Difference between revisions of "ESP System Function Test"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) |
RtWiKiSyS0p (talk | contribs) |
||
| Line 3: | Line 3: | ||
=== General === | === General === | ||
| − | * The ESP System Function or Road Test serves to check the Plausibility of the Signals from the Lateral Acceleration Sensor (G200), Rotation | + | * The ESP System Function or Road Test serves to check the Plausibility of the Signals from the Lateral Acceleration Sensor (G200), Rotation Rate Sensor (G202) and Brake Pressure Sensor (G201). |
* The ESP System Function Test should be performed after all major work on the Brake System, in some cases the Brake Electronics Control Module (J104) may automatically require this Function Test and set the correlating Fault Code [[01486]]. | * The ESP System Function Test should be performed after all major work on the Brake System, in some cases the Brake Electronics Control Module (J104) may automatically require this Function Test and set the correlating Fault Code [[01486]]. | ||
* '''Once the Function Test has been started it cannot be cancelled and must be successfully finished.''' | * '''Once the Function Test has been started it cannot be cancelled and must be successfully finished.''' | ||
| + | * ''The Diagnostic Tool should NOT need to be connected while performing the Function Test.'' | ||
| Line 18: | Line 19: | ||
=== Instructions === | === Instructions === | ||
| − | * Firmly press the Brake Pedal until a certain Brake Pressure (usually right above 30 bar) is reached | + | * '''Firmly press the Brake Pedal until a certain Brake Pressure (usually right above 30 bar) is reached.''' |
| − | * | + | * Brake Pressure Sensor (G201) Plausibility will be confirmed by a Change in the Brake Electronics Warning Lights. |
** ''On '''Bosch''', the ASR/ESP Warning Light (K155) will switch OFF and the ABS Warning Light (K47) will switch ON.'' | ** ''On '''Bosch''', the ASR/ESP Warning Light (K155) will switch OFF and the ABS Warning Light (K47) will switch ON.'' | ||
** ''On '''Continental/Teves''', the ABS Warning Light (K47) will switch OFF and the ASR/ESP Warning Light (K155) switch ON.'' | ** ''On '''Continental/Teves''', the ABS Warning Light (K47) will switch OFF and the ASR/ESP Warning Light (K155) switch ON.'' | ||
| + | * '''Start Driving straight with a steady Speed of ~20 km/h (~13 mph).''' | ||
| + | * '''Turn the Steering Wheel either Left or Right at a 45 ° Angle (1/4 Turn) and keep it steady.''' | ||
| + | * Lateral Acceleration Sensor (G200) and Rotation Rate Sensor (G202) Plausibility is confirmed once the remaining Brake Electronics Warning Light(s) switch OFF. The Function Test is now completed. | ||
| − | |||
| + | ==== Notes ==== | ||
| − | + | * When Driving, make sure the Speed is between 15 to 30 kph (9 to 18 mph). | |
| + | * The Turn should be done at a Rotation/Turn Rate of ~10 °/s which can be achieved with a Turning Radius of 10 to 12 Meters (30 to 40 feet) with a Speed of 15 to 30 kph (9 to 18 mph). | ||
* If you are experiencing Problems getting the Function Test carried out [http://www.ross-tech.com/contact.html please contact us directly], our Techs have a ''vast Experience'' with this Subject and will gladly assist you with the Process. ''';-)''' | * If you are experiencing Problems getting the Function Test carried out [http://www.ross-tech.com/contact.html please contact us directly], our Techs have a ''vast Experience'' with this Subject and will gladly assist you with the Process. ''';-)''' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Revision as of 17:03, 13 July 2011
ESP System Function Test
General
- The ESP System Function or Road Test serves to check the Plausibility of the Signals from the Lateral Acceleration Sensor (G200), Rotation Rate Sensor (G202) and Brake Pressure Sensor (G201).
- The ESP System Function Test should be performed after all major work on the Brake System, in some cases the Brake Electronics Control Module (J104) may automatically require this Function Test and set the correlating Fault Code 01486.
- Once the Function Test has been started it cannot be cancelled and must be successfully finished.
- The Diagnostic Tool should NOT need to be connected while performing the Function Test.
Prerequisites
- Vehicle stationary
- Ignition ON, Engine ON (Running)
- Perform the Test Drive on an enclosed Site (i.e. a Parking Lot)
- Make sure to Complete the Function Test within 50 Seconds after pressing the Brake Pedal
Instructions
- Firmly press the Brake Pedal until a certain Brake Pressure (usually right above 30 bar) is reached.
- Brake Pressure Sensor (G201) Plausibility will be confirmed by a Change in the Brake Electronics Warning Lights.
- On Bosch, the ASR/ESP Warning Light (K155) will switch OFF and the ABS Warning Light (K47) will switch ON.
- On Continental/Teves, the ABS Warning Light (K47) will switch OFF and the ASR/ESP Warning Light (K155) switch ON.
- Start Driving straight with a steady Speed of ~20 km/h (~13 mph).
- Turn the Steering Wheel either Left or Right at a 45 ° Angle (1/4 Turn) and keep it steady.
- Lateral Acceleration Sensor (G200) and Rotation Rate Sensor (G202) Plausibility is confirmed once the remaining Brake Electronics Warning Light(s) switch OFF. The Function Test is now completed.
Notes
- When Driving, make sure the Speed is between 15 to 30 kph (9 to 18 mph).
- The Turn should be done at a Rotation/Turn Rate of ~10 °/s which can be achieved with a Turning Radius of 10 to 12 Meters (30 to 40 feet) with a Speed of 15 to 30 kph (9 to 18 mph).
- If you are experiencing Problems getting the Function Test carried out please contact us directly, our Techs have a vast Experience with this Subject and will gladly assist you with the Process. ;-)