Audi A4 (8D) Brake Electronics (Bosch 5.3 ABS/EDS/ASR/ESP)

From Ross-Tech Wiki
Revision as of 12:12, 9 March 2011 by Andy (talk | contribs)

Login

  • Notes:
    • After Login has been carried out you need to recode the Control Module.
    • Do NOT exit the Control Module in between the individual steps.
    • For Audi A8 (4D) always use 4 as Selection for Brakes.
    • The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual.
      Click here to see an Example of a Sticker.


  • 0?xxx: Chassis
    • 5 = Audi A8 (4D)
    • 7 = Audi A6 (4B)
    • 9 = Audi A4 (8D) / VW Passat (3B)
  • 0x?xx: Brakes
    • 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
    • 4 = FN2/HP2 (Dual-Piston) [PR-1LX]
    • 5 = FN3 (Teves/ATE) [PR-1LB]
    • 6 = C54 (Lucas) [PR-1LZ]
  • 0xx?x: Engine
    • 5 = 4/6/8 Cyl. Diesel
    • 7 = 4/5 Cyl. Gasoline
    • 9 = 6/8/12 Cyl. Gasoline
  • 0xxx?: Transmission
    • 3 = Manual with Low Range (only Audi A6 Allroad)
    • 5 = Manual
    • 7 = Automatic (01L/01N/01V)
    • 9 = Multitronic (01J)


Coding

  • Notes
    • Coding is accepted after a specific login has been carried out.
    • After successful coding the Steering Angle Sensor Basic Setting needs to be carried out.
    • Do NOT exit the Control Module in between the individual steps.
    • For Audi A8 (4D) always use 3 as Selection for Brakes.
    • In some cases, you will need to enter a non-zero WSC, such as 12345-123-12345.
    • The PR-Codes ( such as 1LB ) can be found in a sticker near the spare tire well.


  • 0?xxx: Chassis
    • 4 = Audi A4 (8D) / VW Passat (3B)
    • 6 = Audi A6 (4B)
    • 8 = Audi A8 (4D)
  • 0x?xx: Brakes
    • 1 = C54 (Lucas) [PR-1LZ]
    • 2 = FN3 (Teves/ATE) [PR-1LB]
    • 3 = FN2/HP2 (Dual-Piston) [PR-1LX]
    • 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
  • 0xx?x: Engine
    • 5 = 4/6/8 Cyl. Diesel
    • 7 = 4/5 Cyl. Gasoline
    • 9 = 6/8/12 Cyl. Gasoline
  • 0xxx?: Transmission
    • 3 = Manual with Low Range (only Audi A6 Allroad)
    • 5 = Manual
    • 7 = Automatic (01L/01N/01V)
    • 9 = Multitronic (01J)


Basic Setting

Steering Angle Sensor (G85) Calibration

Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]