Difference between revisions of "Trailer Hitch Retrofitting (5N)"

From Ross-Tech Wiki
(New page: __FORCETOC__ == CAN-Gateway == '''[Select]'''<br> '''[19 - CAN-Gateway]'''<br> '''[Coding - 07]'''<br> '''[Long Coding Helper]'''<br> ** Set ''Byte 03 Bit 6 = [69] Trailer'' active.<br> '...)
 
Line 1: Line 1:
__FORCETOC__
+
''These instructions may not cover mechanical/electronic details, they will only list the the diagnostic side (coding etc.). Additional details for the mechanical/electronic work needed are part of the retrofitting instructions provided by the parts supplier (i.e. trailer hitch retrofits) or can be found in the factory repair manuals and wiring diagrams.''
== CAN-Gateway ==
 
  
'''[Select]'''<br>
 
'''[19 - CAN-Gateway]'''<br>
 
'''[Coding - 07]'''<br>
 
'''[Long Coding Helper]'''<br>
 
** Set ''Byte 03 Bit 6 = [69] Trailer'' active.<br>
 
'''[Do It!]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
  
 +
== Installation & Wiring ==
  
== Trailer Control Module ==
+
Information regarding the Installation can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit.
  
'''''NOTE:''' This part varies depending on the type of the trailer control module. There are 2 variants available, those which are diagnostic capable and those who are not''
 
  
 +
== Configuration ==
  
'''''Variant #1:''' ''Trailer Control Module (#69) NOT diagnostic capable''
+
The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use.
  
Nothing to do here, so leave it alone.
+
* '''Update the Installation List in the Gateway (J533 / #19).'''
 +
** Register the newly added '''69 - Trailer''' Control Module.
 +
* '''Update the Trailer Control Module (J345 / #69) Coding.'''
 +
** Not all Retrofitting Kits contain Diagnostic capable Trailer Control Modules, some Aftermarket Modules may even be pre-coded. This Step can be ignored for Modules which are not Diagnostic capable.
 +
** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS. If an Aftermarket Module is installed, check the Retrofitting Kit for further Instructions.''
 +
* '''Update the Engine Control Module (J623 / #01) Coding.'''
 +
** Make sure that the '''Engine is NOT running''', otherwise the new Coding will be rejected. Models equipped with Start/Stop System do have a Shutoff Switch/Button which will deactivate the Start/Stop Function.
 +
** As a Rule of Thumb, If the Engine uses conventional Short Coding (Coding is 7-digits like 0011312) the Long Codding Assistant does NOT apply. Modules using Short Coding typically do NOT support or require Trailer Configuration Coding. If the Engine Control Module uses a Long Coding the Activation is done in (Long) Coding itself through via Coding Assist. Please also note that there are different Coding Variants for Long Coding.
 +
** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.''
 +
* '''Update the Parking Aid (J446 / #76) OR Parking Aid 2 (J446 / #10) Configuration, if installed.'''
 +
** Depending the exact Model/Model Year either Coding or Adaptation can be used.
 +
** ''Due to different Control Modules and Equipment in the Car the actual Setting is not documented here but will automatically be shown once you access the Coding/Adaptation Function using VCDS. A Security Access may be necessary prior to Coding the Module.''
 +
* '''Update the Rear View Camera (J772 / #6C) Coding, if installed.'''
 +
** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.''
  
'''''Variant #2:''' ''Trailer Control Module (#69) diagnostic capable''
 
  
This control module requires a coding, see VAG-COM coding help or vehicle specific [[Diagnostic Procedures|diagnostic procedures]] for details.
+
'''''If you are having trouble finding/calculating the proper Coding using the Long Coding Assist [http://ross-tech.com/contact.html please Contact us directly].''' Make sure to include a complete Diagnostic Protocol (Auto-Scan) from the Car and state which steps/work you have performed yet.''
 
+
__NOTOC__
 
 
== Parking Aid ==
 
 
 
This control module needs to be recoded, see VAG-COM coding help or vehicle specific [[Diagnostic Procedures|diagnostic procedures]] for details.
 
 
 
 
 
== Engine ==
 
 
 
Normally there is no activation of the trailer hitch in the ECU necessary, however the following engines require to be recoded:
 
 
 
* [[2.0l TFSI (AXX/BGB/BPJ/BPY/BWA)|2.0l TFSI]]
 

Revision as of 05:11, 3 August 2012

These instructions may not cover mechanical/electronic details, they will only list the the diagnostic side (coding etc.). Additional details for the mechanical/electronic work needed are part of the retrofitting instructions provided by the parts supplier (i.e. trailer hitch retrofits) or can be found in the factory repair manuals and wiring diagrams.


Installation & Wiring

Information regarding the Installation can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit.


Configuration

The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use.

  • Update the Installation List in the Gateway (J533 / #19).
    • Register the newly added 69 - Trailer Control Module.
  • Update the Trailer Control Module (J345 / #69) Coding.
    • Not all Retrofitting Kits contain Diagnostic capable Trailer Control Modules, some Aftermarket Modules may even be pre-coded. This Step can be ignored for Modules which are not Diagnostic capable.
    • Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS. If an Aftermarket Module is installed, check the Retrofitting Kit for further Instructions.
  • Update the Engine Control Module (J623 / #01) Coding.
    • Make sure that the Engine is NOT running, otherwise the new Coding will be rejected. Models equipped with Start/Stop System do have a Shutoff Switch/Button which will deactivate the Start/Stop Function.
    • As a Rule of Thumb, If the Engine uses conventional Short Coding (Coding is 7-digits like 0011312) the Long Codding Assistant does NOT apply. Modules using Short Coding typically do NOT support or require Trailer Configuration Coding. If the Engine Control Module uses a Long Coding the Activation is done in (Long) Coding itself through via Coding Assist. Please also note that there are different Coding Variants for Long Coding.
    • Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.
  • Update the Parking Aid (J446 / #76) OR Parking Aid 2 (J446 / #10) Configuration, if installed.
    • Depending the exact Model/Model Year either Coding or Adaptation can be used.
    • Due to different Control Modules and Equipment in the Car the actual Setting is not documented here but will automatically be shown once you access the Coding/Adaptation Function using VCDS. A Security Access may be necessary prior to Coding the Module.
  • Update the Rear View Camera (J772 / #6C) Coding, if installed.
    • Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.


If you are having trouble finding/calculating the proper Coding using the Long Coding Assist please Contact us directly. Make sure to include a complete Diagnostic Protocol (Auto-Scan) from the Car and state which steps/work you have performed yet.