Audi A3 (8P) Airbag 9.41

Coding

• 0?xxxxx: Battery Seperating
  • 0 = not installed
  • 1 = installed (3.2l only)
• 0x?xxxx: Stages
  • 3 = North America (USA/Canada)
  • 7 = Rest of World (RoW)
• 0xx?xxx: Options
  • 0 = without Passenger Airbag Shut-Off (PR-4UE+9P0/9P1)
  • 0 = without Passenger Seat Occupation Detection (PR-4UB+9P1)
  • 1 = with Passenger Airbag Deactivation Key Switch with/without Belt Warning Driver Side (PR-4UF+9P0/9P1)
  • 2 = with Passenger Seat Occupation Detection and Airbag Disabled Warning Light (PR-4UB+9P5)
  • 3 = without Passenger Airbag Shut-Off and with Belt Warning Driver & Passenger Side (PR-4UE+9P3)
  • 4 = with Passenger Airbag Deactivation Key Switch and with Belt Warning Driver & Passenger Side (PR-4UF+9P3)
• 0xxx?xx: Side Airbags
  • 1 = 2-Door: Front Side Airbags (PR-4X1)
  • 4 = 4-Door: Front Side Airbags (PR-4X1)
  • 5 = Front & Rear Side Airbags (PR-4X2)
  • 6 = Front Side Airbags with Head Airbags (PR-4X3)
  • 7 = Front & Rear Side Airbags with Head Airbags (PR-4X4)
• 0xxxx?x: Belt Inquiry
  • 0 = North America (USA/Canada)
  • 0 = Rest of World (RoW) & 2-Door: without Belt Inquiry Driver's Side (PR-9P0)
  • 1 = Rest of World (RoW) & 2-Door: with Belt Inquiry Driver's Side (PR-9P1)
  • 1 = Rest of World (RoW) & 4-Door: with/without Belt Inquiry Driver's Side (PR-9P0/9P1)
  • 2 = Rest of World (RoW): Belt Inquiry Driver's & Passenger Side (PR-9P3)
• 0xxxxx?: Belt Tensioner
  • 2 = Rest of World (RoW)
  • 5 = North America (USA/Canada)

Note: After replacing the contro module, make sure the ESP data is set too (see adaptation channel 050).

Adaptation

ESP-Data (Powertrain)

[Select]
[15 - Airbags]
[Adaptation - 10]
Channel 050
[Read]

• 1 = Front-Wheel-Drive (FWD)
• 2 = All-Wheel-Drive (AWD)

[Test]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

Basic Setting

Seat Occupied Recognition Control Module (J706)

If the Seat Occupied Recognition Control Module (J706) or the seat itself have been replaced, the basic setting has to be performed.

[Select]
[15 - Airbags]
[Security Access - 16]
Enter 30475, to enable the basic setting.
If you are having problems performing this security access, contact us.
[Do it!]
[Basic Settings - 04]
Group 001
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The reset has been performed.
[Done, Go Back]
[Close Controller, Go Back - 06]

Special Procedures

Seat Occupied Recognition Control Module (J706): Reset

If a repair on the Seat Occupied Recognition has been performed, a reset has to be performed too.

Prerequisites:

• Seat in normal position.
• Seat must NOT be occupied during the whole procedure.
• Seatbelt must NOT be plugged in.
• No faults in the system.
• Interior temperature must be between 0 °C and 37 °C (32 °F and 98 °F).
  
  

[Select]
[15 - Airbags]
[Security Access - 16]
Enter 30475, to enable the basic setting.
If you are having problems performing this security access, contact us.
[Do it!]
[Adaptation - 10]
Channel 000
[Read]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]