Difference between revisions of "Audi A6 (4F) Parking Brake"

From Ross-Tech Wiki
m
m
Line 2: Line 2:
 
== Coding ==
 
== Coding ==
  
'''''Note''': When replacing this Control Module you do need to perform the Basic Settings (MVB 010 & 020) first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!''<br>
+
'''''Note''': When replacing this Control Module you do need to perform the Basic Settings [[#Function Test|Function Test (MVB 010)]] and [[#Inclination Angle Sensor Calibration|Inclination Angle Sensor Calibration (MVB 020)]] first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!''<br>
  
 
*'''000??xx''': ''Engine''
 
*'''000??xx''': ''Engine''

Revision as of 18:23, 11 July 2007

Coding

Note: When replacing this Control Module you do need to perform the Basic Settings Function Test (MVB 010) and Inclination Angle Sensor Calibration (MVB 020) first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!

  • 000??xx: Engine
    • 01 = 2.0l TDI (Diesel)
    • 03 = 3.0l TDI (Diesel)
    • 05 = 2.7l TDI (Diesel)
    • 10 = 2.0l TFSI (Gasoline)
    • 20 = 2.4l MPI (Gasoline)
    • 30 = 2.8l FSI (Gasoline)
    • 40 = 3.0l MPI (Gasoline)
    • 50 = 3.2l FSI (Gasoline)
    • 60 = 4.2l MPI (Gasoline)
    • 70 = 4.2l FSI (Gasoline)
  • 000xx?x: Transmission
    • 1 = Manual Transmission
    • 2 = Automatic Transmission (09L/09E)
    • 3 = Multitronic (01J)
  • 000xxx?: Country
    • 1 = Rest of World (RoW)
    • 2 = USA/Canada
    • 3 = Japan


Basic Setting

Open Rear Parking Brake

Cycle the Parking Brake ON, then OFF first.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
The brake calipers will then open, allowing the pads to be changed.
[Done, Go Back]
[Close Controller, Go Back - 06]
It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point.


Close Rear Parking Brake

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
The brake calipers will then close.
[Done, Go Back]
[Close Controller, Go Back - 06]
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly. This should stop after cycling the Parking Brake ON, then OFF again.


Function Test

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads will then now opening and close 3 times, make sure the parking brake is opened before performing this basic setting.
[Done, Go Back]
[Close Controller, Go Back - 06]


Inclination Angle Sensor Calibration

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Make sure to have the car on an even surface and do not move/rock it.
[Done, Go Back]
[Close Controller, Go Back - 06]


Special Procedures