Audi A3 (8P) Airbag 9.41

From Ross-Tech Wiki
Revision as of 08:24, 24 April 2006 by RtWiKiSyS0p (talk | contribs) (Added coding)


Coding

  • 0?xxxxx: Battery Seperating
    • 0 = not installed
    • 1 = installed (3.2l only)
  • 0x?xxxx: Stages
    • 3 = North America (USA/Canada)
    • 7 = Rest of World (RoW)
  • 0xx?xxx: Options
    • 0 = without Passenger Airbag Shut-Off (PR-4UE+9P0/9P1)
    • 0 = without Passenger Seat Occupation Detection (PR-4UB+9P1)
    • 1 = with Passenger Airbag Deactivation Key Switch with/without Belt Warning Driver Side (PR-4UF+9P0/9P1)
    • 2 = with Passenger Seat Occupation Detection and Airbag Disabled Warning Light (PR-4UB+9P5)
    • 3 = without Passenger Airbag Shut-Off and with Belt Warning Driver & Passenger Side (PR-4UE+9P3)
    • 4 = with Passenger Airbag Deactivation Key Switch and with Belt Warning Driver & Passenger Side (PR-4UF+9P3)
  • 0xxx?xx: Side Airbags
    • 4 = Front Side Airbags (PR-4X1)
    • 5 = Front & Rear Side Airbags (PR-4X2)
    • 6 = Front Side Airbags with Head Airbags (PR-4X3)
    • 7 = Front & Rear Side Airbags with Head Airbags (PR-4X4)
  • 0xxxx?x: Belt Inquiry
    • 0 = North America (USA/Canada)
    • 1 = Rest of World (RoW): with/without Belt Inquiry Driver's Side (PR-9P0/9P1)
    • 2 = Rest of World (RoW): Belt Inquiry Driver's & Passenger Side (PR-9P3)
  • 0xxxxx?: Belt Tensioner
    • 2 = Rest of World (RoW)
    • 5 = North America (USA/Canada)


Adaptation

Used to deactivate individual airbag components (see repair manual for details).

Basic Setting

Seat Occupied Recognition Control Module (J706)

If the Seat Occupied Recognition Control Module (J706) or the seat itself have been replaced, the basic setting has to be performed.

[Select]
[15 - Airbags]
[Security Access - 16]
Enter 30475, to enable the basic setting.
If you are having problems performing this security access, contact us.
[Do it!]
[Basic Settings - 04]
Group 001
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The reset has been performed.
[Done, Go Back]
[Close Controller, Go Back - 06]

Special Procedures

Seat Occupied Recognition Control Module (J706): Reset

If a repair on the Seat Occupied Recognition has been performed, a reset has to be performed too.

Prerequisites:

  • Seat in normal position.
  • Seat must NOT be occupied during the whole procedure.
  • Seatbelt must NOT be plugged in.
  • No faults in the system.
  • Interior temperature must be between 0 °C and 37 °C (32 °F and 98 °F).

[Select]
[15 - Airbags]
[Security Access - 16]
Enter 30475, to enable the basic setting.
If you are having problems performing this security access, contact us.
[Do it!]
[Adaptation - 10]
Channel 000
[Read]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=Audi_A3_(8P)_Airbag_9.41&oldid=1889"