Difference between revisions of "6-Speed Direct Shift Gearbox (DSG/02E)"
RtWiKiSyS0p (talk | contribs) |
RtWiKiSyS0p (talk | contribs) |
||
| Line 1: | Line 1: | ||
== Basic Setting == | == Basic Setting == | ||
| + | |||
| + | '''''NOTE:''' Make sure to perform the following steps in a row followed by the defined test drive.'' | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[02 - Transmission]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | |||
| + | === Transmission Tolerances (Enganged Calibration) === | ||
| + | |||
| + | Block 061<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | === Transmission Tolerances (Synch. Point. Measurement) === | ||
| + | |||
| + | Block 060<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | === Clutch Adaptation === | ||
| + | |||
| + | '''''Control Module Software Version < 0800:''''' | ||
| + | |||
| + | Block 062<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | '''''Control Module Software Version >= 0800 :''''' | ||
| + | |||
| + | Block 067<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | === Reset Values (Clutch Safety Function) === | ||
| + | |||
| + | Block 068<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | === Reset Values (Pressure Adaptation) === | ||
| + | |||
| + | Block 065<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | === Reset Values (Steering Wheel Paddle Installation) === | ||
| + | |||
| + | Block 063<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | === Reset Values (ESP & Tip Cruise Control) === | ||
| + | |||
| + | Block 069<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | |||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Fault Codes - 02]'''<br> | ||
| + | Check and clear fault codes after successful test.<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | Perform the Defined Test Drive.<br><br> | ||
| + | |||
| + | |||
== Special Procedures == | == Special Procedures == | ||
| − | === | + | === Defined Test Drive === |
''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br> | ''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br> | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
* ATF Temperature 30...100 °C (86...210 °F) | * ATF Temperature 30...100 °C (86...210 °F) | ||
| + | |||
| + | |||
| + | Drive in Tiptronic Mode from stand still up to 6th Gear.<br> | ||
| + | While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.<br> | ||
| + | The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br> | ||
| + | Perform one sharp braking followed by a full throttle acceleration (oil return check).<br> | ||
| + | Drive with avaluation of crawling and starting-off points.<br> | ||
| + | Check for leaks.<br> | ||
'''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, the remaining quick adaptations are performed automatically in the following driving cycles.'' | '''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, the remaining quick adaptations are performed automatically in the following driving cycles.'' | ||
Revision as of 04:30, 29 November 2006
Basic Setting
NOTE: Make sure to perform the following steps in a row followed by the defined test drive.
[Select]
[02 - Transmission]
[Basic Settings - 04]
Transmission Tolerances (Enganged Calibration)
Block 061
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Transmission Tolerances (Synch. Point. Measurement)
Block 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Clutch Adaptation
Control Module Software Version < 0800:
Block 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Control Module Software Version >= 0800 :
Block 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Clutch Safety Function)
Block 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Pressure Adaptation)
Block 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Steering Wheel Paddle Installation)
Block 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (ESP & Tip Cruise Control)
Block 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
[Done, Go Back]
[Fault Codes - 02]
Check and clear fault codes after successful test.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.
Special Procedures
Defined Test Drive
Suggested test drive after replacing the mechatronic or successful basic setting.
Prerequisites:
- ATF Temperature 30...100 °C (86...210 °F)
Drive in Tiptronic Mode from stand still up to 6th Gear.
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).
Perform one sharp braking followed by a full throttle acceleration (oil return check).
Drive with avaluation of crawling and starting-off points.
Check for leaks.
NOTE: If the test drive cannot be performed in the recommended way or the necessary time, the remaining quick adaptations are performed automatically in the following driving cycles.