Difference between revisions of "Audi A6 (4F) Parking Brake"
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
== Coding == | == Coding == | ||
| + | |||
| + | '''''Note''': When replacing this Control Module you do need to perform the Basic Settings (MVB 010 & 020) first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!''<br> | ||
| + | |||
*'''000??xx''': ''Engine'' | *'''000??xx''': ''Engine'' | ||
**01 = 2.0l TDI (Diesel) | **01 = 2.0l TDI (Diesel) | ||
| Line 60: | Line 63: | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
| − | The brake pads will then now opening and close 3 times.<br> | + | The brake pads will then now opening and close 3 times, make sure the parking brake is opened before performing this basic setting.<br> |
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | |||
| + | === Inclination Angle Sensor Calibration === | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[53 - Parking Brake]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 020<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | Make sure to have the car on an even surface and do not move/rock it.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
Revision as of 17:21, 11 July 2007
Coding
Note: When replacing this Control Module you do need to perform the Basic Settings (MVB 010 & 020) first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!
- 000??xx: Engine
- 01 = 2.0l TDI (Diesel)
- 03 = 3.0l TDI (Diesel)
- 05 = 2.7l TDI (Diesel)
- 10 = 2.0l TFSI (Gasoline)
- 20 = 2.4l MPI (Gasoline)
- 30 = 2.8l FSI (Gasoline)
- 40 = 3.0l MPI (Gasoline)
- 50 = 3.2l FSI (Gasoline)
- 60 = 4.2l MPI (Gasoline)
- 70 = 4.2l FSI (Gasoline)
- 000xx?x: Transmission
- 1 = Manual Transmission
- 2 = Automatic Transmission (09L/09E)
- 3 = Multitronic (01J)
- 000xxx?: Country
- 1 = Rest of World (RoW)
- 2 = USA/Canada
- 3 = Japan
Basic Setting
Open Rear Parking Brake
Cycle the Parking Brake ON, then OFF first.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
The brake calipers will then open, allowing the pads to be changed.
[Done, Go Back]
[Close Controller, Go Back - 06]
It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point.
Close Rear Parking Brake
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
The brake calipers will then close.
[Done, Go Back]
[Close Controller, Go Back - 06]
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly. This should stop after cycling the Parking Brake ON, then OFF again.
Function Test
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads will then now opening and close 3 times, make sure the parking brake is opened before performing this basic setting.
[Done, Go Back]
[Close Controller, Go Back - 06]
Inclination Angle Sensor Calibration
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Make sure to have the car on an even surface and do not move/rock it.
[Done, Go Back]
[Close Controller, Go Back - 06]