Difference between revisions of "Audi A4 (8D) Brake Electronics (Bosch 5.3 ABS/EDS/ASR/ESP)"

From Ross-Tech Wiki
Line 2: Line 2:
 
== Login ==
 
== Login ==
  
'''''Note #1''': After Login has been carried out you need to recode the control module.''<br>
+
'''''Note #1''': After Login has been carried out you need to recode the Control Module, do not exit the Control Module in between the individual steps.''<br>
 
'''''Note #2''': For Audi A8 (4D) always use '''4''' as Selection for Brakes.''<br>
 
'''''Note #2''': For Audi A8 (4D) always use '''4''' as Selection for Brakes.''<br>
 
'''''Note #3''': ''The PR codes ( such as 1LB ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker'' http://www.ross-tech.net/vag-com/misc-images/PR-Codes.png<br>
 
'''''Note #3''': ''The PR codes ( such as 1LB ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker'' http://www.ross-tech.net/vag-com/misc-images/PR-Codes.png<br>
Line 29: Line 29:
  
 
'''''Note #1''': Coding is accepted after a specific login has been carried out.''<br>
 
'''''Note #1''': Coding is accepted after a specific login has been carried out.''<br>
'''''Note #2''': After successful coding the steering angle sensor basic setting needs to be carried out.''<br>
+
'''''Note #2''': After successful coding the steering angle sensor basic setting needs to be carried out, do not exit the Control Module in between the individual steps.''<br>
 
'''''Note #3''': For Audi A8 (4D) always use '''3''' as Selection for Brakes.''<br>
 
'''''Note #3''': For Audi A8 (4D) always use '''3''' as Selection for Brakes.''<br>
 
'''''Note #4''': In some cases, you will need to enter a non-zero WSC, such as 12345.''<br>
 
'''''Note #4''': In some cases, you will need to enter a non-zero WSC, such as 12345.''<br>

Revision as of 02:09, 2 October 2010

Login

Note #1: After Login has been carried out you need to recode the Control Module, do not exit the Control Module in between the individual steps.
Note #2: For Audi A8 (4D) always use 4 as Selection for Brakes.
Note #3: The PR codes ( such as 1LB ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker PR-Codes.png

  • 0?xxx: Chassis
    • 5 = Audi A8 (4D)
    • 7 = Audi A6 (4B)
    • 9 = Audi A4 (8D) / VW Passat (3B)
  • 0x?xx: Brakes
    • 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
    • 4 = FN2/HP2 (Dual-Piston) [PR-1LX]
    • 5 = FN3 (Teves/ATE) [PR-1LB]
    • 6 = C54 (Lucas) [PR-1LZ]
  • 0xx?x: Engine
    • 5 = 4/6/8 Cyl. Diesel
    • 7 = 4/5 Cyl. Gasoline
    • 9 = 6/8/12 Cyl. Gasoline
  • 0xxx?: Transmission
    • 3 = Manual with Low Range (only Audi A6 Allroad)
    • 5 = Manual
    • 7 = Automatic (01N/01V)
    • 9 = Multitronic (01J)


Coding

Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out, do not exit the Control Module in between the individual steps.
Note #3: For Audi A8 (4D) always use 3 as Selection for Brakes.
Note #4: In some cases, you will need to enter a non-zero WSC, such as 12345.
Note #5: The PR codes ( such as 1LB ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker PR-Codes.png

  • 0?xxx: Chassis
    • 4 = Audi A4 (8D) / VW Passat (3B)
    • 6 = Audi A6 (4B)
    • 8 = Audi A8 (4D)
  • 0x?xx: Brakes
    • 1 = C54 (Lucas) [PR-1LZ]
    • 2 = FN3 (Teves/ATE) [PR-1LB]
    • 3 = FN2/HP2 (Dual-Piston) [PR-1LX]
    • 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
  • 0xx?x: Engine
    • 5 = 4/6/8 Cyl. Diesel
    • 7 = 4/5 Cyl. Gasoline
    • 9 = 6/8/12 Cyl. Gasoline
  • 0xxx?: Transmission
    • 3 = Manual with Low Range (only Audi A6 Allroad)
    • 5 = Manual
    • 7 = Automatic (01N/01V)
    • 9 = Multitronic (01J)


Basic Setting

Steering Angle Sensor (G85) Calibration

Note: Make sure the above Login and Coding have been done successfully before proceeding.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Turn steering wheel at least 30 ° left and back straight ahead.
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]

[Close Controller, Go Back - 06]