Difference between revisions of "VW Golf (1K) Steering Assist"

From Ross-Tech Wiki
m (VW Passat (3C) Steering Assist moved to VW Golf (1K) Steering Assist)
Line 2: Line 2:
  
 
== Adaptation ==
 
== Adaptation ==
 +
 +
== Basic Setting ==
 +
 +
=== Sensor for Steering Angle (G85) ===
 +
 +
'''<u>Prerequisites:</u>'''<br>
 +
* Start the vehicle.
 +
* Turn the steering wheel one turn to the right and one turn to the left.
 +
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
 +
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
 +
* Ensure that the steering wheel is not moved again.
 +
* Keep the engine running and do not switch off the ignition.
 +
* System voltage at least 12.0 V.<br><br>
 +
 +
'''[Select]'''<br>
 +
'''[44 - Steering Assist]'''<br>
 +
'''[Coding-II - 11]'''<br>
 +
Enter 40168, to enable the basic setting.<br>
 +
'''[Do it!]'''<br>
 +
'''[Basic Settings - 04]'''<br>
 +
Group 060<br>
 +
'''[Go!]'''<br>
 +
Activate the Basic Setting.<br>
 +
'''[ON/OFF/Next]'''<br>
 +
After a successful basic setting, field 1 should say "OK".<br>
 +
'''[Done, Go Back]'''<br>
 +
To make sure the basic setting was succesful, check the sensor again.<br>
 +
'''[Measuring Blocks - 08]'''<br>
 +
Group 007<br>
 +
'''[Go!]'''<br>
 +
Check field 1, the value has to be between -1.5 and +1.5 °.<br>
 +
'''[Done, Go Back]'''<br>
 +
'''[Close Controller, Go Back - 06]'''<br>
 +
 +
'''''Note:''' After successful basic setting, the [[VW_Golf_(1K)_Steering_Assist#Steering_Limit_Stop_Adaptation|Steering Limit Stop]] needs to be adapted too.''<br><br><br>
 +
  
 
== Special Procedures ==
 
== Special Procedures ==

Revision as of 17:01, 18 June 2006


Adaptation

Basic Setting

Sensor for Steering Angle (G85)

Prerequisites:

  • Start the vehicle.
  • Turn the steering wheel one turn to the right and one turn to the left.
  • Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
  • If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
  • Ensure that the steering wheel is not moved again.
  • Keep the engine running and do not switch off the ignition.
  • System voltage at least 12.0 V.

[Select]
[44 - Steering Assist]
[Coding-II - 11]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 1 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 007
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]

Note: After successful basic setting, the Steering Limit Stop needs to be adapted too.



Special Procedures

Steering Limit Stop Adaptation

  • Center steering wheel (±10°) and hold it centered for 5 seconds.
  • Turn steering wheel completely to the left and hold it there for a second.
  • Turn steering wheel completely to the right and hold it there for a second.
  • Center steering wheel (±10°).
  • Switch OFF engine and ignition.
  • Switch ON ignition.
  • Wait 5 seconds.
  • Steering Assist Warning Lamp should went OFF.