Ross-Tech Wiki - Recent changes [en]

02861

Dana — Sat, 04 Sep 2010 03:35:38 GMT

← Older revision		Revision as of 03:35, 4 September 2010
(2 intermediate revisions not shown)
Line 21:		Line 21:
	==== Special Notes ====		==== Special Notes ====

-	* When found in VW Passat (3C), the Electronic Steering Column Lock ~~Control Module~~ (J764) ~~cannot be replaced individually and~~ the entire ~~Steering Column need to be replaced as well~~. ~~If the Steering Column needs to be replaced the~~ Comfort Control Module (J393) ~~needs to be replaced too since it~~ houses the Immobilizer related Functions. ~~See TPI 2018893 for further details~~.	+	* When found in the VW Passat (3C), it might be possible to replace the Electronic Steering Column Lock (J764) separately from the entire steering column.
		+	** The Comfort Control Module (J393) houses the Immobilizer related Functions. Depending on the Comfort Control Module, it might be possible to reprogram it as opposed to replacing it with the ESCL replacement. At this time we consider this immobilizer system repair Not Supported with VCDS. Generally immobilizer repairs on the VW Passat (3C) are performed at the VW Dealer using their GEKO system.

	[[Category:Fault Codes]]		[[Category:Fault Codes]]

17884/P1476/005238

Sebastian — Wed, 01 Sep 2010 22:42:16 GMT

Created page with '== 17884/P1476/005238 - EVAP Leak Detection Pump: Malfunction / Insufficient Vacuum == ==== Possible Symptoms ==== * Malfunction Indicator Light (MIL) ON ==== Possible Causes…'

New page

== 17884/P1476/005238 - EVAP Leak Detection Pump: Malfunction / Insufficient Vacuum ==

==== Possible Symptoms ====

* Malfunction Indicator Light (MIL) ON

==== Possible Causes ====

* Evaporative Emission (EVAP) System faulty/leaking
* Evaporative Emission (EVAP) Leak Detection Pump faulty

==== Possible Solutions ====

* Check Evaporative Emission (EVAP) System for Leaks
* Check Evaporative Emission (EVAP) Leak Detection Pump

__FORCETOC__
[[Category:Fault Codes]]

VW Tiguan (5N) Parking Brake

Dana — Wed, 01 Sep 2010 16:37:54 GMT

← Older revision		Revision as of 16:37, 1 September 2010
Line 2:		Line 2:

	== Coding ==		== Coding ==
		+
		+	Note: When replacing this Parking Brake Control Module it is necessary to save a complete Auto-Scan before repairs. The [[VW Tiguan (5N) Brake Electronics\|ABS Module]] coding will be lost when the Parking Brake Module is replaced and you you MUST have a record of the existing coding or you won't be able re-code the ABS module!''<br>
		+

	* 0000056 = Parking Brake without Auto-Hold (Rest of World / PR-UH1)<br>		* 0000056 = Parking Brake without Auto-Hold (Rest of World / PR-UH1)<br>

VW Passat (3C) Parking Brake

Dana — Wed, 01 Sep 2010 16:37:44 GMT

← Older revision		Revision as of 16:37, 1 September 2010
(2 intermediate revisions not shown)
Line 2:		Line 2:

	== Coding ==		== Coding ==
		+	Note: When replacing this Parking Brake Control Module it is necessary to save a complete Auto-Scan before repairs. The [[VW Passat (3C) Brake Electronics\|ABS Module]] coding will be lost when the Parking Brake Module is replaced and you you MUST have a record of the existing coding or you won't be able re-code the ABS module!''<br>
		+

	* 0000010 = Parking Brake without Auto-Hold (North America)<br>		* 0000010 = Parking Brake without Auto-Hold (North America)<br>

Audi A6 (4F) Parking Brake

Dana — Wed, 01 Sep 2010 15:35:59 GMT

← Older revision		Revision as of 15:35, 1 September 2010
Line 33:		Line 33:
	=== Open Rear Parking Brake ===		=== Open Rear Parking Brake ===
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
-	* Connect a battery charger.	+	* Connect a battery charger. See [[#Special Notes\|Special Notes]]
	* Cycle the Parking Brake ON, then OFF first.		* Cycle the Parking Brake ON, then OFF first.
	'''[Select]'''<br>		'''[Select]'''<br>
Line 50:		Line 50:
	=== Close Rear Parking Brake ===		=== Close Rear Parking Brake ===
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
-	* Connect a battery charger.	+	* Connect a battery charger. See [[#Special Notes\|Special Notes]]
	'''[Select]'''<br>		'''[Select]'''<br>
	'''[53 - Parking Brake]'''<br>		'''[53 - Parking Brake]'''<br>
Line 100:		Line 100:

	* [[Audi A6 (4F) Parking Brake Pad Replacement\|Parking Brake Pad Replacement]]		* [[Audi A6 (4F) Parking Brake Pad Replacement\|Parking Brake Pad Replacement]]
		+
		+	==== Special Notes ====
		+
		+	* On vehicles using a separate battery management control module, make sure the charger is connected properly. The proper procedure should be found in the repair manual.
		+	** Attaching the charger directly to the positive and negative terminals of the battery is Not correct. The battery management module will not see the current flow and shut off power to other modules. This can cause damage to various control modules including the [53] - Parking Brake module.

Audi Q7 (4L) Brake Electronics

Sebastian — Tue, 31 Aug 2010 22:34:35 GMT

← Older revision		Revision as of 22:34, 31 August 2010
Line 1:		Line 1:
-	== ~~Basic Setting~~ ==	+	== Coding ==

		+	'''If the old Control Module is still accessible read/copy it's Coding to the new Module. In case this is not possible please [http://www.ross-tech.com/contact.html contact us directly] and we will assist you with the Coding Process.
		+
		+	''Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure the Auto-Scan includes the complete VIN of the vehicle in question.''<br> <br> <br>
		+
		+
		+	== Basic Setting ==
	=== Sensor for Steering Angle (G85) ===		=== Sensor for Steering Angle (G85) ===

Audi Q7 (4L) Brake Electronics

Dana — Tue, 31 Aug 2010 20:09:19 GMT

Created page with '== Basic Setting == === Sensor for Steering Angle (G85) === '''Prerequisites:''' * Start the vehicle. * Turn the steering wheel one turn to the right and one turn to…'

New page

== Basic Setting ==

=== Sensor for Steering Angle (G85) ===

'''Prerequisites:''' 
* Start the vehicle.
* Turn the steering wheel one turn to the right and one turn to the left.
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
* Ensure that the steering wheel is not moved again.
* Keep the engine running and do not switch off the ignition.
* System voltage at least 12.0 V

'''[Select]''' 
'''[03 - Brake Electronics]''' 
'''[Security Access - 16]''' 
Enter 40168, to enable the basic setting. 
'''[Do it!]''' 
'''[Basic Settings - 04]''' 
Group 060 
'''[Go!]''' 
Activate the Basic Setting. 
'''[ON/OFF/Next]''' 
After a successful basic setting, field 2 should say "OK". 
'''[Done, Go Back]''' 
To make sure the basic setting was succesful, check the sensor again. 
'''[Measuring Blocks - 08]''' 
Group 004 
'''[Go!]''' 
Check field 1, the value has to be between -1.5 and +1.5 °. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]'''