Difference between revisions of "User:Peter"

From Ross-Tech Wiki
Line 1: Line 1:
−
=== Electronic Damping Control J250 - Basic Settings ===
+
 
 +
 
 +
== Basic Settings of the Active/Dynamic Steering == 
 +
 
 +
 
 +
=== 1B-Active Steering ===
  
  
Line 7: Line 12:
 
* Vehicle is lifted off the ground, on a suitable vehicle lift'''<br>
 
* Vehicle is lifted off the ground, on a suitable vehicle lift'''<br>
  
 +
* Perform G85-Steering Angle Sensor Basic Settings found on this Ross-Tech wiki page:
 +
 +
http://wiki.ross-tech.com/wiki/index.php/Audi_A5_%288T%29_Steering_Wheel_Electronics#Basic_Setting
 +
 +
 +
 +
'''- Continue only after successfully completing the G85 basic settings:'''
 +
  
 
'''[Select]'''<br>
 
'''[Select]'''<br>
−
'''[14 - Susp. Elect]'''<br>
+
'''[1B-Active Steering]'''<br>
−
'''[Meas. Blocks - 08]'''<br>
+
 
−
Note: The values stored in the Measuring Value Blocks below are the Minimum and Maximum sensor values.'''<br>
 
−
* Group-054 Field-1 = G78 - Min value'''<br>
 
−
* Group-054 Field-2 = G78 - Max value'''<br>
 
−
<br>
 
−
* Group-055 Field-1 = G289 - Min value'''<br>
 
−
* Group-055 Field-2 = G289 - Max value'''<br>
 
−
<br>
 
−
'''Look at:'''<br>
 
−
'''Group-003 - Field-1,2,3 -  Actual Sensor values'''<br>
 
−
*  If the values are with in the range of the Min - Max stored values from MVBs 054 and 055 then Basic settings can be performed, if not inspect suspension or sensors.'''<br>
 
−
<br>
 
 
'''[Security Access - 16]'''<br>
 
'''[Security Access - 16]'''<br>
−
Enter 31564, to enable the basic setting.'''<br>
+
Enter 61378, to enable the basic setting.'''<br>
 
'''[Do it!]'''<br>
 
'''[Do it!]'''<br>
 +
 +
 
'''[Basic Settings - 04]'''<br>
 
'''[Basic Settings - 04]'''<br>
−
Group 001<br>
+
Group 101<br>
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
−
<br>
+
'''[ON/OFF/Next]''' <br>
−
The New values should be displayed.'''<br>
+
 
−
*  To check the learned values, check Measuring Value Group-008.'''<br>
+
* The results should be stored after a key cycle and fault code(s) should clear.
−
'''[Meas. Blocks - 08]'''<br>
+
 
−
Group 008<br>
+
 
−
'''[Go!]'''<br>
+
'''[Done, Go Back]''' <br>
−
The values displayed should be the learned values as displayed in the Basic Settings window.'''<br>
+
'''[Fault Codes - 02]'''<br>
 +
Check and clear fault codes.<br>
 +
'''[Close Controller, Go Back - 06]'''<br>

Revision as of 10:00, 3 June 2013


Basic Settings of the Active/Dynamic Steering

1B-Active Steering

Prerequisites:

  • Perform G85-Steering Angle Sensor Basic Settings found on this Ross-Tech wiki page:

http://wiki.ross-tech.com/wiki/index.php/Audi_A5_%288T%29_Steering_Wheel_Electronics#Basic_Setting


- Continue only after successfully completing the G85 basic settings:


[Select]
[1B-Active Steering]

[Security Access - 16]
Enter 61378, to enable the basic setting.
 [Do it!]


[Basic Settings - 04]
Group 101
[Go!]
[ON/OFF/Next]

  • The results should be stored after a key cycle and fault code(s) should clear.


[Done, Go Back]
[Fault Codes - 02]
Check and clear fault codes.
[Close Controller, Go Back - 06]

Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=User:Peter&oldid=7107"