Difference between revisions of "Audi A4 (8D) Brake Electronics (Bosch 5.3 ABS/EDS/ASR/ESP)"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) |
RtWiKiSyS0p (talk | contribs) |
||
| Line 2: | Line 2: | ||
== Login == | == Login == | ||
| − | ''' | + | * '''Notes''': |
| − | + | ** After Login has been carried out you need to recode the Control Module. | |
| − | + | ** '''Do NOT exit the Control Module in between the individual steps'''. | |
| + | ** For Audi A8 (4D) always use '''4''' as Selection for Brakes. | ||
| + | ** The PR-Codes ( such as 1LB ) can be found in a [http://www.ross-tech.net/vag-com/misc-images/PR-Codes.png sticker near the spare tire well]. | ||
| + | |||
* '''0?xxx''': ''Chassis'' | * '''0?xxx''': ''Chassis'' | ||
| Line 28: | Line 31: | ||
== Coding == | == Coding == | ||
| − | ''''' | + | * '''Notes''' |
| − | + | ** Coding is accepted after a specific login has been carried out. | |
| − | + | ** After successful coding the Steering Angle Sensor Basic Setting needs to be carried out. | |
| − | + | ** '''Do NOT exit the Control Module in between the individual steps'''. | |
| − | + | ** For Audi A8 (4D) always use '''3''' as Selection for Brakes. | |
| + | ** In some cases, you will need to enter a non-zero WSC, such as 12345-123-12345. | ||
| + | ** The PR-Codes ( such as 1LB ) can be found in a [http://www.ross-tech.net/vag-com/misc-images/PR-Codes.png sticker near the spare tire well]. | ||
| + | |||
* '''0?xxx''': ''Chassis'' | * '''0?xxx''': ''Chassis'' | ||
Revision as of 02:18, 2 October 2010
Login
- Notes:
- After Login has been carried out you need to recode the Control Module.
- Do NOT exit the Control Module in between the individual steps.
- For Audi A8 (4D) always use 4 as Selection for Brakes.
- The PR-Codes ( such as 1LB ) can be found in a sticker near the spare tire well.
- 0?xxx: Chassis
- 5 = Audi A8 (4D)
- 7 = Audi A6 (4B)
- 9 = Audi A4 (8D) / VW Passat (3B)
- 0x?xx: Brakes
- 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
- 4 = FN2/HP2 (Dual-Piston) [PR-1LX]
- 5 = FN3 (Teves/ATE) [PR-1LB]
- 6 = C54 (Lucas) [PR-1LZ]
- 0xx?x: Engine
- 5 = 4/6/8 Cyl. Diesel
- 7 = 4/5 Cyl. Gasoline
- 9 = 6/8/12 Cyl. Gasoline
- 0xxx?: Transmission
- 3 = Manual with Low Range (only Audi A6 Allroad)
- 5 = Manual
- 7 = Automatic (01N/01V)
- 9 = Multitronic (01J)
Coding
- Notes
- Coding is accepted after a specific login has been carried out.
- After successful coding the Steering Angle Sensor Basic Setting needs to be carried out.
- Do NOT exit the Control Module in between the individual steps.
- For Audi A8 (4D) always use 3 as Selection for Brakes.
- In some cases, you will need to enter a non-zero WSC, such as 12345-123-12345.
- The PR-Codes ( such as 1LB ) can be found in a sticker near the spare tire well.
- 0?xxx: Chassis
- 4 = Audi A4 (8D) / VW Passat (3B)
- 6 = Audi A6 (4B)
- 8 = Audi A8 (4D)
- 0x?xx: Brakes
- 1 = C54 (Lucas) [PR-1LZ]
- 2 = FN3 (Teves/ATE) [PR-1LB]
- 3 = FN2/HP2 (Dual-Piston) [PR-1LX]
- 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
- 0xx?x: Engine
- 5 = 4/6/8 Cyl. Diesel
- 7 = 4/5 Cyl. Gasoline
- 9 = 6/8/12 Cyl. Gasoline
- 0xxx?: Transmission
- 3 = Manual with Low Range (only Audi A6 Allroad)
- 5 = Manual
- 7 = Automatic (01N/01V)
- 9 = Multitronic (01J)
Basic Setting
Steering Angle Sensor (G85) Calibration
Note: Make sure the above Login and Coding have been done successfully before proceeding.
[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Turn steering wheel at least 30 ° left and back straight ahead.
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]
[Login - 11]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]
[Close Controller, Go Back - 06]