Difference between revisions of "Audi A6 (4F) Brake Electronics"
| (3 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
== Coding == | == Coding == | ||
| + | |||
| + | Most repair manual sources do not cover this Bosch 8.0 ABS system. When the module is replaced with new it is advised to use the original coding value from the old unit. If this is not possible, registered users can [http://www.ross-tech.com/contact.html contact us directly] with a complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan] and VIN number. | ||
| + | |||
| + | Minor modifications for retrofitting purposes include: | ||
* +0016384 = Trailer Hitch not installed or w/o Control Module for Trailer/Towing Sensor (J345) | * +0016384 = Trailer Hitch not installed or w/o Control Module for Trailer/Towing Sensor (J345) | ||
| Line 7: | Line 11: | ||
=== Steering Angle Sensor (G85) Calibration === | === Steering Angle Sensor (G85) Calibration === | ||
| + | |||
| + | *Start Engine | ||
| + | * Turn the steering wheel to end stops (left/right) then straight ahead.<br> | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[03 - ABS Brakes]'''<br> | '''[03 - ABS Brakes]'''<br> | ||
| − | + | '''[Meas. Blocks - 08]'''<br> | |
| + | Group 005 Field 1 (Steering Angle Sensor -G85-)<br> | ||
| + | Specification: 0.0 °<br> | ||
| + | Tolerance (when straight): ±5.0 °<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
'''[Security Access - 16]'''<br> | '''[Security Access - 16]'''<br> | ||
| Line 31: | Line 42: | ||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
| − | ==== Special | + | ==== Special Note ==== |
* After doing the G85 Calibration, you may get a 01486 - System Function Test Active, this is normal. Please see [[01486]]. | * After doing the G85 Calibration, you may get a 01486 - System Function Test Active, this is normal. Please see [[01486]]. | ||
| + | |||
| + | ---- | ||
| + | |||
| + | == Replacement == | ||
| + | |||
| + | * First, Code the module with the original coding value from the old unit. No Login or Security Access is needed. | ||
| + | * Next, perform the G85 Calibration. | ||
| + | * Make sure that no faults are present and that the ABS and ESP lamps are off when you exit out of the controller. | ||
Latest revision as of 09:00, 5 October 2023
Coding
Most repair manual sources do not cover this Bosch 8.0 ABS system. When the module is replaced with new it is advised to use the original coding value from the old unit. If this is not possible, registered users can contact us directly with a complete Auto Scan and VIN number.
Minor modifications for retrofitting purposes include:
- +0016384 = Trailer Hitch not installed or w/o Control Module for Trailer/Towing Sensor (J345)
Basic Setting
Steering Angle Sensor (G85) Calibration
- Start Engine
- Turn the steering wheel to end stops (left/right) then straight ahead.
[Select]
[03 - ABS Brakes]
[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]
[Security Access - 16]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]
[Close Controller, Go Back - 06]
Special Note
- After doing the G85 Calibration, you may get a 01486 - System Function Test Active, this is normal. Please see 01486.
Replacement
- First, Code the module with the original coding value from the old unit. No Login or Security Access is needed.
- Next, perform the G85 Calibration.
- Make sure that no faults are present and that the ABS and ESP lamps are off when you exit out of the controller.