Difference between revisions of "Immobilizer III Immobilizer Swapping (Kessy)"

From Ross-Tech Wiki
 
m
Line 45: Line 45:
 
'''<u>Prerequisites:</u>'''<br>
 
'''<u>Prerequisites:</u>'''<br>
 
* The NEW module is installed in the car.
 
* The NEW module is installed in the car.
 +
* ORIGINAL Electric Steering Lock is still installed.
 
* Battery voltage at least 12.0 V.
 
* Battery voltage at least 12.0 V.
 
* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.
 
* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.
 +
 +
* Put the first Key into the ignition Lock, but do NOT switch ON the ignition.
 +
* Press and Hold the Brake Pedal for 20 Seconds to wake up the Diagnostic Databus.
  
  
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[05 - Acc/Start Auth.]'''<br>
 
'''[05 - Acc/Start Auth.]'''<br>
 +
 +
Select Block 024.<br>
 +
'''[Go!]'''<br>
 +
''Make sure the shown lock times in field 1, 2, 3 and 4 are '''0''' (each field represents a time in minutes).''<br>
 +
* ''If the lock times are NOT '''0''':''
 +
** ''Do NOT switch off the ignition!''
 +
** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''
 +
'''[Done, Go Back]'''<br>
  
  

Revision as of 09:48, 19 July 2007

This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer III, where the immobilizer control module is integrated in instrument cluster. See the separate instructions for models where the immobilizer control module is integrated in a separate control module or where the immobilizer control module is integrated in Instrument Cluster.


Determining IMMO-ID & VIN (ECU)

[Select]
[01 - Engine]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Determining IMMO-ID & VIN (Instrument Cluster)

[Select]
[05 - Acc/Start Auth.]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]

---OR---

[Select]
[05 - Acc/Start Auth.]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Instrument Cluster Swapping

Prerequisites:

  • The NEW module is installed in the car.
  • ORIGINAL Electric Steering Lock is still installed.
  • Battery voltage at least 12.0 V.
  • Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) control module.
  • Put the first Key into the ignition Lock, but do NOT switch ON the ignition.
  • Press and Hold the Brake Pedal for 20 Seconds to wake up the Diagnostic Databus.


[Select]
[05 - Acc/Start Auth.]

Select Block 024.
[Go!]
Make sure the shown lock times in field 1, 2, 3 and 4 are 0 (each field represents a time in minutes).

  • If the lock times are NOT 0:
    • Do NOT switch off the ignition!
    • Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.

[Done, Go Back]


[Sec. Access - 16]
For the following procedure, use the PIN of the NEW (USED) control module.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Do it!]


[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the OLD (ORIGINAL) control module.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]


  • Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
  • Verify that the NEW (USED) control module now shows the VIN/IMMO-ID of the vehicle now.