Difference between revisions of "Immobilizer III ECU Swapping"

From Ross-Tech Wiki
m
Line 2: Line 2:
 
'''This procedure details how to change the Engine Control Unit (ECU) on VW/Audi/Seat/Skoda vehicles with Immobilizer III.'''
 
'''This procedure details how to change the Engine Control Unit (ECU) on VW/Audi/Seat/Skoda vehicles with Immobilizer III.'''
  
−
== Determining VIN (ECU) & IMMO-ID ==
+
== Determining VIN & IMMO-ID (ECU) ==
  
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[01 - Engine]'''<br>
 
'''[01 - Engine]'''<br>
−
Look at the first "Extra" field. <br>
+
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>
−
If you see something like: "Immo-ID VWZ7Z0W0648696"  You've got Immo-2 (or maybe even Immo-1 in earlier non-US models).<br>
+
'''[Close Controller, Go Back - 06]'''<br>
−
If you see something like "WVZKB58001H231169 VWZ7Z0W0648696" You've got Immo-3.<br>
+
 
−
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>
+
---OR---
−
If the VIN and Immo-ID are not in the Extra field, then check here: <br>
+
 
 +
'''[Select]'''<br>
 +
'''[01 - Engine]'''<br>
 +
'''[Meas. Blocks - 08]'''<br>
 +
Select Block 081.<br>
 +
'''[Go!]'''<br>
 +
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
 +
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 
 +
 
 +
== Determining VIN & IMMO-ID (Instrument Cluster) ==
 +
 
 +
'''[Select]'''<br>
 +
'''[17 - Instruments]'''<br>
 +
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 
 +
---OR---
 +
 
 +
'''[Select]'''<br>
 +
'''[17 - Instruments]'''<br>
 
'''[Meas. Blocks - 08]'''<br>
 
'''[Meas. Blocks - 08]'''<br>
 
Select Block 081.<br>
 
Select Block 081.<br>
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
−
''The first 17-digit string is the VIN. The second 14-digit string is the Immo-ID.''<br>
+
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 +
 +
== Determining VIN & IMMO-ID (Immo Box) ==
  
 +
'''[Select]'''<br>
 +
'''[25 - Immobilizer]'''<br>
 +
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
  
−
== Determining VIN (Instrument Cluster) & IMMO-ID  ==
+
---OR---
  
 
'''[Select]'''<br>
 
'''[Select]'''<br>
Line 25: Line 54:
 
Select Block 081.<br>
 
Select Block 081.<br>
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
−
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID (does not apply for all models).''<br>
+
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 +
 +
== Determining VIN & IMMO-ID (Kessy) ==
 +
 +
'''[Select]'''<br>
 +
'''[05 - Start/Access Authorization]'''<br>
 +
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 +
---OR---
 +
 +
'''[Select]'''<br>
 +
'''[05 - Start/Access Authorization]'''<br>
 +
'''[Meas. Blocks - 08]'''<br>
 +
Select Block 081.<br>
 +
'''[Go!]'''<br>
 +
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
 +
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
  
 
== Engine Control Unit (ECU) Swapping (Used ECU) ==
 
== Engine Control Unit (ECU) Swapping (Used ECU) ==
Line 42: Line 92:
  
  
−
'''[Security Access - 16]'''<br>
+
'''[Login - 11]'''<br>
 
''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>
 
''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>
 
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
 
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
−
* '''4/5-digit PIN'''
+
* '''4-digit PIN'''
 
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.''
 
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.''
 
* '''7-digit PIN'''
 
* '''7-digit PIN'''
Line 55: Line 105:
  
  
−
* ''The instrument cluster now shows '''Immobilizer Adaptation active''', wait until it changes to '''Immobilizer active''' - this may take up to 2 Minutes.''
+
'''[Adaptation - 10]'''<br>
 +
Enter 050 in "Channel Number".<br>
 +
'''[Read]'''<br>
 +
''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>
 +
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
 +
* '''4-digit PIN'''
 +
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.''
 +
* '''7-digit PIN'''
 +
** '''[Use 7-digit PIN/SKC]'''
 +
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
 +
** '''[OK]'''
 +
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
 +
'''[Save]'''<br>
 +
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 
 +
 
 +
* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
 +
* Verify that the NEW (USED) ECU now shows the VIN and if supported IMMO-ID of the vehicle now.
  
