Difference between revisions of "Immobilizer IV Immobilizer Swapping (Instrument Cluster)"
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| Line 24: | Line 24: | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | |||
| + | |||
| + | == Instrument Cluster Swapping (Used Cluster) == | ||
| + | |||
| + | '''<u>Prerequisites:</u>'''<br> | ||
| + | * The new (used) cluster is installed in the car. | ||
| + | * You do have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster. | ||
| + | * Battery voltage at least 12.0 V.<br> | ||
| + | |||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[25 - Immobilizer]'''<br> | ||
| + | |||
| + | |||
| + | '''[Security Access - 16]'''<br> | ||
| + | ''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br> | ||
| + | ''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br> | ||
| + | * '''4-digit PIN''' | ||
| + | ** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.'' | ||
| + | * '''7-digit PIN''' | ||
| + | ** '''[Use 7-digit PIN/SKC]''' | ||
| + | ** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. | ||
| + | ** '''[OK]''' | ||
| + | ** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". | ||
| + | '''[Do it!]'''<br> | ||
| + | |||
| + | |||
| + | '''[Adaptation - 10]'''<br> | ||
| + | Enter 050 in "Channel Number".<br> | ||
| + | '''[Read]'''<br> | ||
| + | ''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br> | ||
| + | ''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br> | ||
| + | * '''4-digit PIN''' | ||
| + | ** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.'' | ||
| + | * '''7-digit PIN''' | ||
| + | ** '''[Use 7-digit PIN/SKC]''' | ||
| + | ** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code. | ||
| + | ** '''[OK]''' | ||
| + | ** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX". | ||
| + | '''[Save]'''<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | |||
| + | |||
| + | * Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again. | ||
| + | * Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now. | ||
Revision as of 09:03, 1 June 2006
This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV.
Determining IMMO-ID & VIN (ECU)
[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Determining IMMO-ID & VIN (Instrument Cluster)
[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Instrument Cluster Swapping (Used Cluster)
Prerequisites:
- The new (used) cluster is installed in the car.
- You do have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
- Battery voltage at least 12.0 V.
[Select]
[25 - Immobilizer]
[Security Access - 16]
For the following procedure, use the PIN of the NEW (USED) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
- 4-digit PIN
- Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
- 7-digit PIN
- [Use 7-digit PIN/SKC]
- Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
- [OK]
- VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Do it!]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the OLD (ORIGINAL) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
- 4-digit PIN
- Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
- 7-digit PIN
- [Use 7-digit PIN/SKC]
- Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
- [OK]
- VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
- Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.