Difference between revisions of "00003"

From Ross-Tech Wiki
 
(3 intermediate revisions by 2 users not shown)
Line 21: Line 21:
 
* When found in [[Audi A8/S8 (4E)]]: [[Audi A8 (4E) Brake Electronics]], this Fault Code may have been stored after performing an Output Test in the Brake Electronics Control Module w/o following the proper Instructions. To clear this Fault Code, please perform/repeat the following Steps 3 (THREE) times:
 
* When found in [[Audi A8/S8 (4E)]]: [[Audi A8 (4E) Brake Electronics]], this Fault Code may have been stored after performing an Output Test in the Brake Electronics Control Module w/o following the proper Instructions. To clear this Fault Code, please perform/repeat the following Steps 3 (THREE) times:
 
** Switch the Ignition OFF for 5 Seconds, then Switch it ON again.
 
** Switch the Ignition OFF for 5 Seconds, then Switch it ON again.
** Clear Fault Codes in Brake Electronics Control Module.
+
** Clear Fault Codes in Brake Electronics Control Module, then exit out of the Control Module.
 
 
  
 
=== 00003 - Control Module: No or Incorrect Basic Setting / Adaptation  ===
 
=== 00003 - Control Module: No or Incorrect Basic Setting / Adaptation  ===
Line 47: Line 46:
 
* When found in any other Audi Instrument Custer run and save an Adaptation Function [[Control Module Maps|Control Module Map]].  After doing so try resetting ALL ''(see note)'' applicable service resets using the [http://www.ross-tech.com/vcds/tour/sri-reset.html [SRI Reset]] function in VCDS. If the issue is not resolved run/save another Adaptation Function Control Module Map so the stored values can be compared. Registered VCDS users encountering difficulty can join and post the inquiry in our [http://forums.ross-tech.com/ forum] -or- contact us directly via [mailto:Support@Ross-Tech.com email] with the log files.
 
* When found in any other Audi Instrument Custer run and save an Adaptation Function [[Control Module Maps|Control Module Map]].  After doing so try resetting ALL ''(see note)'' applicable service resets using the [http://www.ross-tech.com/vcds/tour/sri-reset.html [SRI Reset]] function in VCDS. If the issue is not resolved run/save another Adaptation Function Control Module Map so the stored values can be compared. Registered VCDS users encountering difficulty can join and post the inquiry in our [http://forums.ross-tech.com/ forum] -or- contact us directly via [mailto:Support@Ross-Tech.com email] with the log files.
 
''Note most RoW (Rest of World) market Audi models support 3 total service related reset procedures. The Basic Oil Change, Time based and Distance based resets may need to be completed before 00003 - Control Module: No or Incorrect Basic Setting / Adaptation will clear. ''
 
''Note most RoW (Rest of World) market Audi models support 3 total service related reset procedures. The Basic Oil Change, Time based and Distance based resets may need to be completed before 00003 - Control Module: No or Incorrect Basic Setting / Adaptation will clear. ''
 +
 +
=== 00003 - Control Module: Mechanical Failure ===
 +
* When found in [28] - Heating/Air Conditioning (Rear) in the [[Audi Q7 (4L) | Audi Q7 (4L/FE)]] chassis this may be caused by activated child locks  (i.e. main window switch lock-out active). The rear display may show (- - -). The following TPIs apply:
 +
** RoW market 2014727
 +
** NAR market  2014876
 +
 +
=== Video Link ===
 +
[[File:ABS_025_-_026_thumb.jpg|alt="Video thumbnail for fault 00003 guide"|200px|link=https://www.youtube.com/watch?v=b6lm9OmC2so]]
 +
 +
https://www.youtube.com/watch?v=b6lm9OmC2so
 
[[Category:Fault Codes]]
 
[[Category:Fault Codes]]

Latest revision as of 12:58, 25 September 2021

00003 - Control Module

00003 - Control Module: Defective

Possible Causes

  • Control Module faulty
  • Control Module Software Issue

Possible Solutions

  • Check Control Module
    • Check for Control Module Software Update
  • Replace Control Module

Special Notes

  • When found in Radio OR Radio Navigation System, check Measuring Value Block (MVB) 025.1 for Details.
    • Measuring Value Block 025.1 (MVB) may not be supported by all Radios OR Radio Navigation Systems.
  • When found in Audi A8/S8 (4E): Audi A8 (4E) Brake Electronics, this Fault Code may have been stored after performing an Output Test in the Brake Electronics Control Module w/o following the proper Instructions. To clear this Fault Code, please perform/repeat the following Steps 3 (THREE) times:
    • Switch the Ignition OFF for 5 Seconds, then Switch it ON again.
    • Clear Fault Codes in Brake Electronics Control Module, then exit out of the Control Module.

00003 - Control Module: No or Incorrect Basic Setting / Adaptation

Possible Causes

  • Basic Setting(s) not performed

Possible Solutions

  • Perform Basic Setting(s)

Special Notes

Note most RoW (Rest of World) market Audi models support 3 total service related reset procedures. The Basic Oil Change, Time based and Distance based resets may need to be completed before 00003 - Control Module: No or Incorrect Basic Setting / Adaptation will clear.

00003 - Control Module: Mechanical Failure

  • When found in [28] - Heating/Air Conditioning (Rear) in the Audi Q7 (4L/FE) chassis this may be caused by activated child locks (i.e. main window switch lock-out active). The rear display may show (- - -). The following TPIs apply:
    • RoW market 2014727
    • NAR market 2014876

Video Link

"Video thumbnail for fault 00003 guide"

https://www.youtube.com/watch?v=b6lm9OmC2so