Difference between revisions of "Audi A6 (4F) Parking Brake"
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| Line 2: | Line 2: | ||
== Coding == | == Coding == | ||
| − | '''''Note''': When replacing this Control Module you do need to perform the Basic Settings [[#Function Test|Function Test (MVB 010)]] and [[# | + | '''''Note''': When replacing this Control Module you do need to perform the Basic Settings [[#Function Test|Function Test (MVB 010)]] and [[#Longitudinal Acceleration Sensor (G251)|Longitudinal Acceleration Sensor (MVB 020)]] first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!''<br> |
*'''000??xx''': ''Engine'' | *'''000??xx''': ''Engine'' | ||
| Line 27: | Line 27: | ||
== Basic Setting == | == Basic Setting == | ||
=== Open Rear Parking Brake === | === Open Rear Parking Brake === | ||
| − | + | '''<u>Prerequisites:</u>'''<br> | |
| − | Cycle the Parking Brake ON, then OFF first. | + | * Connect a battery charger. |
| − | + | * Cycle the Parking Brake ON, then OFF first. | |
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[53 - Parking Brake]'''<br> | '''[53 - Parking Brake]'''<br> | ||
| Line 35: | Line 35: | ||
Group 007<br> | Group 007<br> | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
The brake calipers will then open, allowing the pads to be changed.<br> | The brake calipers will then open, allowing the pads to be changed.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | '''[Close Controller, Go Back - 06]'''<br> | + | '''[Close Controller, Go Back - 06]'''<br><br> |
It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point. | It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point. | ||
=== Close Rear Parking Brake === | === Close Rear Parking Brake === | ||
| − | + | '''<u>Prerequisites:</u>'''<br> | |
| + | * Connect a battery charger. | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[53 - Parking Brake]'''<br> | '''[53 - Parking Brake]'''<br> | ||
| Line 48: | Line 51: | ||
Group 006<br> | Group 006<br> | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
The brake calipers will then close.<br> | The brake calipers will then close.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | '''[Close Controller, Go Back - 06]'''<br> | + | '''[Close Controller, Go Back - 06]'''<br><br> |
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly. This should stop after cycling the Parking Brake ON, then OFF again. | The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly. This should stop after cycling the Parking Brake ON, then OFF again. | ||
=== Function Test === | === Function Test === | ||
| − | + | '''<u>Prerequisites:</u>'''<br> | |
| + | * Cycle the Parking Brake ON, then OFF first. | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[53 - Parking Brake]'''<br> | '''[53 - Parking Brake]'''<br> | ||
| Line 63: | Line 69: | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
| − | The brake pads | + | The brake pads are now opening and closing 3 times.<br> |
| + | '''''Important''''': Wait 30 seconds after the brakes stop moving before carrying out the next step.<br> | ||
| + | Due to a firmware problem in some modules, failure to wait can result in damage to the control module.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | '''[Close Controller, Go Back - 06]'''<br> | + | '''[Close Controller, Go Back - 06]'''<br><br> |
| + | |||
| + | === Longitudinal Acceleration Sensor (G251) === | ||
| − | + | '''<u>Prerequisites:</u>'''<br> | |
| + | * System voltage at least 12.0 V. | ||
| + | * Do NOT move/rock car while performing basic setting. | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| Line 77: | Line 89: | ||
Activate the Basic Setting.<br> | Activate the Basic Setting.<br> | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
| − | + | The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.<br> | |
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | |||
Revision as of 21:08, 11 July 2007
Coding
Note: When replacing this Control Module you do need to perform the Basic Settings Function Test (MVB 010) and Longitudinal Acceleration Sensor (MVB 020) first. This sets a Readiness Bit for each of the Basic Settings, the Coding will not be accepted without this!
- 000??xx: Engine
- 01 = 2.0l TDI (Diesel)
- 03 = 3.0l TDI (Diesel)
- 05 = 2.7l TDI (Diesel)
- 10 = 2.0l TFSI (Gasoline)
- 20 = 2.4l MPI (Gasoline)
- 30 = 2.8l FSI (Gasoline)
- 40 = 3.0l MPI (Gasoline)
- 50 = 3.2l FSI (Gasoline)
- 60 = 4.2l MPI (Gasoline)
- 70 = 4.2l FSI (Gasoline)
- 000xx?x: Transmission
- 1 = Manual Transmission
- 2 = Automatic Transmission (09L/09E)
- 3 = Multitronic (01J)
- 000xxx?: Country
- 1 = Rest of World (RoW)
- 2 = USA/Canada
- 3 = Japan
Basic Setting
Open Rear Parking Brake
Prerequisites:
- Connect a battery charger.
- Cycle the Parking Brake ON, then OFF first.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake calipers will then open, allowing the pads to be changed.
[Done, Go Back]
[Close Controller, Go Back - 06]
It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point.
Close Rear Parking Brake
Prerequisites:
- Connect a battery charger.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake calipers will then close.
[Done, Go Back]
[Close Controller, Go Back - 06]
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly. This should stop after cycling the Parking Brake ON, then OFF again.
Function Test
Prerequisites:
- Cycle the Parking Brake ON, then OFF first.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening and closing 3 times.
Important: Wait 30 seconds after the brakes stop moving before carrying out the next step.
Due to a firmware problem in some modules, failure to wait can result in damage to the control module.
[Done, Go Back]
[Close Controller, Go Back - 06]
Longitudinal Acceleration Sensor (G251)
Prerequisites:
- System voltage at least 12.0 V.
- Do NOT move/rock car while performing basic setting.
[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.
[Done, Go Back]