Difference between revisions of "18447/P2015/008213"

From Ross-Tech Wiki
 
(One intermediate revision by one other user not shown)
Line 24: Line 24:
 
==== Special Notes ====
 
==== Special Notes ====
  
 +
* Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only.
 +
** 2006 - 2008 BPY and 2008 - 2016 CCTA and CBFA engines.
 +
** Improved intake manifold design.
 +
** https://static.nhtsa.gov/odi/tsbs/2017/MC-10158548-9999.pdf  NHTSA
 
* In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
 
* In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
 
* The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
 
* The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
Line 29: Line 33:
 
** 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
 
** 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
 
* This page describes a Basic Settings for some 2.0T gasoline engines: [[2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner]]
 
* This page describes a Basic Settings for some 2.0T gasoline engines: [[2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner]]
 +
* When found in North America Audi vehicles check Technical Service Bulletin number: 2044003
 +
** This TSB addresses possible issues with the N316 - Intake Manifold Flap Valve
 +
** https://static.nhtsa.gov/odi/tsbs/2016/SB-10093588-0699.pdf  NHTSA
  
 
__FORCETOC__
 
__FORCETOC__
 
[[Category:Fault Codes]]
 
[[Category:Fault Codes]]

Latest revision as of 12:36, 10 January 2022


18447/P2015/008213 - Intake Manifold Flap Position Sensor (Bank 1): Implausible Signal

Possible Symptoms

  • Malfunction Indicator Light (MIL) ON
  • Power Loss

Possible Causes

  • Intake Manifold Flap faulty
  • Intake Manifold Flap Motor (V157) stuck/faulty
  • Engine Control Module Software/Firmware Version faulty
  • Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157) faulty

Possible Solutions

  • Check Intake Manifold Flap
  • Check/Replace Intake Manifold Flap Motor (V157)
    • Perform Output Tests/Basic Setting
  • Check Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157)

Special Notes

  • Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only.
  • In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
  • The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
  • When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version:
    • 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
  • This page describes a Basic Settings for some 2.0T gasoline engines: 2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner
  • When found in North America Audi vehicles check Technical Service Bulletin number: 2044003