Difference between revisions of "Readiness - APB Engine Code"

From Ross-Tech Wiki
 
(24 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
=== Manually Generating Readiness ===
 
=== Manually Generating Readiness ===
  
'''<u>Prerequisites:</u>'''
+
 
* Ignition ON and Engine OFF.
+
 
 +
* <u>Ignition ON and Engine <b>OFF</b></u><br>
 +
 
 +
 
 +
 
 +
''Reading and clearing fault codes''<br>
  
 
'''[Select]'''<br>
 
'''[Select]'''<br>
Line 11: Line 16:
  
  
'''<u>Throttle Body Alignment</u>'''<br>
+
''Throttle Body Alignment''<br>
  
 
'''[Measuring Blocks - 08]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
Line 17: Line 22:
 
'''[Go]'''<br>
 
'''[Go]'''<br>
 
'''[Switch to basic settings]'''<br>
 
'''[Switch to basic settings]'''<br>
Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switch to basic settings. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.<br>
+
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
''Transmission kickdown (applies to Auto Trans vehicles only!)''<br>
 +
 
 +
Select group 063<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
'''[Switch to Meas. Blocks]'''<br>
  
  
Channel 000<br>
 
'''[Read]'''<br>
 
'''[Save]'''<br>
 
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back]'''<br>
 +
 +
 +
 +
* <u>Ignition ON and Engine <b>ON</b> at idle</u><br>
 +
 +
 +
''Fuel leakage test''<br>
 +
 +
'''[Select]'''<br>
 +
'''[01 - Engine]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
Block 010 (in 1st Row)<br>
+
Select group 071<br>
Block 011 (in 2nd Row)<br>
+
'''[Go]'''<br>
'''[Go!]'''<br>
+
'''[Switch to basic settings]'''<br>
Check fields 2, specification is '''ADP OK'''.<br>
+
Leave it in Basic Settings until the fourth field reads Syst.OK<br>
* Move the selector lever in position '''D''' and drive with partial load '''20 m / 70 ft''' forward, then brake to standstill.
+
'''[Switch to Meas. Blocks]'''<br>
* Hold the brake for 10 seconds.
+
 
* Move the selector lever in position '''R''' and drive with partial load '''20 m / 70 ft''' reverse, then brake to standstill.
+
 
* Hold the brake for 10 seconds.
+
''Evap purge test''<br>
The procedure needs to be repeated at least 5 times and can be repeated up to 10 times until the measuring values show '''ADP OK'''.<br>
+
 
 +
Select group 070<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads EVAP OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
''A/F control test''<br>
 +
 
 +
Select group 107<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads Syst.OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
* <u>Ignition ON and Engine <b>ON between 1800 and 2200 rpm</b></u><br>
 +
 
 +
 
 +
 
 +
''O2 sensor heater test''<br>
 +
 
 +
Select group 041<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until there are kOhm readings in the first and third fields<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
Select group 042<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until there are kOhm readings in the first and third fields<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
* <u>Ignition ON and Engine <b>ON at idle</b></u><br>
 +
 
 +
 
 +
 
 +
''Post-cat O2 sensors readiness test''<br>
 +
 
 +
Select group 036<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
* <u>Ignition ON and Engine <b>ON between 1520 and 2280 rpm</b></u><br>
 +
 
 +
 
 +
 
 +
''Pre-cat O2 sensors response time test''<br>
 +
 
 +
Select group 034<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads B1-S1 OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
Select group 035<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads B2-S1 OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
* <u>Ignition ON and Engine <b>ON at idle</b></u><br>
 +
 
 +
 
 +
 
 +
''O2 sensor control test''<br>
 +
 
 +
Select group 037<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
Select group 038<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
''Post-cat O2 sensor aging test''<br>
 +
 
 +
Select group 043<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads B1-S2 OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
Select group 044<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads B2-S2 OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
* <u>Ignition ON and Engine <b>ON between 1880 and 2280 rpm</b></u><br>
 +
 
 +
 
 +
 
 +
''Catalytic converter test''<br>
 +
 
 +
Select group 046<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads CAT B1 OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
Select group 047<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads CAT B2 OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
 
 +
 
 +
 
 +
* <u>Ignition ON and Engine <b>ON at idle</b></u><br>
 +
 
 +
 
 +
 
 +
''Secondary air injection test (applies to Auto Trans vehicles only!)''<br>
 +
 
 +
Select group 077<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
Select group 078<br>
 +
'''[Go]'''<br>
 +
'''[Switch to basic settings]'''<br>
 +
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 +
'''[Switch to Meas. Blocks]'''<br>
 +
'''[Done, Go Back]'''<br>
 +
 
 +
 
 +
''Checking Readiness''<br>
 +
'''[Readiness]'''<br>
 +
Make sure none of the fields say Failed or Incomplete<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br><br>
+
'''[Close Controller, Go Back]'''<br>
 +
 
 +
 
 +
 
 +
<i>You're done! </i><br>

Latest revision as of 16:14, 5 October 2006

Manually Generating Readiness

  • Ignition ON and Engine OFF


Reading and clearing fault codes

[Select]
[01 - Engine]
[Fault Codes - 02]
[Clear Codes -05]
[Done, Go Back]


Throttle Body Alignment

[Measuring Blocks - 08]
Select group 060
[Go]
[Switch to basic settings]
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.
[Switch to Meas. Blocks]


Transmission kickdown (applies to Auto Trans vehicles only!)

Select group 063
[Go]
[Switch to basic settings]
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.
[Switch to Meas. Blocks]


[Done, Go Back]
[Close Controller, Go Back]


  • Ignition ON and Engine ON at idle


Fuel leakage test

[Select]
[01 - Engine]
[Measuring Blocks - 08]
Select group 071
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst.OK
[Switch to Meas. Blocks]


Evap purge test

Select group 070
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads EVAP OK
[Switch to Meas. Blocks]


A/F control test

Select group 107
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst.OK
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON between 1800 and 2200 rpm


O2 sensor heater test

Select group 041
[Go]
[Switch to basic settings]
Leave it in Basic Settings until there are kOhm readings in the first and third fields
[Switch to Meas. Blocks]
Select group 042
[Go]
[Switch to basic settings]
Leave it in Basic Settings until there are kOhm readings in the first and third fields
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON at idle


Post-cat O2 sensors readiness test

Select group 036
[Go]
[Switch to basic settings]
Leave it in Basic Settings until you see B1-S2 OK in the first field and B2-S2 OK in the third field
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON between 1520 and 2280 rpm


Pre-cat O2 sensors response time test

Select group 034
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads B1-S1 OK
[Switch to Meas. Blocks]
Select group 035
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads B2-S1 OK
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON at idle


O2 sensor control test

Select group 037
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Switch to Meas. Blocks]
Select group 038
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Switch to Meas. Blocks]


Post-cat O2 sensor aging test

Select group 043
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads B1-S2 OK
[Switch to Meas. Blocks]
Select group 044
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads B2-S2 OK
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON between 1880 and 2280 rpm


Catalytic converter test

Select group 046
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads CAT B1 OK
[Switch to Meas. Blocks]
Select group 047
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads CAT B2 OK
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON at idle


Secondary air injection test (applies to Auto Trans vehicles only!)

Select group 077
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Switch to Meas. Blocks]
Select group 078
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Switch to Meas. Blocks]
[Done, Go Back]


Checking Readiness
[Readiness]
Make sure none of the fields say Failed or Incomplete
[Done, Go Back]
[Close Controller, Go Back]


You're done!