Immobilizer IV ECU Swapping
This procedure details how to change the Engine Control Unit (ECU) on VW/Audi/Seat/Skoda vehicles with Immobilizer IV.
Determining VIN (ECU) & IMMO-ID/Challenge
[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID (does not apply for all models).
[Done, Go Back]
On models which do not have an IMMO-ID you need to use the IMMO-Challenge instead.
[Advanced ID - 1A]
See the field IMMO-Challenge for the current value, keep in mind that the challenge changes with every ignition cycle!
[Close Controller, Go Back - 06]
Determining VIN (Instrument Cluster) & IMMO-ID/Challenge
[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID (does not apply for all models).
[Done, Go Back]
On models which do not have an IMMO-ID you need to use the IMMO-Challenge instead.
[Advanced ID - 1A]
See the field IMMO-Challenge for the current value, keep in mind that the challenge changes with every ignition cycle!
[Close Controller, Go Back - 06]
Engine Control Unit (ECU) Swapping (USED ECU)
Prerequisites:
- The NEW (USED) ECU is already installed in the car.
- Battery voltage at least 12.0 V.
- All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) ECU to the NEW (USED) ECU.
- Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) ECU.
[Select]
[01 - Engine]
[Security Access - 16]
For the following procedure, use the PIN of the NEW (USED) ECU.
- 4/5-digit PIN
- The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
[Do it!]
- The instrument cluster now shows Immobilizer Adaptation active, wait until it changes to Immobilizer active - this may take up to 2 Minutes.
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the OLD (ORIGINAL) ECU.
- 4/5-digit PIN
- The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
[Test]
Check the 1st measuring value.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
- Verify that the NEW (USED) ECU now shows the VIN (and if supported IMMO-ID) of the vehicle now.
- The challenge of instrument cluster and ECU never matches, so don't bother checking them.
Engine Control Unit (ECU) Swapping (NEW ECU)
Prerequisites:
- The NEW ECU is already installed in the car.
- Battery voltage at least 12.0 V.
- All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) ECU to the NEW ECU.
- Make sure to have the PIN of the CAR.
[Select]
[01 - Engine]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the CAR.
- 4/5-digit PIN
- The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
[Test]
Check the 1st measuring value.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
- The instrument cluster may now show Immobilizer Adaptation active, wait until it changes to Immobilizer active - this may take up to 2 Minutes.
- Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
- Verify that the NEW ECU now shows the VIN (and if supported IMMO-ID) of the vehicle now.
- The challenge of instrument cluster and ECU never matches, so don't bother checking them.