Difference between revisions of "Immobilizer III Key Matching (Kessy)"

From Ross-Tech Wiki
m
m
Line 66: Line 66:
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
  
*''Switch Ignition OFF and remove Key, Steering Lock should engage.''
+
* ''Repeat the following steps until all Keys have been matched:''
*''Insert first Key again and switch Ignition ON.
 
*''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key.''<br>
 
 
 
* ''Repeat the following steps until all keys have been matched:''
 
 
**''Switch Ignition OFF and remove Key, Steering Lock should engage.''
 
**''Switch Ignition OFF and remove Key, Steering Lock should engage.''
**''Insert next Key to Ignition and switch Ignition ON again.''
+
**''Insert the next Key and switch Ignition ON.''
**''The Warning Light for the Immobilizer will light up for ~2 seconds, then go out. Switch Ignition OFF and remove Key.''<br>
+
**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.''
  
'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds.!''
+
'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds!''

Revision as of 05:45, 14 June 2011

This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in a separate immo box. See the separate instructions for models where the immobilizer control module is integrated in instrument cluster or where the immobilizer control module is part of a separate Control Module).

Determining IMMO-ID & VIN

[Select]
[05 - Acc/Start Auth.]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Key Matching

Prerequisites:

  • Battery voltage at least 12.0 V. We strongly recommend the use of a battery charger.
  • You can match up to 8 keys.
  • All keys are either new or were adapted to this car (IMMO-ID) before.
  • While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
  • If all Keys are new OR the first inserted Key is new, the Ignition will NOT switch ON with this key.
    • Put the first Key into the ignition Lock, but do NOT switch ON the ignition.
    • Press and Hold the Brake Pedal for 20 Seconds to wake up the Diagnostic Databus.


[Select]
[05 - Acc/Start Auth.]
[Meas. Blocks - 08]
Select Block 022.
[Go!]
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.


Select Block 023.
[Go!]
Make sure the shown lock times in field 1, 2, 3 and 4 are 0 (each field represents a time in minutes).

  • If the lock times are NOT 0:
    • Do NOT switch off the ignition!
    • Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-4.

[Done, Go Back]


[Sec. Access - 16]
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Do it!]


[Adaptation - 10]
Enter 21 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
The old keys are automatically being cleared.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Repeat the following steps until all Keys have been matched:
    • Switch Ignition OFF and remove Key, Steering Lock should engage.
    • Insert the next Key and switch Ignition ON.
    • The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.

Note: The above steps after saving the adaptation, should not exceed 60 seconds withing matching 2 of the keys and having one key in the ignition should not exceed 30 seconds!