Difference between revisions of "Readiness - APB Engine Code-without-MB"

From Ross-Tech Wiki
Line 1: Line 1:
 
=== Manually Generating Readiness ===
 
=== Manually Generating Readiness ===
  
 
+
Important: This procedure calls for the use of the Basic Settings function in several different groups. It is not advisable to scroll between groups in Basic Settings since you may go into groups that have an undesired effect. Instead, it is HIGHLY recommended that you manually enter in the next group number and hit '''[Go]''' instead of scrolling.<br>
  
 
* <u>Ignition ON and Engine <b>OFF</b></u><br>
 
* <u>Ignition ON and Engine <b>OFF</b></u><br>
Line 128: Line 128:
 
Select group 044<br>
 
Select group 044<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
Leave it in Basic Settings until the fourth field reads B2-S2 OK<br>
+
Leave it in this group until the fourth field reads B2-S2 OK<br>
  
  
Line 140: Line 140:
 
Select group 046<br>
 
Select group 046<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads CAT B1 OK<br>
Leave it in Basic Settings until the fourth field reads CAT B1 OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
 
Select group 047<br>
 
Select group 047<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads CAT B2 OK<br>
Leave it in Basic Settings until the fourth field reads CAT B2 OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 159: Line 155:
 
Select group 077<br>
 
Select group 077<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads Syst. OK<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
 
Select group 078<br>
 
Select group 078<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
 
 
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
'''[Switch to Meas. Blocks]'''<br>
 
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
  

Revision as of 08:19, 6 October 2006

Manually Generating Readiness

Important: This procedure calls for the use of the Basic Settings function in several different groups. It is not advisable to scroll between groups in Basic Settings since you may go into groups that have an undesired effect. Instead, it is HIGHLY recommended that you manually enter in the next group number and hit [Go] instead of scrolling.

  • Ignition ON and Engine OFF


Reading and clearing fault codes

[Select]
[01 - Engine]
[Fault Codes - 02]
[Clear Codes -05]
[Done, Go Back]


Throttle Body Alignment

[Basic Settings - 04]
Select group 060
[Go]
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.


Transmission kickdown (applies to Auto Trans vehicles only!)

Select group 063
[Go]
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.


[Done, Go Back]
[Close Controller, Go Back]


  • Ignition ON and Engine ON at idle


Fuel leakage test

[Select]
[01 - Engine]
[Basic Settings - 04]
Select group 071
[Go]
Leave it in this group until the fourth field reads Syst.OK


Evap purge test

Select group 070
[Go]
Leave it in this group until the fourth field reads EVAP OK


A/F control test

Select group 107
[Go]
Leave it in this group until the fourth field reads Syst.OK


  • Ignition ON and Engine ON between 1800 and 2200 rpm


O2 sensor heater test

Select group 041
[Go]
Leave it in this group until there are kOhm readings in the first and third fields
Select group 042
[Go]
Leave it in this group until there are kOhm readings in the first and third fields


  • Ignition ON and Engine ON at idle


Post-cat O2 sensors readiness test

Select group 036
[Go]
Leave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field


  • Ignition ON and Engine ON between 1520 and 2280 rpm


Pre-cat O2 sensors response time test

Select group 034
[Go]
Leave it in this group until the fourth field reads B1-S1 OK
Select group 035
[Go]
Leave it in this group until the fourth field reads B2-S1 OK


  • Ignition ON and Engine ON at idle


O2 sensor control test

Select group 037
[Go]
Leave it in this group until the fourth field reads Syst. OK
Select group 038
[Go]
Leave it in this group until the fourth field reads Syst. OK


Post-cat O2 sensor aging test

Select group 043
[Go]
Leave it in this group until the fourth field reads B1-S2 OK
Select group 044
[Go]
Leave it in this group until the fourth field reads B2-S2 OK


  • Ignition ON and Engine ON between 1880 and 2280 rpm


Catalytic converter test

Select group 046
[Go]
Leave it in this group until the fourth field reads CAT B1 OK
Select group 047
[Go]
Leave it in this group until the fourth field reads CAT B2 OK


  • Ignition ON and Engine ON at idle


Secondary air injection test (applies to Auto Trans vehicles only!)

Select group 077
[Go]
Leave it in this group until the fourth field reads Syst. OK
Select group 078
[Go]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Done, Go Back]


Checking Readiness
[Readiness]
Make sure none of the fields say Failed or Incomplete
[Done, Go Back]
[Close Controller, Go Back]


You're done!