View source for 6-Speed Direct Shift Gearbox (DSG/02E)

From Ross-Tech Wiki

← 6-Speed Direct Shift Gearbox (DSG/02E)

You do not have permission to edit this page, for the following reason:

---

You can view and copy the source of this page.

== Basic Setting == '''<u>Prerequisites:</u>'''<br> * Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. * Selector Lever in P * Ignition ON * Engine ON (Idling) for one minute or more * Brake Pedal operated (hold for the whole procedure) * Throttle Pedal not operated<br> '''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.'' '''[Select]'''<br> '''[02 - Transmission]'''<br> '''[Basic Settings - 04]'''<br> === Transmission Tolerances (Engaged Calibration) === Group 061<br> '''[Go!]'''<br> * When you go to Basic Settings 061 and click GO the screen may look like this: [http://img404.imageshack.us/img404/5604/061go.png Basic Settings 061]<br> * Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://img38.imageshack.us/img38/5521/061done.png Basic Settings 061]<br> Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.<br> === Transmission Tolerances (Synch. Point. Measurement) === Group 060<br> '''[Go!]'''<br> * When you go to Basic Settings 060 and click GO the screen may look like this: [http://img227.imageshack.us/img227/5338/060go.png Basic Settings 060]<br> * Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://img695.imageshack.us/img695/5637/060done.png Basic Settings 060]<br> Wait until Basic Settings has switched to ON and all numbers have stopped moving. === Clutch Adaptation === '''''Control Module Software Version < 0800:''''' Group 062<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> '''''Control Module Software Version >= 0800 :''''' Group 067<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (Clutch Safety Function) === Group 068<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (Pressure Adaptation) === Group 065<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (Steering Wheel Paddle Installation) === Group 063<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> === Reset Values (ESP & Tip Cruise Control Installation) === Group 069<br> '''[Go!]'''<br> Activate the Basic Setting.<br> '''[ON/OFF/Next]'''<br> '''[Done, Go Back]'''<br> Switch off Ignition, wait 10 Seconds and switch it back on.<br> '''[Fault Codes - 02]'''<br> Check and clear fault codes after successful test.<br> '''[Close Controller, Go Back - 06]'''<br> Perform the Defined Test Drive.<br><br> == Special Procedures == === Defined Test Drive === ''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br> '''<u>Prerequisites:</u>'''<br> * Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. * Do Not use Cruise Control. Drive in Tiptronic Mode from stand still up to 6th Gear.<br> While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.<br> The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br> Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive, Not Tiptronic Mode.<br> Evaluate creep and starting-off points.<br> Check for leaks.<br> '''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.'' ==== Special Notes ==== * Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own. * It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises. * Customers with TDI's have reported that an RPM range of 1200-1800 rpm is sufficient. [[Category:Transmissions]]

Return to 6-Speed Direct Shift Gearbox (DSG/02E).