Difference between revisions of "Audi A4 (8D) Brake Electronics (Bosch 5.3 ABS/EDS/ASR/ESP)"

From Ross-Tech Wiki
 
(17 intermediate revisions by 4 users not shown)
Line 2: Line 2:
 
== Login ==
 
== Login ==
  
'''''Note #1''': After Login has been carried out you need to recode the control module.''<br>
+
'''''Note #1''': After Login has been carried out you need to Recode the control module then perform the Steering Angle Sensor Calibration. Do NOT exit the Control Module in between the individual steps.''<br>
 
'''''Note #2''': For Audi A8 (4D) always use '''4''' as Selection for Brakes.''<br>
 
'''''Note #2''': For Audi A8 (4D) always use '''4''' as Selection for Brakes.''<br>
'''''Note #3''': ''The PR codes ( such as 1LB ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker'' http://www.ross-tech.net/vag-com/misc-images/PR-Codes.png<br>
+
'''''Note #3''': The Production Codes (PR-Code) such as '''1LX''' can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. <br> Click [[Production Codes (PR-Codes) can be found on the Vehicle Data Label | here to see an Example of a Sticker]].''<br>
 +
 
  
 
* '''0?xxx''': ''Chassis''
 
* '''0?xxx''': ''Chassis''
Line 12: Line 13:
 
* '''0x?xx''': ''Brakes''
 
* '''0x?xx''': ''Brakes''
 
** 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
 
** 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
** 4 = FN2/HP2 (Dual-Piston) [PR-1LX]
+
** 4 = FN2/HP2 (Dual-Piston) [PR-1LX] & Brembo [PR-1ZL/1LJ]
** 5 = FN3 (Teves/ATE) [PR-1LB]
+
** 5 = FN3 (Teves/ATE) [PR-1LB/1LE/1LF/1LT/1ZC]
 
** 6 = C54 (Lucas) [PR-1LZ]
 
** 6 = C54 (Lucas) [PR-1LZ]
 
* '''0xx?x''': ''Engine''
 
* '''0xx?x''': ''Engine''
Line 22: Line 23:
 
** 3 = Manual with Low Range (only Audi A6 Allroad)
 
** 3 = Manual with Low Range (only Audi A6 Allroad)
 
** 5 = Manual
 
** 5 = Manual
** 7 = Automatic (01N/01V)
+
** 7 = Automatic (01L/01N/01V)
 
** 9 = Multitronic (01J)
 
** 9 = Multitronic (01J)
 
  
 
== Coding ==
 
== Coding ==
  
 
'''''Note #1''': Coding is accepted after a specific login has been carried out.''<br>
 
'''''Note #1''': Coding is accepted after a specific login has been carried out.''<br>
'''''Note #2''': After successful coding the steering angle sensor basic setting needs to be carried out.''<br>
+
'''''Note #2''': After successful coding the steering angle sensor basic setting needs to be carried out.'' '''Do NOT exit the Control Module in between the individual steps'''<br>
 
'''''Note #3''': For Audi A8 (4D) always use '''3''' as Selection for Brakes.''<br>
 
'''''Note #3''': For Audi A8 (4D) always use '''3''' as Selection for Brakes.''<br>
'''''Note #4''': In some cases, you will need to enter a non-zero WSC, such as 12345.''<br>
+
'''''Note #4''': The Production Codes (PR-Code) such as '''1LX''' can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click [[Production Codes (PR-Codes) can be found on the Vehicle Data Label | here to see an Example of a Sticker]].''<br>
'''''Note #5''': ''The PR codes ( such as 1LB ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker'' http://www.ross-tech.net/vag-com/misc-images/PR-Codes.png<br>
+
'''''Note #5''': In some cases, you will need to enter a non-zero WorkShop Code, such as 12345-123-12345.''<br>
 +
 
  
 
* '''0?xxx''': ''Chassis''
 
* '''0?xxx''': ''Chassis''
Line 40: Line 41:
 
* '''0x?xx''': ''Brakes''
 
* '''0x?xx''': ''Brakes''
 
** 1 = C54 (Lucas) [PR-1LZ]
 
** 1 = C54 (Lucas) [PR-1LZ]
** 2 = FN3 (Teves/ATE) [PR-1LB]
+
** 2 = FN3 (Teves/ATE) [PR-1LB/1LE/1LF/1LT/1ZC]
** 3 = FN2/HP2 (Dual-Piston) [PR-1LX]
+
** 3 = FN2/HP2 (Dual-Piston) [PR-1LX] & Brembo [PR-1ZL/1LJ]
 
** 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
 
** 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
 
* '''0xx?x''': ''Engine''
 
* '''0xx?x''': ''Engine''
Line 50: Line 51:
 
