Difference between revisions of "Readiness - APB Engine Code-without-MB"

From Ross-Tech Wiki
 
(11 intermediate revisions by the same user not shown)
Line 2: Line 2:
  
 
Important: This procedure calls for the use of the Basic Settings function in several different groups. It is not advisable to scroll between groups in Basic Settings since you may go into groups that have an undesired effect. Instead, it is HIGHLY recommended that you manually enter in the next group number and hit '''[Go]''' instead of scrolling.<br>
 
Important: This procedure calls for the use of the Basic Settings function in several different groups. It is not advisable to scroll between groups in Basic Settings since you may go into groups that have an undesired effect. Instead, it is HIGHLY recommended that you manually enter in the next group number and hit '''[Go]''' instead of scrolling.<br>
 
 
* Turn the ignition swith on but do <b>NOT</b> start the engine <br>
 
 
  
  
 
<ol>
 
<ol>
   <li>''Reading and clearing fault codes''
+
* <u>Turn the ignition switch on but do <b>NOT</b> start the engine</u> <br>
 +
<br>
 +
   <li>''Reading and clearing fault codes''<br>
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[01 - Engine]'''<br>
 
'''[01 - Engine]'''<br>
Line 16: Line 14:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
<br>
 
<br>
 +
 
<li>''Throttle Body Alignment''<br>
 
<li>''Throttle Body Alignment''<br>
 
'''[Basic Settings - 04]'''<br>
 
'''[Basic Settings - 04]'''<br>
Line 22: Line 21:
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
<br>
 
<br>
 +
 
<li>''Transmission kickdown <u>(applies to Auto Trans vehicles only!)</u>''<br>
 
<li>''Transmission kickdown <u>(applies to Auto Trans vehicles only!)</u>''<br>
 
Select group 063<br>
 
Select group 063<br>
Line 27: Line 27:
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
<br>
 
<br>
 +
 
<li>'''[Done, Go Back]'''<br>
 
<li>'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back]'''<br>
 
'''[Close Controller, Go Back]'''<br>
Line 32: Line 33:
 
* <u>Start engine and let it idle</u><br>
 
* <u>Start engine and let it idle</u><br>
 
<br>
 
<br>
 +
 
<li>''Fuel leakage test''<br>
 
<li>''Fuel leakage test''<br>
 
'''[Select]'''<br>
 
'''[Select]'''<br>
Line 40: Line 42:
 
Leave it in this group until the fourth field reads Syst.OK<br>
 
Leave it in this group until the fourth field reads Syst.OK<br>
 
<br>
 
<br>
 +
 
<li>''Evap purge test''<br>
 
<li>''Evap purge test''<br>
 
Select group 070<br>
 
Select group 070<br>
Line 45: Line 48:
 
Leave it in this group until the fourth field reads EVAP OK<br>
 
Leave it in this group until the fourth field reads EVAP OK<br>
 
<br>
 
<br>
 +
 
<li>''A/F control test''<br>
 
<li>''A/F control test''<br>
 
Select group 107<br>
 
Select group 107<br>
Line 52: Line 56:
 
* <u>Increase and hold engine speed between <b>1800 and 2200 rpm</b></u><br>
 
* <u>Increase and hold engine speed between <b>1800 and 2200 rpm</b></u><br>
 
<br>
 
<br>
 +
 
<li>''O2 sensor heater test''<br>
 
<li>''O2 sensor heater test''<br>
 
Select group 041<br>
 
Select group 041<br>
Line 62: Line 67:
 
* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>
 
* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>
 
<br>
 
<br>
 +
 
<li>''Post-cat O2 sensors readiness test''<br>
 
<li>''Post-cat O2 sensors readiness test''<br>
 
Select group 036<br>
 
Select group 036<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
 
Leave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>
 
Leave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>
 
+
<br>
 
 
 
 
 
* <u>Increase and hold engine speed between between <b>1520 and 2280 rpm</b></u><br>
 
* <u>Increase and hold engine speed between between <b>1520 and 2280 rpm</b></u><br>
 
+
<br>
 
 
  
 
<li>''Pre-cat O2 sensors response time test''<br>
 
<li>''Pre-cat O2 sensors response time test''<br>
 
+
<br>
 
Select group 034<br>
 
Select group 034<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
Line 81: Line 84:
 
'''[Go]'''<br>
 
'''[Go]'''<br>
 
Leave it in this group until the fourth field reads B2-S1 OK<br>
 
Leave it in this group until the fourth field reads B2-S1 OK<br>
 
+
<br>
 
 
 
 
 
* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>
 
* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>
 
+
<br>
 
 
  
 
<li>''O2 sensor control test''<br>
 
<li>''O2 sensor control test''<br>
 
 
Select group 037<br>
 
Select group 037<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
Line 96: Line 95:
 
'''[Go]'''<br>
 
'''[Go]'''<br>
 
Leave it in this group until the fourth field reads Syst. OK<br>
 
Leave it in this group until the fourth field reads Syst. OK<br>
 
+
<br>
 
 
  
 
<li>''Post-cat O2 sensor aging test''<br>
 
<li>''Post-cat O2 sensor aging test''<br>
 
 
Select group 043<br>
 
Select group 043<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
Line 107: Line 104:
 
