
-Block 062<br>
+Group 062<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 32: / Line 32: @@
 '''''Control Module Software Version >= 0800 :'''''
-Block 067<br>
+Group 067<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 39: / Line 39: @@
 === Reset Values (Clutch Safety Function) ===
-Block 068<br>
+Group 068<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 46: / Line 46: @@
 === Reset Values (Pressure Adaptation) ===
-Block 065<br>
+Group 065<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 53: / Line 53: @@
 === Reset Values (Steering Wheel Paddle Installation) ===
-Block 063<br>
+Group 063<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 60: / Line 60: @@
 === Reset Values (ESP & Tip Cruise Control) ===
-Block 069<br>
+Group 069<br>
 '''[Go!]'''<br>
 Activate the Basic Setting.<br>
@@ Line 76: / Line 76: @@
 ''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br>
 '''<u>Prerequisites:</u>'''<br>
-* ATF Temperature 30...100 °C (86...210 °F), see MVB 019.
+* ATF Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.
@@ Line 83: / Line 83: @@
 The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br>
 Perform one sharp braking followed by a full throttle acceleration (oil return check).<br>
-Drive with avaluation of crawling and starting-off points.<br>
+Evaluate creep and starting-off points.<br>
 Check for leaks.<br>
-'''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, the remaining quick adaptations are performed automatically in the following driving cycles.''
+'''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, any remaining  adaptations will be performed automatically during normal driving.''
 [[Category:Transmissions]]