Difference between revisions of "Immobilizer I Key Matching (Separate)"

From Ross-Tech Wiki
m (Undo revision 4176 by Sebastian (Talk))
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
__FORCETOC__
 
__FORCETOC__
'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in a separate immo box. See the seperate instructions for models where the [[Immobilizer I Key Matching (Cluster)|immobilizer control module is integrated in instrument cluster]].'''
+
'''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer I, where the immobilizer control module is integrated in a separate immo box. See the seperate instructions for models where the [[Immobilizer I Key Matching (Cluster)|immobilizer control module is integrated in instrument cluster]].'''
  
 
== Determining IMMO-ID & VIN ==
 
== Determining IMMO-ID & VIN ==
Line 6: Line 6:
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[25 - Immobilizer]'''<br>
 
'''[25 - Immobilizer]'''<br>
Look at the first "Extra" field. The 14-digit string in the Immo-ID.<br>
+
Look at the "Component" field. The 14-digit string in the Immo-ID.<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
  
Line 25: Line 25:
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
 
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
 
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
''You can check each key in this manner.''
+
''You can check each key in this manner.''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
  
  
 
'''[Login - 11]'''<br>
 
'''[Login - 11]'''<br>
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''
 
 
* '''4-digit PIN'''
 
* '''4-digit PIN'''
 
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
 
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
* '''7-digit PIN'''
 
** '''[Use 7-digit PIN/SKC]'''
 
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
 
** '''[OK]'''
 
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
 
 
'''[Do it!]'''<br>
 
'''[Do it!]'''<br>
  
Line 46: Line 40:
 
''The "Stored Value" is the number of keys currently matched.''<br>
 
''The "Stored Value" is the number of keys currently matched.''<br>
 
Enter a "new value" corresponding to the total number of keys to be matched,  including any existing keys.<br>
 
Enter a "new value" corresponding to the total number of keys to be matched,  including any existing keys.<br>
''The old keys are automatically beeing cleared.''<br>
+
''The old keys are automatically being cleared.''<br>
 
'''[Save]'''<br>
 
'''[Save]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
  
* ''Repeat the following steps until all keys have been matched:''<br>
+
* ''Repeat the following steps until all Keys have been matched:''
**''Switch ignition off and remove key.''<br>
+
**''Switch Ignition OFF and remove Key.''
**''Insert next key to ignition and switch ignition on again.''<br>
+
**''Insert the next Key and switch Ignition ON.''
**''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.''<br>
+
**''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.''
  
 
'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''
 
'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

Latest revision as of 17:26, 12 July 2012

This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer I, where the immobilizer control module is integrated in a separate immo box. See the seperate instructions for models where the immobilizer control module is integrated in instrument cluster.

Determining IMMO-ID & VIN

[Select]
[25 - Immobilizer]
Look at the "Component" field. The 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]


Key Matching

Prerequisites:

  • All keys are either new or were adapted to this car (IMMO-ID) before.
  • You can match up to 4 keys.
  • While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
  • Battery voltage at least 12.0 V.


[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 001.
[Go!]
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.
[Done, Go Back]


[Login - 11]

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.

[Do it!]


[Adaptation - 10]
Enter 01 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
The old keys are automatically being cleared.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Repeat the following steps until all Keys have been matched:
    • Switch Ignition OFF and remove Key.
    • Insert the next Key and switch Ignition ON.
    • The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out.

Note: The above steps after saving the adaptation, should not exceed 60 seconds!