  
 +
== Engine Control Unit (ECU) Swapping (NEW ECU) ==
 +
 +
'''<u>Prerequisites:</u>'''<br>
 +
* The '''NEW''' ECU is already installed in the car.
 +
* Battery voltage at least 12.0 V.
 +
* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) ECU to the NEW ECU.
 +
* Make sure to have the PIN of the CAR.
 +
 +
 +
'''[Select]'''<br>
 +
'''[01 - Engine]'''<br>
 
'''[Adaptation - 10]'''<br>
 
'''[Adaptation - 10]'''<br>
 
Enter 050 in "Channel Number".<br>
 
Enter 050 in "Channel Number".<br>
 
'''[Read]'''<br>
 
'''[Read]'''<br>
−
''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>
+
''For the following procedure, '''use the PIN of the CAR'''.''<br>
 
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
 
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
−
* '''4/5-digit PIN'''
+
* '''4-digit PIN'''
 
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.''
 
** The PIN needs to be entered as 5-digit number. ''For example, if your PIN is 1234, enter 01234.''
 
* '''7-digit PIN'''
 
* '''7-digit PIN'''
Line 70: Line 149:
 
** '''[OK]'''
 
** '''[OK]'''
 
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
 
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
 +
'''[Test]'''<br>
 +
Check the 1st measuring value.<br>
 
'''[Save]'''<br>
 
'''[Save]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
Line 76: Line 157:
  
 
* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
 
* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
−
* Verify that the NEW (USED) ECU now shows the VIN (and if supported IMMO-ID) of the vehicle now.
+
* Verify that the NEW ECU now shows the VIN and if supported IMMO-ID of the vehicle now.
−
* The challenge of instrument cluster and ECU never matches, so don't bother checking them.
 

Revision as of 09:48, 14 December 2006

This procedure details how to change the Engine Control Unit (ECU) on VW/Audi/Seat/Skoda vehicles with Immobilizer III.

Determining VIN & IMMO-ID (ECU)

[Select]
[01 - Engine]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Determining VIN & IMMO-ID (Instrument Cluster)

[Select]
[17 - Instruments]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[17 - Instruments]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Determining VIN & IMMO-ID (Immo Box)

[Select]
[25 - Immobilizer]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Determining VIN & IMMO-ID (Kessy)

[Select]
[05 - Start/Access Authorization]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[05 - Start/Access Authorization]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Engine Control Unit (ECU) Swapping (Used ECU)

Prerequisites:

  • The NEW (USED) cluster is installed in the car.
  • Battery voltage at least 12.5 V.
  • All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) ECU to the NEW (USED) ECU.
  • Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) ECU.
  • Make sure to have the Radio Code (for factory radios only).


[Select]
[01 - Engine]


[Login - 11]
For the following procedure, use the PIN of the NEW (USED) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Do it!]


[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the OLD (ORIGINAL) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]


  • Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
  • Verify that the NEW (USED) ECU now shows the VIN and if supported IMMO-ID of the vehicle now.


Engine Control Unit (ECU) Swapping (NEW ECU)

Prerequisites:

  • The NEW ECU is already installed in the car.
  • Battery voltage at least 12.0 V.
  • All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) ECU to the NEW ECU.
  • Make sure to have the PIN of the CAR.


[Select]
[01 - Engine]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the CAR.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Test]
Check the 1st measuring value.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]


  • Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
  • Verify that the NEW ECU now shows the VIN and if supported IMMO-ID of the vehicle now.
Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=Immobilizer_III_ECU_Swapping&oldid=3088"