Difference between revisions of "Audi A8 (4E) Parking Brake"

From Ross-Tech Wiki
m
Line 1: Line 1:
 
__FORCETOC__
 
__FORCETOC__
 
== Coding ==
 
== Coding ==
 +
 +
'''''Note''': When replacing this Control Module it is necessary to perform the Basic Settings [[#Function Test|Function Test (MVB 010)]] and [[#Longitudinal Acceleration Sensor (G251)|Longitudinal Acceleration Sensor (MVB 020)]] first. This sets a Readiness Bit for each of the Basic Settings, Coding will not be accepted without having done this first!''<br>
 +
 +
*'''0000?xx''': ''Engine''
 +
** 1 = 3.0l MPI (Gasoline)
 +
** 2 = 3.0l TDI (Diesel)
 +
** 3 = 3.7l
 +
** 4 = 4.0l
 +
** 5 = 4.2l
 +
** 6 = 6.0l
 +
*'''0000x?x''': ''Transmission''
 +
** 1 = Multitronic (VL30)
 +
** 2 = Automatic Transmission (AL420)
 +
** 3 = Automatic Transmission (AL600)
 +
*'''0000xx?''': ''Country''
 +
** 1 = Rest of World (RoW)
 +
** 2 = USA/Canada
 +
** 3 = Japan
 +
 
== Adaptation ==
 
== Adaptation ==
 
=== Pad Thickness ===
 
=== Pad Thickness ===
Line 32: Line 51:
 
'''''Note:''' Check/change adaptation channel 006 ([[#Pad Thickness|Pad Thickness]]) after changing the pads.''<br><br>
 
'''''Note:''' Check/change adaptation channel 006 ([[#Pad Thickness|Pad Thickness]]) after changing the pads.''<br><br>
  
----
 
  
 
=== Open Rear Parking Brake for Repairs ===
 
=== Open Rear Parking Brake for Repairs ===
Line 47: Line 65:
 
'''[Close Controller, Go Back - 06]'''<br><br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
  
----
 
 
=== Close Rear Parking Brake ===
 
=== Close Rear Parking Brake ===
  
Line 60: Line 77:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
 
'''[Close Controller, Go Back - 06]'''<br><br>
 +
 +
 +
=== Function Test ===
 +
'''<u>Prerequisites:</u>'''<br>
 +
* Cycle the Parking Brake ON, then OFF first.
 +
'''[Select]'''<br>
 +
'''[53 - Parking Brake]'''<br>
 +
'''[Basic Settings - 04]'''<br>
 +
Group 010<br>
 +
'''[Go!]'''<br>
 +
Activate the Basic Setting.<br>
 +
'''[ON/OFF/Next]'''<br>
 +
The brake pads are now opening and closing 3 times.<br>
 +
Wait 30 seconds after the the brakes stop making noise.<br>
 +
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br><br>
 +
 +
 +
=== Longitudinal Acceleration Sensor (G251) ===
 +
 +
'''<u>Prerequisites:</u>'''<br>
 +
* System voltage at least 12.0 V.
 +
* Car parked on a level surface.
 +
* Do NOT move/rock car while performing basic setting.
 +
 +
'''[Select]'''<br>
 +
'''[53 - Parking Brake]'''<br>
 +
'''[Basic Settings - 04]'''<br>
 +
Group 020<br>
 +
'''[Go!]'''<br>
 +
Activate the Basic Setting.<br>
 +
'''[ON/OFF/Next]'''<br>
 +
The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.<br>
 +
'''[Done, Go Back]'''<br>
 +
 +
 +
== Special Procedures ==
 +
 +
* [[Audi A8 (4E) Parking Brake Pad Replacement|Parking Brake Pad Replacement]]

Revision as of 09:26, 27 July 2007

Coding

Note: When replacing this Control Module it is necessary to perform the Basic Settings Function Test (MVB 010) and Longitudinal Acceleration Sensor (MVB 020) first. This sets a Readiness Bit for each of the Basic Settings, Coding will not be accepted without having done this first!

  • 0000?xx: Engine
    • 1 = 3.0l MPI (Gasoline)
    • 2 = 3.0l TDI (Diesel)
    • 3 = 3.7l
    • 4 = 4.0l
    • 5 = 4.2l
    • 6 = 6.0l
  • 0000x?x: Transmission
    • 1 = Multitronic (VL30)
    • 2 = Automatic Transmission (AL420)
    • 3 = Automatic Transmission (AL600)
  • 0000xx?: Country
    • 1 = Rest of World (RoW)
    • 2 = USA/Canada
    • 3 = Japan

Adaptation

Pad Thickness

[Select]
[53 - Parking Brake]
[Adaptation - 10]
Channel 006
[Read]
Enter the current thickness of the new pads (Range: 3 - 14 mm).
[Test]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]


Basic Setting

Open Rear Parking Brake for Pad Change

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 005
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening.
[Done, Go Back]
[Close Controller, Go Back - 06]

Note: Check/change adaptation channel 006 (Pad Thickness) after changing the pads.


Open Rear Parking Brake for Repairs

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening.
[Done, Go Back]
[Close Controller, Go Back - 06]

Close Rear Parking Brake

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now closing.
[Done, Go Back]
[Close Controller, Go Back - 06]


Function Test

Prerequisites:

  • Cycle the Parking Brake ON, then OFF first.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening and closing 3 times.
Wait 30 seconds after the the brakes stop making noise.
[Done, Go Back]
[Close Controller, Go Back - 06]


Longitudinal Acceleration Sensor (G251)

Prerequisites:

  • System voltage at least 12.0 V.
  • Car parked on a level surface.
  • Do NOT move/rock car while performing basic setting.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.
[Done, Go Back]


Special Procedures