Difference between revisions of "Audi TT (8N) Brake Electronics (MK60)"
RtWiKiSyS0p (talk | contribs) (New page: __FORCETOC__ == Coding == === ABS/EDS/ASR/ESP (Front-Wheel-Drive) === === ABS/EDS/ASR/ESP (All-Wheel-Drive) === == Basic Setting == === Sensor for Steering Angle (G85) === '''<u>Prereq...) |
|||
| Line 99: | Line 99: | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
| − | * System voltage at least 12.0 V.<br><br> | + | * System voltage at least 12.0 V.<br> |
| + | * Measuring Value Block Group 006, Field 1 is between (-1.5) and (+1.5) m/s²<br><br> | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| Line 113: | Line 114: | ||
After a successful basic setting, field 2 should say "OK".<br> | After a successful basic setting, field 2 should say "OK".<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | To make sure the basic setting was | + | To make sure the basic setting was successful, check the sensor again.<br> |
'''[Measuring Blocks - 08]'''<br> | '''[Measuring Blocks - 08]'''<br> | ||
Group 006<br> | Group 006<br> | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
| − | Check field 1, the value has to be between -1.5 and +1.5 m/s².<br> | + | Re-Check field 1, the value has to be between -1.5 and +1.5 m/s².<br> |
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
| − | |||
== Special Procedures == | == Special Procedures == | ||
Latest revision as of 09:48, 18 May 2015
Coding
ABS/EDS/ASR/ESP (Front-Wheel-Drive)
ABS/EDS/ASR/ESP (All-Wheel-Drive)
Basic Setting
Sensor for Steering Angle (G85)
Prerequisites:
- Start the vehicle.
- Turn the steering wheel one turn to the right and one turn to the left.
- Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
- If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
- Ensure that the steering wheel is not moved again.
- Keep the engine running and do not switch off the ignition.
- System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -4.5 and +4.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]
Lateral Acceleration Sensor (G200)
Prerequisites:
- System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]
Brake Pressure Sensor 1 (G201)
Prerequisites:
- System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 066
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -7.0 and +7.0 bar.
[Done, Go Back]
[Close Controller, Go Back - 06]
Longitudinal Acceleration Sensor (G251)
Prerequisites:
- System voltage at least 12.0 V.
- Measuring Value Block Group 006, Field 1 is between (-1.5) and (+1.5) m/s²
[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 006
[Go!]
Re-Check field 1, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]