Difference between revisions of "65535"

From Ross-Tech Wiki
m
 
(2 intermediate revisions by 2 users not shown)
Line 6: Line 6:
 
==== Possible Causes ====
 
==== Possible Causes ====
  
* Control Module housing leaky > Control Module wet
 
 
* Wiring from/to Control Module faulty
 
* Wiring from/to Control Module faulty
 +
** Voltage Supply and/or Ground Supply faulty
 
* Control Module faulty
 
* Control Module faulty
 +
** Control Module Housing leaky
  
 
==== Possible Solutions ====
 
==== Possible Solutions ====
  
 
* Check/Clean Wiring from/to Control Module
 
* Check/Clean Wiring from/to Control Module
 +
** Check Voltage Supply and Ground Supply including the Main Supply/Connections at the Battery
 
* Replace Control Module
 
* Replace Control Module
  
 
==== Special Notes ====
 
==== Special Notes ====
  
* This fault is NOT to be ignored when found in a major and/or critical system (Airbag, ABS etc.).
+
* This fault is NOT to be ignored when found in a major and/or critical system (Airbag, ABS etc.). '''If you try to clear this fault, VCDS may tell you that there is an unexpected result or that the controller refused the command. This is normal since this specific fault can generally not be cleared.'''
 
* When stored in other unimportant systems (Radio etc.) the general suggestion is to ignore it unless you notice functional limitations. Within the warranty period dealers are usually required to replace such control modules, but there have been a couple of cases with similar codes where these are getting ignored due to flaws in the control module software. If in doubt please refer to technical bulletins and similar documents provided by the vehicle manufacturer.
 
* When stored in other unimportant systems (Radio etc.) the general suggestion is to ignore it unless you notice functional limitations. Within the warranty period dealers are usually required to replace such control modules, but there have been a couple of cases with similar codes where these are getting ignored due to flaws in the control module software. If in doubt please refer to technical bulletins and similar documents provided by the vehicle manufacturer.
* Audi Airbag 6 & 7
+
* When found in Audi Airbag Generation 6 & 7 (see Audi TPI 1308401):
** Problem: A fault of the acceleration sensor may result in the above fault.
+
** A Problem with the Acceleration Sensor may result in the Airbag Control Module storing this Fault Code. Replace the Airbag Control Module and both Acceleration Sensors.
** Solution: Replace Airbag control module and both acceleration sensors.
+
* When found in Audi Airbag Generation 8:
* Audi Airbag 8
+
** Due to low Voltage the Control Module does not complete it's Self Test successfully. Replace Airbag Control Module and install a low Voltage Protection Relay to ensure future mishaps won't cause this again. '''UPDATE''' The Protection Relay may not be available anymore, though the Parts Catalog lists updated Control Modules now.
** Problem: Due to under voltage the control module does not complete it's self test successfully.
+
* When found in certain older TDI Engine Control Modules (ECM) which have a vacuum line going to them:
** Solution: Replace Airbag control module and install a under voltage protection relay for it.
+
** Check/Repair the Vacuum Line before and inside the ECM.
* Certain older TDI ECUs which have a vacuum line going to them
 
** Problem:  Vacuum line broken, either before ECU or inside ECU.
 
** Solution: Inspect and repair vacuum lines to ECU and inside ECU.
 
  
 
[[Category:Fault Codes]]
 
[[Category:Fault Codes]]

Latest revision as of 09:31, 9 May 2012

Internal Control Module Memory Error

Internal Control Module Memory Error

Possible Causes

  • Wiring from/to Control Module faulty
    • Voltage Supply and/or Ground Supply faulty
  • Control Module faulty
    • Control Module Housing leaky

Possible Solutions

  • Check/Clean Wiring from/to Control Module
    • Check Voltage Supply and Ground Supply including the Main Supply/Connections at the Battery
  • Replace Control Module

Special Notes

  • This fault is NOT to be ignored when found in a major and/or critical system (Airbag, ABS etc.). If you try to clear this fault, VCDS may tell you that there is an unexpected result or that the controller refused the command. This is normal since this specific fault can generally not be cleared.
  • When stored in other unimportant systems (Radio etc.) the general suggestion is to ignore it unless you notice functional limitations. Within the warranty period dealers are usually required to replace such control modules, but there have been a couple of cases with similar codes where these are getting ignored due to flaws in the control module software. If in doubt please refer to technical bulletins and similar documents provided by the vehicle manufacturer.
  • When found in Audi Airbag Generation 6 & 7 (see Audi TPI 1308401):
    • A Problem with the Acceleration Sensor may result in the Airbag Control Module storing this Fault Code. Replace the Airbag Control Module and both Acceleration Sensors.
  • When found in Audi Airbag Generation 8:
    • Due to low Voltage the Control Module does not complete it's Self Test successfully. Replace Airbag Control Module and install a low Voltage Protection Relay to ensure future mishaps won't cause this again. UPDATE The Protection Relay may not be available anymore, though the Parts Catalog lists updated Control Modules now.
  • When found in certain older TDI Engine Control Modules (ECM) which have a vacuum line going to them:
    • Check/Repair the Vacuum Line before and inside the ECM.