Difference between revisions of "VW Passat (3C) Brake Electronics"
RtWiKiSyS0p (talk | contribs) |
RtWiKiSyS0p (talk | contribs) |
||
| Line 1: | Line 1: | ||
| + | __FORCETOC__ | ||
| + | |||
== Basic Setting == | == Basic Setting == | ||
| − | === | + | === Sensor for Steering Angle (G85) === |
| + | |||
| + | ---- | ||
| + | === Lateral Acceleration Sensor (G200) === | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| Line 19: | Line 24: | ||
'''[ON/OFF/Next]'''<br> | '''[ON/OFF/Next]'''<br> | ||
After a successful basic setting, field 3 should say "OK".<br> | After a successful basic setting, field 3 should say "OK".<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | To make sure the basic setting was succesful, check the sensor again.<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Group 004<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check field 2, the value has to be between -1.5 and +1.5 m/s².<br> | ||
| + | '''[Done, Go Back]'''<br><br> | ||
| + | |||
| + | ---- | ||
| + | === Brake Pressure Sensor 1 (G201) === | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[03 - Brake Electronics]'''<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Group 005<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check field 1, the value has to be between -8.0 and +8.0 bar.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Security Access - 16]'''<br> | ||
| + | Enter 40168, to enable the basic setting.<br> | ||
| + | '''[Do it!]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 066<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | After a successful basic setting, field 3 should say "OK".<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | To make sure the basic setting was succesful, check the sensor again.<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Group 005<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check field 1, the value has to be between -3.8 and +3.8 bar.<br> | ||
| + | '''[Done, Go Back]'''<br><br> | ||
| + | |||
| + | ---- | ||
| + | === Yaw Rate Sensor (G202) === | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[03 - Brake Electronics]'''<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Group 004<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check field 3, the value has to be between -1.5 and +1.5 m/s².<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Security Access - 16]'''<br> | ||
| + | Enter 40168, to enable the basic setting.<br> | ||
| + | '''[Do it!]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 068<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | After a successful basic setting, field 3 should say "OK".<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | To make sure the basic setting was succesful, check the sensor again.<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Group 004<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check field 3, the value has to be between -1.5 and +1.5 m/s².<br> | ||
'''[Done, Go Back]'''<br><br> | '''[Done, Go Back]'''<br><br> | ||
| − | + | ||
| + | ---- | ||
| + | === Longitudinal Acceleration Sensor (G251) === | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[03 - Brake Electronics]'''<br> | ||
'''[Measuring Blocks - 08]'''<br> | '''[Measuring Blocks - 08]'''<br> | ||
Group 004<br> | Group 004<br> | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
| − | Check field | + | Check field 4, the value has to be between -1.5 and +1.5 m/s².<br> |
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Security Access - 16]'''<br> | ||
| + | Enter 40168, to enable the basic setting.<br> | ||
| + | '''[Do it!]'''<br> | ||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 020<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Activate the Basic Setting.<br> | ||
| + | '''[ON/OFF/Next]'''<br> | ||
| + | The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| + | To make sure the basic setting was succesful, check the sensor again.<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Group 004<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check field 4, the value has to be between -2.5 and +2.5 m/s².<br> | ||
| + | '''[Done, Go Back]'''<br><br> | ||
Revision as of 11:30, 31 March 2006
Basic Setting
Sensor for Steering Angle (G85)
Lateral Acceleration Sensor (G200)
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
Brake Pressure Sensor 1 (G201)
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -8.0 and +8.0 bar.
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 066
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -3.8 and +3.8 bar.
[Done, Go Back]
Yaw Rate Sensor (G202)
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 3, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 3, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
Longitudinal Acceleration Sensor (G251)
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 4, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 4, the value has to be between -2.5 and +2.5 m/s².
[Done, Go Back]