Difference between revisions of "Immobilizer III ECU Swapping"

From Ross-Tech Wiki
Line 156: Line 156:
 
Enter 11463 to activate cruise control<br>
 
Enter 11463 to activate cruise control<br>
 
'''[Do It!]'''<br>
 
'''[Do It!]'''<br>
 +
 +
 +
== Video Link ==
 +
 +
Immobilizer Gen 3 ECM or Instrument Cluster swapping
 +
 +
[[File:Wiki thumb nail.jpg|200px|link=http://www.youtube.com/watch?v=J5_51qeEyec]]
 +
 +
http://www.youtube.com/watch?v=J5_51qeEyec

Revision as of 16:40, 27 August 2012

This procedure details how to change the Engine Control Unit (ECU) on VW/Audi/Seat/Skoda vehicles with Immobilizer III.

Determining VIN & IMMO-ID

Engine Control Unit (ECU)

[Select]
[01 - Engine]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Immobilizer (integrated in Instrument Cluster)

[Select]
[17 - Instruments]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[17 - Instruments]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Immobilizer (integrated in separate Immo Box)

[Select]
[25 - Immobilizer]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Immobilizer (integrated in Kessy)

[Select]
[05 - Start/Access Authorization]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[05 - Start/Access Authorization]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Engine Control Unit (ECU) Swapping (USED ECU)

Prerequisites:

  • The REPLACEMENT (USED) ECU is installed in the car.
  • Battery voltage at least 12.5 V.
  • All relevant coding and adaptation values have been transferred from the ORIGINAL (OLD) ECU to the REPLACEMENT (USED) ECU.
  • Make sure to have BOTH PIN's, from the ORIGINAL (OLD) and the REPLACEMENT (USED) ECU.
  • Make sure to have the Radio Code (for factory radios only).


[Select]
[01 - Engine]

[Login - 11]
For the following procedure, use the PIN of the REPLACEMENT (USED) ECU.

  • 4-digit PIN
    • The PIN needs to be entered as 5-digit number in the New Value box. For example, if your PIN is 1234, enter 01234.

[Do it!]


[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the ORIGINAL (OLD) ECU.

  • 4-digit PIN
    • The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.

[Test]

  • The values may change to "32000", this is normal

[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]


  • Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
  • Verify that the REPLACEMENT (USED) ECU now shows the VIN and if supported IMMO-ID of the vehicle now.
  • Verify that the REPLACEMENT (USED) ECU has the same Coding as the original unit, or code it from scratch using the repair manual or coding chart in VCDS when applicable.


Engine Control Unit (ECU) Swapping (NEW ECU)

Prerequisites:

  • The NEW ECU is already installed in the car.
  • Battery voltage at least 12.0 V.
  • All relevant coding and adaptation values have been transferred from the ORIGINAL (OLD) ECU to the REPLACEMENT (NEW) ECU.
  • Make sure to have the PIN of the CAR.


[Select]
[01 - Engine]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the CAR.

  • 4-digit PIN
    • The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.

[Test]

  • The values may change to "32000", this is normal

[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
  • Verify that the REPLACEMENT (NEW) ECU now shows the VIN and if supported IMMO-ID of the vehicle now.
  • Verify that the REPLACEMENT (NEW) ECU has the same Coding as the original unit, or code it from scratch using the repair manual or coding chart in VCDS when applicable.
  • Activate Cruise Control if needed on new DBW ECU's



Activating Cruise Control on a new ECU (DBW)

DBW (Drive-by-Wire) Factory fresh ECU's often come with cruise control de-activated.

[Select]
[01 - Engine]
[Login - 11]
Enter 11463 to activate cruise control
[Do It!]


Video Link

Immobilizer Gen 3 ECM or Instrument Cluster swapping

Wiki thumb nail.jpg

http://www.youtube.com/watch?v=J5_51qeEyec