Difference between revisions of "Bentley Continental (3W) Tire Pressure Monitoring"
| (3 intermediate revisions by 2 users not shown) | |||
| Line 10: | Line 10: | ||
Group 019<br> | Group 019<br> | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
| − | Check Field 1, it should show the Initialization Status.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br> | + | Check Field 1, it should show the Initialization Status. If the value is 25, no further diagnostic operations should be necessary before the test drive.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br> |
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Security Access - 16]'''<br> | '''[Security Access - 16]'''<br> | ||
| Line 18: | Line 18: | ||
Adaptation Channel '''001'''<br> | Adaptation Channel '''001'''<br> | ||
'''[Read]'''<br> | '''[Read]'''<br> | ||
| − | Enter ''' | + | Enter '''1''' as new Value.<br> |
'''[Test]'''<br> | '''[Test]'''<br> | ||
'''[Save]'''<br> | '''[Save]'''<br> | ||
| Line 36: | Line 36: | ||
* Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster). | * Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster). | ||
* If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis. | * If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis. | ||
| + | |||
| + | ==== Special Notes ==== | ||
| + | |||
| + | * This forum thread goes into some detail on how this type of TPMS operates including meaning of Measuring Blocks: | ||
| + | |||
| + | http://forums.ross-tech.com/showthread.php?4347 | ||
Latest revision as of 13:05, 28 September 2017
Coding
Special Procedures
Initialization
[Select]
[65 - Tire Pressure Monitoring]
[Measuring Blocks - 08]
Group 019
[Go!]
Check Field 1, it should show the Initialization Status. If the value is 25, no further diagnostic operations should be necessary before the test drive.
If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.
[Done, Go Back]
[Security Access - 16]
Enter 10896, to enable the Initilization.
[Do it!]
[Adaptation - 10]
Adaptation Channel 001
[Read]
Enter 1 as new Value.
[Test]
[Save]
- Check the Tire Pressure for all 4/5 wheels and if necessary correct it.
Adaptation Channel 004
[Read]
Enter 1 as new Value.
[Save]
[Done, Go Back]
[Measuring Blocks - 08]
Group 019
[Go!]
Check Field 1, it should show the Initialization Status.
[Done, Go Back]
[Close Controller, Go Back - 06]
- Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster).
- If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis.
Special Notes
- This forum thread goes into some detail on how this type of TPMS operates including meaning of Measuring Blocks: