Difference between revisions of "00003"

From Ross-Tech Wiki
Line 40: Line 40:
 
** Details for [[Audi A8 (4E)]]: [[Audi A8 (4E) Control Head Front|Multi Media Interface (MMI)]]
 
** Details for [[Audi A8 (4E)]]: [[Audi A8 (4E) Control Head Front|Multi Media Interface (MMI)]]
 
** Details for [[Audi Q7 (4L)]]: [[Audi Q7 (4L) Control Head Front (High)|Multi Media Interface (MMI)]]
 
** Details for [[Audi Q7 (4L)]]: [[Audi Q7 (4L) Control Head Front (High)|Multi Media Interface (MMI)]]
* When found in [[Audi A3/S3 (8P)]]: [[Audi A3 (8P) Instrument Cluster|Instrument Cluster]]:
 
** Check/Perform Instrument Cluster Service Interval Settings (Adaptation Channels 42, 43, 44, 45 and 49)  <font color=white> E?ID=135368 </font>
 
 
* When found in [[VW Golf (1K) Brake Electronics (MK60EC1)|Brake Electronics (MK60EC1)]]:
 
* When found in [[VW Golf (1K) Brake Electronics (MK60EC1)|Brake Electronics (MK60EC1)]]:
 
** Replacing the Brake Electronics Control Module (J104) but keeping the (old) Hydraulics Unit will result in the Intake and Disconnecting Valves not being synchronized. A [[VW Golf (1K) Brake Electronics (MK60EC1)| Basic Setting for the Intake/Disconnecting Valves]] will solve this problem.
 
** Replacing the Brake Electronics Control Module (J104) but keeping the (old) Hydraulics Unit will result in the Intake and Disconnecting Valves not being synchronized. A [[VW Golf (1K) Brake Electronics (MK60EC1)| Basic Setting for the Intake/Disconnecting Valves]] will solve this problem.
 
* When found in the [[Audi A4 (8E) Automatic Roof | Audi A4 (8H) Automatic Roof]] perform the Adaptation and see the Special Notes.
 
* When found in the [[Audi A4 (8E) Automatic Roof | Audi A4 (8H) Automatic Roof]] perform the Adaptation and see the Special Notes.
 +
* When found in [[Audi A3/S3 (8P)]]: [[Audi A3 (8P) Instrument Cluster|Instrument Cluster]]:
 +
** Check/Perform Instrument Cluster Service Interval Settings (Adaptation Channels 42, 43, 44, 45 and 49)  <font color=white> E?ID=135368 </font>
 +
* When found in any other Audi Instrument Custer run and save an Adaptation Function [[Control Module Maps|Control Module Map]].  After doing so try resetting ALL ''(see note)'' applicable service resets using the [http://www.ross-tech.com/vcds/tour/sri-reset.html [SRI Reset]] function in VCDS. If the issue is not resolved run/save another Adaptation Function Control Module Map so the stored values can be compared. Registered VCDS users encountering difficulty can join and post the inquiry in our [http://forums.ross-tech.com/ forum] -or- contact us directly via [mailto:Support@Ross-Tech.com email] with the log files.
 +
''Note most RoW (Rest of World) market Audi models support 3 total service related reset procedures. The Basic Oil Change, Time based and Distance based resets may need to be completed before 00003 - Control Module: No or Incorrect Basic Setting / Adaptation will clear. ''
 
[[Category:Fault Codes]]
 
[[Category:Fault Codes]]

Revision as of 12:35, 6 March 2015

00003 - Control Module

00003 - Control Module: Defective

Possible Causes

  • Control Module faulty
  • Control Module Software Issue

Possible Solutions

  • Check Control Module
    • Check for Control Module Software Update
  • Replace Control Module

Special Notes

  • When found in Radio OR Radio Navigation System, check Measuring Value Block (MVB) 025.1 for Details.
    • Measuring Value Block 025.1 (MVB) may not be supported by all Radios OR Radio Navigation Systems.
  • When found in Audi A8/S8 (4E): Audi A8 (4E) Brake Electronics, this Fault Code may have been stored after performing an Output Test in the Brake Electronics Control Module w/o following the proper Instructions. To clear this Fault Code, please perform/repeat the following Steps 3 (THREE) times:
    • Switch the Ignition OFF for 5 Seconds, then Switch it ON again.
    • Clear Fault Codes in Brake Electronics Control Module.


00003 - Control Module: No or Incorrect Basic Setting / Adaptation

Possible Causes

  • Basic Setting(s) not performed

Possible Solutions

  • Perform Basic Setting(s)

Special Notes

Note most RoW (Rest of World) market Audi models support 3 total service related reset procedures. The Basic Oil Change, Time based and Distance based resets may need to be completed before 00003 - Control Module: No or Incorrect Basic Setting / Adaptation will clear.