Checking Cruise Control using Measuring Values

From Ross-Tech Wiki
Revision as of 17:21, 7 April 2011 by Dana (talk | contribs)


Cruise Control Activation

DBW (Drive-by-Wire)

The CCS (Cruise Control System) activation in the DBW (Drive-by-Wire) throttle systems will vary depending on the Engine Control Module.

1) Control modules using Short Coding often use a Login code and the letter "G" is shown in the component field when activated.

Address 01: Engine        Labels: 06A-906-032-AWP.lbl
  Part No: 06A 906 032 LP
  Component: 1.8L R4/5VT     G   0005
  Coding: 07500

Activating Cruise Control on a new (DBW) ECU using Login

DBW (Drive-by-Wire) Factory fresh ECU's often come with cruise control de-activated.

[Select]
[01 - Engine]
[Login - 11] or if that function is not available then use [Coding - 11] instead
Enter 11463 to activate cruise control
[Do It!]


Notes:

  • You may have to cycle the key off and back on before the CCS is activated and the letter "G" is shown in the component field.
  • The Throttle Body Alignment (TBA) may need to be completed before CCS operates.
  • If CCS needs to be de-activated use the Login of: 16167


2) Control modules using Long Coding are activated in the Coding. Due to different Control Modules Vehicle Equipment, the actual Coding Table is not shown here but will automatically be used by the Long Coding Helper with VCDS.

Address 01: Engine (CBF)       Labels: 06J-907-115-CBF.clb
  Part No SW: 1K0 907 115 AL    HW: 1K0 907 115 AK
  Component: 2.0l R4/4V TFSI     0030
  Revision: E3H21---    Serial number:
  Coding: 040301081C070160

Activating Cruise Control on a new (DBW) ECU using Long Coding

[Select]
[01 - Engine]
[Coding - 07]
[Long Coding Helper]
Check the box for CCS and Exit
[Do It!]


Note:

  • You may have to cycle the key off and back on before the CCS is activated and the new coding takes effect.
  • The Throttle Body Alignment (TBA) may need to be completed before CCS operates.
  • Long Coded modules do Not have the letter G in the component field. If you wanted to see if CCS is enabled, use the Long Coding Helper and see if the box is checked.




DBC (Drive-By-Cable)

The CCS (Cruise Control System) on DBC (Drive By Cable) throttle systems may or may Not be controlled by the Engine Control Module. Refer to the factory repair manual for additional details on these older systems.




Checking Cruise Control using Measuring Blocks

Checking CCS using Measuring Blocks normally involves evaluating binary values of related switches.

Gasoline Engines

Gasoline Engines often use Measuring Block 066 to display CCS info. Please refer to the charts below using line A.


Diesel Engines

Diesel Engines often use Measuring Block 006 to display CCS info. Please refer to the charts below using line B:


A) Gasoline Engines Measuring Block Group 066, Field 2 Data
B) Diesel Engines Measuring Block Group 006, Field 2 Data

0 0 0 0 1 0 0 0 0 = Brake Not Depressed 1 = Brake depressed (brake light switch)
0 = Brake Not Depressed 1 = Brake depressed (brake pedal switch)
0 = Clutch Not Depressed 1 = Clutch Depressed (always 1 in Auto. Trans.)
0 = CCS Not active in ECM 1 = CCS active in ECM
N/A N/A
0 = CCS Switched Off TDI only * 1 = CCS Switched On TDI only *
0 = Accel. pedal overide 1 = CCS Operating
0 = Normal CCS 1 = Accel. pedal overide


A) Gasoline Engines Measuring Block Group 066, Field 4 Data
B) Diesel Engines Measuring Block Group 006, Field 4 Data

0 0 0 0 0 0 1 1 0 = CCS Switched Off 1 = CCS Switched On
0 = Cancel/Off Activated 1 = CCS Switched On
0 = SET/ Decel. Not Pressed 1 = SET/ Decel. Button Pressed
0 = Resume/Accel Not Pressed 1 = Resume/Accel Button Pressed
N/A N/A
N/A N/A
N/A N/A
N/A N/A



Note: On vehicles with additional equipment, the [16] - Steering Wheel Electronics module may display additional signals.