Difference between revisions of "VW Golf (1J) Brake Electronics (MK20)"

From Ross-Tech Wiki
 
(7 intermediate revisions by 3 users not shown)
Line 2: Line 2:
  
 
== Coding ==
 
== Coding ==
=== Audi ===
+
* Due to all of the Coding MK20 variants, it is recommended to use the coding from the original module when replacing the ABS module. Save the complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] before repairs.
*No information at this time, email Ross Tech Support.
+
* If you are having trouble finding/calculating the proper Coding please:
 +
** Refer to the [http://wiki.ross-tech.com/wiki/index.php/Official_Factory_Repair_Information  Factory Repair Manual] for Coding information.
 +
** Registered users that need assistance configuring the Coding can send the before and after replacement Auto-Scans to [mailto:Support@Ross-Tech.com Support] for assistance.
  
=== Volkswagen ===
 
 
* ABS = 03504
 
* ABS/EDL = 13504
 
* ABS/EDL/ASR = 13204
 
  
 
== Basic Setting ==
 
== Basic Setting ==
Line 35: Line 32:
 
After a successful basic setting, field 2 should say "OK".<br>
 
After a successful basic setting, field 2 should say "OK".<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
+
To make sure the basic setting was successful, check the sensor again.<br>
 
'''[Measuring Blocks - 08]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
 
Group 004<br>
 
Group 004<br>
Line 42: Line 39:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
  
 
=== Lateral Acceleration Sensor (G200) ===
 
=== Lateral Acceleration Sensor (G200) ===
Line 66: Line 62:
 
After a successful basic setting, field 2 should say "OK".<br>
 
After a successful basic setting, field 2 should say "OK".<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
+
To make sure the basic setting was successful, check the sensor again.<br>
 
'''[Measuring Blocks - 08]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
 
Group 004<br>
 
Group 004<br>
Line 73: Line 69:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
  
 
=== Brake Pressure Sensor 1 (G201) ===
 
=== Brake Pressure Sensor 1 (G201) ===
Line 92: Line 87:
 
After a successful basic setting, field 2 should say "OK".<br>
 
After a successful basic setting, field 2 should say "OK".<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
+
To make sure the basic setting was successful, check the sensor again.<br>
 
'''[Measuring Blocks - 08]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
 
Group 005<br>
 
Group 005<br>
Line 99: Line 94:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
  
 
=== Longitudinal Acceleration Sensor (G251) ===
 
=== Longitudinal Acceleration Sensor (G251) ===
Line 118: Line 112:
 
After a successful basic setting, field 2 should say "OK".<br>
 
After a successful basic setting, field 2 should say "OK".<br>
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
+
To make sure the basic setting was successful, check the sensor again.<br>
 
'''[Measuring Blocks - 08]'''<br>
 
'''[Measuring Blocks - 08]'''<br>
 
Group 006<br>
 
Group 006<br>
Line 125: Line 119:
 
'''[Done, Go Back]'''<br>
 
'''[Done, Go Back]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
'''[Close Controller, Go Back - 06]'''<br>
 
  
 
== Special Procedures ==
 
== Special Procedures ==

Latest revision as of 14:15, 16 August 2017


Coding

  • Due to all of the Coding MK20 variants, it is recommended to use the coding from the original module when replacing the ABS module. Save the complete Auto-Scan before repairs.
  • If you are having trouble finding/calculating the proper Coding please:
    • Refer to the Factory Repair Manual for Coding information.
    • Registered users that need assistance configuring the Coding can send the before and after replacement Auto-Scans to Support for assistance.


Basic Setting

Sensor for Steering Angle (G85)

Prerequisites:

  • Start the vehicle.
  • Turn the steering wheel one turn to the right and one turn to the left.
  • Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
  • If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
  • Ensure that the steering wheel is not moved again.
  • Keep the engine running and do not switch off the ignition.
  • System voltage at least 12.0 V.

[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -4.5 and +4.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]

Lateral Acceleration Sensor (G200)

Prerequisites:

  • System voltage at least 12.0 V.

[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]

Brake Pressure Sensor 1 (G201)

Prerequisites:

  • System voltage at least 12.0 V.

[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 066
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -7.0 and +7.0 bar.
[Done, Go Back]
[Close Controller, Go Back - 06]

Longitudinal Acceleration Sensor (G251)

Prerequisites:

  • System voltage at least 12.0 V.

[Select]
[03 - Brake Electronics]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 069
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 006
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]

Special Procedures

System Function Test

See System Function Test