** 3 = Manual with Low Range (only Audi A6 Allroad)
 
** 3 = Manual with Low Range (only Audi A6 Allroad)
 
** 5 = Manual
 
** 5 = Manual
** 7 = Automatic (01N/01V)
+
** 7 = Automatic (01L/01N/01V)
 
** 9 = Multitronic (01J)
 
** 9 = Multitronic (01J)
 
  
 
== Basic Setting ==
 
== Basic Setting ==
Line 58: Line 58:
 
=== Steering Angle Sensor (G85) Calibration ===
 
=== Steering Angle Sensor (G85) Calibration ===
  
'''''Note''': ''Make sure the above Login and Coding have been done successfully before proceeding.''<br>
+
Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.<br>
  
 
'''[Meas. Blocks - 08]'''<br>
 
'''[Meas. Blocks - 08]'''<br>
 
Group 005 Field 1 (Steering Angle Sensor -G85-)<br>
 
Group 005 Field 1 (Steering Angle Sensor -G85-)<br>
Turn steering wheel at least 30 ° left and back straight ahead.<br>
 
 
Specification: 0.0 °<br>
 
Specification: 0.0 °<br>
 
Tolerance (when straight): ±5.0 °<br>
 
Tolerance (when straight): ±5.0 °<br>
Line 80: Line 79:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
  
'''[Close Controller, Go Back - 06]'''<br>
+
==== Note ====
 +
After doing the G85 Calibration, you may get a 01486 - System Function Test Active, this is normal.  Please see [[01486]].
 +
 
 +
 
 +
== Video Link ==
 +
=== Bosch 5.3 and 5.7 ABS with ESP, Coding ===
 +
 
 +
[[File:Titlescreen.jpg|200px|link=http://www.youtube.com/watch?v=G7YRiVYrLjo]]
 +
 
 +
http://www.youtube.com/watch?v=G7YRiVYrLjo

Latest revision as of 09:25, 19 September 2022

Login

Note #1: After Login has been carried out you need to Recode the control module then perform the Steering Angle Sensor Calibration. Do NOT exit the Control Module in between the individual steps.
Note #2: For Audi A8 (4D) always use 4 as Selection for Brakes.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual.
Click here to see an Example of a Sticker.


  • 0?xxx: Chassis
    • 5 = Audi A8 (4D)
    • 7 = Audi A6 (4B)
    • 9 = Audi A4 (8D) / VW Passat (3B)
  • 0x?xx: Brakes
    • 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
    • 4 = FN2/HP2 (Dual-Piston) [PR-1LX] & Brembo [PR-1ZL/1LJ]
    • 5 = FN3 (Teves/ATE) [PR-1LB/1LE/1LF/1LT/1ZC]
    • 6 = C54 (Lucas) [PR-1LZ]
  • 0xx?x: Engine
    • 5 = 4/6/8 Cyl. Diesel
    • 7 = 4/5 Cyl. Gasoline
    • 9 = 6/8/12 Cyl. Gasoline
  • 0xxx?: Transmission
    • 3 = Manual with Low Range (only Audi A6 Allroad)
    • 5 = Manual
    • 7 = Automatic (01L/01N/01V)
    • 9 = Multitronic (01J)

Coding

Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out. Do NOT exit the Control Module in between the individual steps
Note #3: For Audi A8 (4D) always use 3 as Selection for Brakes.
Note #4: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
Note #5: In some cases, you will need to enter a non-zero WorkShop Code, such as 12345-123-12345.


  • 0?xxx: Chassis
    • 4 = Audi A4 (8D) / VW Passat (3B)
    • 6 = Audi A6 (4B)
    • 8 = Audi A8 (4D)
  • 0x?xx: Brakes
    • 1 = C54 (Lucas) [PR-1LZ]
    • 2 = FN3 (Teves/ATE) [PR-1LB/1LE/1LF/1LT/1ZC]
    • 3 = FN2/HP2 (Dual-Piston) [PR-1LX] & Brembo [PR-1ZL/1LJ]
    • 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
  • 0xx?x: Engine
    • 5 = 4/6/8 Cyl. Diesel
    • 7 = 4/5 Cyl. Gasoline
    • 9 = 6/8/12 Cyl. Gasoline
  • 0xxx?: Transmission
    • 3 = Manual with Low Range (only Audi A6 Allroad)
    • 5 = Manual
    • 7 = Automatic (01L/01N/01V)
    • 9 = Multitronic (01J)

Basic Setting

Steering Angle Sensor (G85) Calibration

Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]

Note

After doing the G85 Calibration, you may get a 01486 - System Function Test Active, this is normal. Please see 01486.


Video Link

Bosch 5.3 and 5.7 ABS with ESP, Coding

Titlescreen.jpg

http://www.youtube.com/watch?v=G7YRiVYrLjo