Difference between revisions of "VW Jetta (16) Body Control Module"

From Ross-Tech Wiki
Line 32: Line 32:
 
=== Channel 001: Remote Control Matching ===
 
=== Channel 001: Remote Control Matching ===
  
* Start Matching new/additional Remote Controls by entering '''1''', then '''Test''' and '''Save''' the New Value.
+
* Start Matching new/additional Remote Controls by entering '''0''', then '''Test''' and '''Save''' the New Value.
 
* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
 
* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
  
'''Note''': If the new remote will not adapt to the module it may be necessary to clear all old remotes using the [[VW Jetta (16) Body Control Module#Channel 001: Remote Control Matching | Remote Control Clearing]] procedure.
+
'''Notes''':
 +
* If the new remote will not adapt to the module it may be necessary to clear all old remotes using the [[VW Jetta (16) Body Control Module#Channel 001: Remote Control Matching | Remote Control Clearing]] procedure.
 +
* If problems are encounter with this procedure and using "0" as the new value to match remotes, registered customers can [http://www.ross-tech.com/contact.html contact us directly]. Please send the complete Auto-Scan with the repair history details.
  
 
=== Channel 099: Factory Mode ===
 
=== Channel 099: Factory Mode ===

Revision as of 14:42, 6 September 2011


Information

  • Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with VCDS!
  • The Comfort System known from earlier Models has been integrated with the Central Electronics / Body Control Module (BCM) and is no longer available as a separate Address/Module. All related Diagnostics/Settings have to be performed via Central Electronics / Body Control Module (BCM).
  • The Door Electronics Modules known from earlier Models have been integrated with the Central Electronics / Body Control Module (BCM) as sub-systems and are no longer available as separate Address/Modules. All related Diagnostics/Settings have to be performed via Central Electronics / Body Control Module (BCM).
  • The Steering Wheel Electronics Module known from earlier Models is no longer installed. On vehicles with a Multi-Function Steering Wheel (MFSW) , the sub-system module is available for related Diagnostics/Settings.



Coding

  • Coding information is found using the Long Coding Helper while connected to the vehicle with VCDS.
  • When replacing a module it is critical to save the original coding and transfer it to the new module.



Adaptation

The complete list of Adaptation Channels are documented while connected to the vehicle with VCDS. The most common channels are noted below for common repair reference:

Channel 000: Remote Control Clearing

  • This Adaptation Channel is used to clear all matched Remote Controls.

Channel 001: Remote Control Matching

  • Start Matching new/additional Remote Controls by entering 0, then Test and Save the New Value.
  • Press and hold the Unlock button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.

Notes:

  • If the new remote will not adapt to the module it may be necessary to clear all old remotes using the Remote Control Clearing procedure.
  • If problems are encounter with this procedure and using "0" as the new value to match remotes, registered customers can contact us directly. Please send the complete Auto-Scan with the repair history details.

Channel 099: Factory Mode

Factory Mode is usually active when a newly delivered Control Module is being installed. To enable all Functions of the new Control Module Factory Mode has to be disabled. Once it has been disabled it cannot be enabled again.

  • When Factory Mode is enabled the doors will not lock and unlock properly and remotes may not program.



Replacement

  • Make sure all vehicle remotes are present.
  • Run and save a complete Auto-Scan and save it prior to module removal. See the Online Manual Auto-Scan.
  • Code the module with the Long Coding from the original module found in the Auto-Scan.
  • Disable Factory Mode
  • Remote Control Matching
  • Clear all fault codes and verify all comfort functions and lighting is working as per design.


Registered customers can contact us directly via email for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.