Difference between revisions of "Immobilizer IV Key Matching"

From Ross-Tech Wiki
 
Line 8: Line 8:
 
'''[Meas. Blocks - 08]'''<br>
 
'''[Meas. Blocks - 08]'''<br>
 
Select Block 081.<br>
 
Select Block 081.<br>
 +
'''[Go!]'''<br>
 
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
 
''The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.''.<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
Line 17: Line 18:
 
'''<u>Prerequisites:</u>'''<br>
 
'''<u>Prerequisites:</u>'''<br>
 
* All keys are either new or were adapted to this car (IMMO-ID) before.<br>
 
* All keys are either new or were adapted to this car (IMMO-ID) before.<br>
 +
* You can match up to 8 keys.
 +
* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
 
* Battery voltage at least 12.0 V.<br>
 
* Battery voltage at least 12.0 V.<br>
  
=== # Checking Keys ===
+
 
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[25 - Immobilizer]'''<br>
 
'''[25 - Immobilizer]'''<br>
 
'''[Meas. Blocks - 08]'''<br>
 
'''[Meas. Blocks - 08]'''<br>
 
Select Block 081.<br>
 
Select Block 081.<br>
 +
'''[Go!]'''<br>
 +
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
 +
''You can check each key in this manner.''
 +
 +
 +
Select Block 003.<br>
 +
'''[Go!]'''<br>
 +
''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br>
 +
* ''If the lock times are NOT '''0''':''
 +
** ''Do NOT switch off the ignition!''
 +
** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''
 +
'''[Done, Go Back]'''<br>
  
=== Checking Lock Times ===
 
  
 
'''[Security Access - 16]'''<br>
 
'''[Security Access - 16]'''<br>
Enter 40168, to enable the basic setting.<br>
+
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''
 +
* '''4-digit PIN'''
 +
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
 +
* '''7-digit PIN'''
 +
** '''[Use 7-digit PIN/SKC]'''
 +
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
 +
** '''[OK]'''
 +
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
 
'''[Do it!]'''<br>
 
'''[Do it!]'''<br>
 +
 +
 +
'''[Adaptation - 10]'''<br>
 +
Enter 001 in "Channel Number".<br>
 +
'''[Read]'''<br>
 +
''The "Stored Value" is the number of keys currently matched.''<br>
 +
Enter a "new value" corresponding to the total number of keys to be matched,  including any existing keys.<br>
 +
''The old keys are automatically beeing cleared.''<br>
 +
'''[Save]'''<br>
 +
'''[Done, Go Back]'''
 +
'''[Close Controller, Go Back - 06]'''
 +
 +
 +
* ''Repeat the following steps until all keys have been matched:''<br>
 +
**''Switch ignition off and remove key.''<br>
 +
**''Insert next key to ignition and switch ignition on again.''<br>
 +
**''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.''<br>
 +
 +
'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

Revision as of 08:33, 5 April 2006

This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer IV.

Determining IMMO-ID & VIN

[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Key Matching

Prerequisites:

  • All keys are either new or were adapted to this car (IMMO-ID) before.
  • You can match up to 8 keys.
  • While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
  • Battery voltage at least 12.0 V.


[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.


Select Block 003.
[Go!]
Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).

  • If the lock times are NOT 0:
    • Do NOT switch off the ignition!
    • Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.

[Done, Go Back]


[Security Access - 16]
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Do it!]


[Adaptation - 10]
Enter 001 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
The old keys are automatically beeing cleared.
[Save]
[Done, Go Back] [Close Controller, Go Back - 06]


  • Repeat the following steps until all keys have been matched:
    • Switch ignition off and remove key.
    • Insert next key to ignition and switch ignition on again.
    • The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.

Note: The above steps after saving the adaptation, should not exceed 60 seconds!