Difference between revisions of "01044"

From Ross-Tech Wiki
m
m
Line 21: Line 21:
 
** On a Long Coded module, use the [http://www.ross-tech.com/vag-com/tour/autoscan.html#gateway Gateway Installation List] to check for unreachable or not registered control modules. Then update the Gateway [http://www.ross-tech.com/vcds/tour/installation-list.html  [Installation List]] by altering the Gateway Coding manually.
 
** On a Long Coded module, use the [http://www.ross-tech.com/vag-com/tour/autoscan.html#gateway Gateway Installation List] to check for unreachable or not registered control modules. Then update the Gateway [http://www.ross-tech.com/vcds/tour/installation-list.html  [Installation List]] by altering the Gateway Coding manually.
 
** On a [http://www.ross-tech.com/vcds/tour/recode_screen.html Short Coded] modules, refresh the original coding with the same value. For example, code it from 00006 -to- 00006 without making an actual change.
 
** On a [http://www.ross-tech.com/vcds/tour/recode_screen.html Short Coded] modules, refresh the original coding with the same value. For example, code it from 00006 -to- 00006 without making an actual change.
 
+
* When found in [[VW New Beetle/Cabriolet (1C/1Y/9C)]]: Comfort System, this may be a Bug in the Control Module Software that will be resolved by refreshing the Coding with the same Value as described above with the CAN Gateway example.
* When found in the Comfort System on the [[VW New Beetle/Cabriolet (1C/1Y/9C)]] this may be a bug in the module that will be resolved by refreshing the coding with the same value as described above with the CAN Gateway example.
 
 
* When found in [[VW Golf (1K) Brake Electronics (MK60EC1)|Brake Electronics (MK60EC1)]] while the Coding is NOT all Zeros, check the '''[19-CAN Gateway]''' > '''[Coding - 07]'''.  An incorrect LHD/RHD Configuration may cause this Fault Code.
 
* When found in [[VW Golf (1K) Brake Electronics (MK60EC1)|Brake Electronics (MK60EC1)]] while the Coding is NOT all Zeros, check the '''[19-CAN Gateway]''' > '''[Coding - 07]'''.  An incorrect LHD/RHD Configuration may cause this Fault Code.
  

Revision as of 10:50, 24 January 2013

01044 - Control Module Incorrectly Coded

Possible Symptoms

  • Reduced Functionality

Possible Causes

  • Control Module incorrectly coded

Possible Solutions

Special Notes

  • When found in CAN-Gateway:
    • On a Long Coded module, use the Gateway Installation List to check for unreachable or not registered control modules. Then update the Gateway [Installation List] by altering the Gateway Coding manually.
    • On a Short Coded modules, refresh the original coding with the same value. For example, code it from 00006 -to- 00006 without making an actual change.
  • When found in VW New Beetle/Cabriolet (1C/1Y/9C): Comfort System, this may be a Bug in the Control Module Software that will be resolved by refreshing the Coding with the same Value as described above with the CAN Gateway example.
  • When found in Brake Electronics (MK60EC1) while the Coding is NOT all Zeros, check the [19-CAN Gateway] > [Coding - 07]. An incorrect LHD/RHD Configuration may cause this Fault Code.

01044 - Control Module Incorrectly Coded: Implausible Signal

Possible Symptoms

  • Reduced Functionality
  • Malfunction Indicator Light (MIL) active

Possible Causes

  • Control Module incorrectly coded

Possible Solutions

Special Notes

  • Some Passat (3B/B5) around MY 2000 have a Firmware Bug which causes this DTC to be set in the CAN Gateway (19). Service Documents for of those Cars indicate that this DTC should be ignored in that Module as long as the Coding matches the Vehicle Equipment.


01044 - Control Module Incorrectly Coded: Mechanical Failure

Possible Causes

  • Coding Pin/Bridge does not match
  • Control Module incorrectly coded

Possible Solutions