VW Passat (3B) Brake Electronics (Bosch 5.7)

From Ross-Tech Wiki
Revision as of 12:37, 9 March 2011 by Andy (talk | contribs)

Login

Note #1: After Login has been carried out you need to recode the control module.
Note #2: Special Login 07499 is used for 6-Cylinder Diesel Engine with 1LG Brakes and Multitronic.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.

  • 0?xxx: Chassis
    • 8 = VW Passat W8
    • 9 = VW Passat
  • 0x?xx: Brakes
    • 3 = (PR-1LT/1LF)
    • 4 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
    • 5 = (PR-1LB/1LE/1ZC)
    • 6 = (PR-1LZ/1ZJ)
  • 0xx?x: Engine
    • 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
    • 7 = (PR-T0B/T10/T6V/T0D/T0F)
    • 9 = (PR-T7F/T9H/T9J)
  • 0xxx?: Transmission
    • 5 = Manual (PR-G0C/G0K/G0G/G0L)
    • 7 = Automatic (PR-G0E/G0F/G0Q)

Coding

Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.

  • 0?xxx: Chassis
    • 4 = VW Passat
    • 5 = VW Passat W8
  • 0x?xx: Brakes
    • 1 = (PR-1LZ/1ZJ)
    • 2 = (PR-1LB/1LE/1ZC)
    • 3 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
    • 4 = (PR-1LT/1LF)
  • 0xx?x: Engine
    • 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
    • 7 = (PR-T0B/T10/T6V/T0D/T0F)
    • 9 = (PR-T7F/T9H/T9J)
  • 0xxx?: Transmission
    • 5 = Manual (PR-G0C/G0K/G0G/G0L)
    • 7 = Automatic (PR-G0E/G0F/G0Q)

Basic Setting

Steering Angle Sensor (G85) Calibration

Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]