Difference between revisions of "VW Golf VII (5G/AU) ABS Brakes"

From Ross-Tech Wiki
Line 12: Line 12:
 
'''[03 - ABS Brakes]'''<br>
 
'''[03 - ABS Brakes]'''<br>
 
'''[Basic Settings - 04]'''<br>
 
'''[Basic Settings - 04]'''<br>
Select '''Start lining change mode'''''<br>
+
Select '''IDE03331-ENG114972 Start lining change mode'''''<br>
 
'''[Go!]''' to activate the Basic Setting.<br>
 
'''[Go!]''' to activate the Basic Setting.<br>
 
The brake calipers will then open, allowing the pads to be changed.<br>
 
The brake calipers will then open, allowing the pads to be changed.<br>
Line 29: Line 29:
 
'''[03 - ABS Brakes]'''<br>
 
'''[03 - ABS Brakes]'''<br>
 
'''[Basic Settings - 04]'''<br>
 
'''[Basic Settings - 04]'''<br>
Select '''End lining change mode'''''<br>
+
Select '''IDE03330-ENG114972 End lining change mode'''''<br>
 
'''[Go!]''' to activate the Basic Setting.<br>
 
'''[Go!]''' to activate the Basic Setting.<br>
 
The brake calipers will then close.<br>
 
The brake calipers will then close.<br>

Revision as of 10:00, 3 February 2017

Basic Setting

Caution!

  • Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.
  • Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.
  • It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults! There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door.

Open Rear Parking Brake

Prerequisites:

  • Connect a battery charger as per repair manual.
  • Cycle the Parking Brake ON, then OFF first.

[Select]
[03 - ABS Brakes]
[Basic Settings - 04]
Select IDE03331-ENG114972 Start lining change mode
[Go!] to activate the Basic Setting.
The brake calipers will then open, allowing the pads to be changed.
You should hear the rear caliper motors operating.
Wait 30 seconds after it says Not Running or the noises have stopped before clicking [Stop]
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Turn ignition off and leave battery charger connected.

The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool. Fault code 721152 - Brake pad replacement mode active will be stored, this is normal.

Close Rear Parking Brake

Prerequisites:

  • Connect a battery charger as per repair manual.

[Select]
[03 - ABS Brakes]
[Basic Settings - 04]
Select IDE03330-ENG114972 End lining change mode
[Go!] to activate the Basic Setting.
The brake calipers will then close.
Wait 30 seconds after it says Not Running or the noises have stopped before clicking [Stop]
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Turn ignition off

The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly in addition to Fault code 721152 - Brake pad replacement mode active. This should stop after cycling the Parking Brake ON, then OFF again using the switch in the vehicle while holding the brake pedal AFTER all rear brake components are reassembled.