Difference between revisions of "Audi CAN Gateway Battery Coding (8T/8K/8R+)"

From Ross-Tech Wiki
(Replaced content with "__FORCETOC__ The information that was on this page moved to the Battery Replacement page.")
 
(2 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
__FORCETOC__
 
__FORCETOC__
 
+
The information that was on this page moved to the [[Battery Replacement]] page.
'''General Information:'''  Most 2009+ Audi A4 and newer models do NOT use a separate 61-Battery Manager.  In these cases battery management is a slave (subsystem) under the 19-CAN-Gateway control module. This page covers those 8T/8K/8R and newer models using a CAN Protocol 19-CAN-Gateway control module.<br>
 
<br>
 
If the vehicle in question uses a diagnostic capable 61-Battery Regulation controller this page ''should'' apply instead:
 
* [[Audi A8 (4E) Battery Replacement|61-Battery Regulation]]<br>
 
<br>
 
----
 
 
 
=== Long Adaptation ===
 
 
 
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long [Long Adaptation-0A]] function under 19-CAN-Gateway control module. Follow the onscreen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.
 
 
 
'''<u>Prerequisites:</u>'''<br>
 
* New Audi Battery Installed
 
** Aftermarket batteries may NOT have a valid Audi Part Number, Vendor code or Serial number.  Ross-Tech cannot offer assistance if the necessary information is missing.
 
* Key On, Engine OFF
 
<br>
 
'''[Select]'''<br>
 
'''[19 - CAN-Gateway]'''<br>
 
'''[Long Adaptation-0A]'''<br>
 
Channel 004<br>
 
'''[Read]'''<br>
 
VCDS  will populate instructions in the form of a pop-up balloon with the formatting.  For example:
 
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ
 
 
N = Battery Part Number (11 Digits)
 
X = Battery Vendor (3 Digits)
 
Z = Battery Serial Number (10 Digits)
 
 
 
'''[Add to Log]'''  ''Saving the original value to a log is strongly recommended''.<br>
 
Type the New Battery details into the '''New value''' field.<br>
 
* Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.
 
'''[Test]''' <br>
 
'''[Save]'''<br>
 
Providing the value was accepted by the controller the new battery coding is complete.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''
 
 
 
<br>
 
'''Note''': The 10 digit serial number may be preceded by the Battery Vendor Code, for instance VA0. See examples below:
 
 
 
{| class="wikitable"  border="0" width="450"
 
|-
 
!colspan="14" style="background:white"| Click on thumbnail image to enlarge.
 
|-
 
| [[File:Battery serial number.jpg|200px|center|caption]]
 
|-
 
| If the code is VA0310314E04G then drop the VA0 and just enter 310314E04G as the Serial Number.
 
|}
 
 
 
 
 
<br>
 
 
 
 
 
=== Special Notes ===
 
* Measuring Block groups 008, 019 and 020 should show Battery information.
 
 
 
* Registered users encountering difficulty can contact us via [mailto:Support@Ross-Tech.com email] -or- join and post in [http://forums.ross-tech.com our forum]. Please include the Auto-Scan, Saved Adaptation Channel 004 Log  prior to modifications, the part number, serial number and vendor code located on the original battery and the details located on the brand new battery in addition to the error message details.
 
 
 
 
 
 
 
[[Category:Subsystems]]
 

Latest revision as of 14:56, 10 May 2016

The information that was on this page moved to the Battery Replacement page.