Difference between revisions of "Audi A5 (8T) Parking Brake"

From Ross-Tech Wiki
(New page: == Basic Setting == === Caution! === * Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic...)
 
 
(14 intermediate revisions by 4 users not shown)
Line 3: Line 3:
 
* Do not perform any of these Basic Settings while the brakes are disassembled!  Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.  
 
* Do not perform any of these Basic Settings while the brakes are disassembled!  Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.  
 
* Please follow the procedures EXACTLY.  There's a reason for every step.  If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.
 
* Please follow the procedures EXACTLY.  There's a reason for every step.  If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.
 
+
* It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults!  There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door.
  
 
=== Open Rear Parking Brake ===
 
=== Open Rear Parking Brake ===
 
'''<u>Prerequisites:</u>'''<br>
 
'''<u>Prerequisites:</u>'''<br>
* Connect a battery charger.
+
* Connect a battery charger as per repair manual.
 
* Cycle the Parking Brake ON, then OFF first.
 
* Cycle the Parking Brake ON, then OFF first.
 
'''[Select]'''<br>
 
'''[Select]'''<br>
Line 14: Line 14:
 
Group 007<br>
 
Group 007<br>
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
Activate the Basic Setting.<br>
 
'''[ON/OFF/Next]'''<br>
 
 
The brake calipers will then open, allowing the pads to be changed.<br>
 
The brake calipers will then open, allowing the pads to be changed.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br><br>
+
'''[Close Controller, Go Back - 06]'''
 +
* Turn ignition off.
 +
<br>
 +
 
 
It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point.
 
It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point.
  
 +
''The caliper pistons do not move back into the caliper, this is normal.''
  
 
=== Close Rear Parking Brake ===
 
=== Close Rear Parking Brake ===
 
'''<u>Prerequisites:</u>'''<br>
 
'''<u>Prerequisites:</u>'''<br>
* Connect a battery charger.
+
* Connect a battery charger as per repair manual.
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[53 - Parking Brake]'''<br>
 
'''[53 - Parking Brake]'''<br>
Line 30: Line 32:
 
Group 006<br>
 
Group 006<br>
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
Activate the Basic Setting.<br>
 
'''[ON/OFF/Next]'''<br>
 
 
The brake calipers will then close.<br>
 
The brake calipers will then close.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
 
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly.  This should stop after cycling the Parking Brake ON, then OFF again.
 
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly.  This should stop after cycling the Parking Brake ON, then OFF again.
 
  
 
=== Function Test ===
 
=== Function Test ===
Line 46: Line 45:
 
Group 010<br>
 
Group 010<br>
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
Activate the Basic Setting.<br>
 
'''[ON/OFF/Next]'''<br>
 
 
The brake pads are now opening and closing 3 times.<br>
 
The brake pads are now opening and closing 3 times.<br>
 
Wait 30 seconds after the the brakes stop making noise.<br>
 
Wait 30 seconds after the the brakes stop making noise.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
 +
 +
=== Vehicle Inclination Sensor (G384) ===
 +
 +
Necessary after Replacing the Parking Brake Control Module (J540)
 +
 +
'''<u>Prerequisites:</u>'''<br>
 +
* Parking brake control module properly installed (bolted down).
 +
* System voltage at least 12.0 V.
 +
* Car parked on a level surface.
 +
* Do NOT move/rock car while performing basic setting.
 +
* Perform Function Test (BS 010) prior to Initiation G384 (BS 020)
 +
 +
'''[Select]'''<br>
 +
'''[53 - Parking Brake]'''<br>
 +
'''[Basic Settings - 04]'''<br>
 +
Group 020<br>
 +
'''[Go!]'''<br>
 +
Activate the Basic Setting.<br>
 +
'''[ON/OFF/Next]'''<br>
 +
The status of the Vehicle Inclination Sensor (G384) is now being displayed.<br>
 +
'''[Done, Go Back]'''<br>
 +
 +
== Video Link ==
 +
=== Electro-Mechanical Parking Brake (EPB): Rear Brake Service ===
 +
 +
[[File:Image4.jpg|200px|link=https://www.youtube.com/watch?v=C9AcboaVGzY]]
 +
 +
https://www.youtube.com/watch?v=C9AcboaVGzY

Latest revision as of 20:09, 6 July 2022

Basic Setting

Caution!

  • Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.
  • Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.
  • It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults! There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door.

Open Rear Parking Brake

Prerequisites:

  • Connect a battery charger as per repair manual.
  • Cycle the Parking Brake ON, then OFF first.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
The brake calipers will then open, allowing the pads to be changed.
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Turn ignition off.


It is normal for the LED in the parking brake switch and the warning lamp in the instrument cluster to blink rapidly at this point.

The caliper pistons do not move back into the caliper, this is normal.

Close Rear Parking Brake

Prerequisites:

  • Connect a battery charger as per repair manual.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
The brake calipers will then close.
[Done, Go Back]
[Close Controller, Go Back - 06]

The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly. This should stop after cycling the Parking Brake ON, then OFF again.

Function Test

Prerequisites:

  • Cycle the Parking Brake ON, then OFF first.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
The brake pads are now opening and closing 3 times.
Wait 30 seconds after the the brakes stop making noise.
[Done, Go Back]
[Close Controller, Go Back - 06]

Vehicle Inclination Sensor (G384)

Necessary after Replacing the Parking Brake Control Module (J540)

Prerequisites:

  • Parking brake control module properly installed (bolted down).
  • System voltage at least 12.0 V.
  • Car parked on a level surface.
  • Do NOT move/rock car while performing basic setting.
  • Perform Function Test (BS 010) prior to Initiation G384 (BS 020)

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The status of the Vehicle Inclination Sensor (G384) is now being displayed.
[Done, Go Back]

Video Link

Electro-Mechanical Parking Brake (EPB): Rear Brake Service

Image4.jpg

https://www.youtube.com/watch?v=C9AcboaVGzY