'''[Go]'''<br>
 
'''[Go]'''<br>
 
Leave it in this group until the fourth field reads B2-S2 OK<br>
 
Leave it in this group until the fourth field reads B2-S2 OK<br>
 
+
<br>
 
 
 
 
 
* <u>Increase and hold engine speed between between <b>1880 and 2280 rpm</b></u><br>
 
* <u>Increase and hold engine speed between between <b>1880 and 2280 rpm</b></u><br>
 
+
<br>
 
 
  
 
<li>''Catalytic converter test''<br>
 
<li>''Catalytic converter test''<br>
 
 
Select group 046<br>
 
Select group 046<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
Line 122: Line 115:
 
'''[Go]'''<br>
 
'''[Go]'''<br>
 
Leave it in this group until the fourth field reads CAT B2 OK<br>
 
Leave it in this group until the fourth field reads CAT B2 OK<br>
 
+
<br>
 
 
 
 
 
* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>
 
* <u>Take your foot off the accelerator and allow the engine to <b>idle</b></u><br>
 
+
<br>
 
 
  
 
<li>''Secondary air injection test (applies to Auto Trans vehicles only!)''<br>
 
<li>''Secondary air injection test (applies to Auto Trans vehicles only!)''<br>
 
 
Select group 077<br>
 
Select group 077<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
Line 138: Line 127:
 
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
+
<br>
  
 
<li>''Checking Readiness''<br>
 
<li>''Checking Readiness''<br>
Line 146: Line 135:
 
'''[Close Controller, Go Back]'''<br>
 
'''[Close Controller, Go Back]'''<br>
 
</ol>
 
</ol>
 
+
<br>
 
 
 
<i>You're done! </i><br>
 
<i>You're done! </i><br>

Latest revision as of 11:14, 6 October 2006

Manually Generating Readiness

Important: This procedure calls for the use of the Basic Settings function in several different groups. It is not advisable to scroll between groups in Basic Settings since you may go into groups that have an undesired effect. Instead, it is HIGHLY recommended that you manually enter in the next group number and hit [Go] instead of scrolling.


    • Turn the ignition switch on but do NOT start the engine

  1. Reading and clearing fault codes
    [Select]
    [01 - Engine]
    [Fault Codes - 02]
    [Clear Codes -05]
    [Done, Go Back]

  2. Throttle Body Alignment
    [Basic Settings - 04]
    Select group 060
    [Go]
    Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.

  3. Transmission kickdown (applies to Auto Trans vehicles only!)
    Select group 063
    [Go]
    Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.

  4. [Done, Go Back]
    [Close Controller, Go Back]

    • Start engine and let it idle

  5. Fuel leakage test
    [Select]
    [01 - Engine]
    [Basic Settings - 04]
    Select group 071
    [Go]
    Leave it in this group until the fourth field reads Syst.OK

  6. Evap purge test
    Select group 070
    [Go]
    Leave it in this group until the fourth field reads EVAP OK

  7. A/F control test
    Select group 107
    [Go]
    Leave it in this group until the fourth field reads Syst.OK

    • Increase and hold engine speed between 1800 and 2200 rpm

  8. O2 sensor heater test
    Select group 041
    [Go]
    Leave it in this group until there are kOhm readings in the first and third fields
    Select group 042
    [Go]
    Leave it in this group until there are kOhm readings in the first and third fields

    • Take your foot off the accelerator and allow the engine to idle

  9. Post-cat O2 sensors readiness test
    Select group 036
    [Go]
    Leave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field

    • Increase and hold engine speed between between 1520 and 2280 rpm

  10. Pre-cat O2 sensors response time test

    Select group 034
    [Go]
    Leave it in this group until the fourth field reads B1-S1 OK
    Select group 035
    [Go]
    Leave it in this group until the fourth field reads B2-S1 OK

    • Take your foot off the accelerator and allow the engine to idle

  11. O2 sensor control test
    Select group 037
    [Go]
    Leave it in this group until the fourth field reads Syst. OK
    Select group 038
    [Go]
    Leave it in this group until the fourth field reads Syst. OK

  12. Post-cat O2 sensor aging test
    Select group 043
    [Go]
    Leave it in this group until the fourth field reads B1-S2 OK
    Select group 044
    [Go]
    Leave it in this group until the fourth field reads B2-S2 OK

    • Increase and hold engine speed between between 1880 and 2280 rpm

  13. Catalytic converter test
    Select group 046
    [Go]
    Leave it in this group until the fourth field reads CAT B1 OK
    Select group 047
    [Go]
    Leave it in this group until the fourth field reads CAT B2 OK

    • Take your foot off the accelerator and allow the engine to idle

  14. Secondary air injection test (applies to Auto Trans vehicles only!)
    Select group 077
    [Go]
    Leave it in this group until the fourth field reads Syst. OK
    Select group 078
    [Go]
    Leave it in Basic Settings until the fourth field reads Syst. OK
    [Done, Go Back]

  15. Checking Readiness
    [Readiness]
    Make sure none of the fields say Failed or Incomplete
    [Done, Go Back]
    [Close Controller, Go Back]


You're done!