Difference between revisions of "VW Passat (3C) Brake Electronics"

From Ross-Tech Wiki
Line 1: Line 1:
 
__FORCETOC__
 
__FORCETOC__
 +
 +
== Coding ==
 +
 +
''Currently, there is no coding information available for this module.''<br><br>
  
 
== Basic Setting ==
 
== Basic Setting ==
  
 
=== Sensor for Steering Angle (G85) ===
 
=== Sensor for Steering Angle (G85) ===
 +
 +
'''<u>Prerequisites</u>'''<br>
 +
* Start the vehicle.
 +
* Turn the steering wheel one turn to the right and one turn to the left.
 +
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
 +
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight
 +
* Ensure that the steering wheel is not moved again.
 +
* Keep the engine running and do not switch off the ignition.<br><br>
 +
 +
'''[Select]'''<br>
 +
'''[03 - Brake Electronics]'''<br>
 +
'''[Security Access - 16]'''<br>
 +
Enter 40168, to enable the basic setting.<br>
 +
'''[Do it!]'''<br>
 +
'''[Basic Settings - 04]'''<br>
 +
Group 060<br>
 +
'''[Go!]'''<br>
 +
Activate the Basic Setting.<br>
 +
'''[ON/OFF/Next]'''<br>
 +
After a successful basic setting, field 3 should say "OK".<br>
 +
'''[Done, Go Back]'''<br>
 +
To make sure the basic setting was succesful, check the sensor again.<br>
 +
'''[Measuring Blocks - 08]'''<br>
 +
Group 004<br>
 +
'''[Go!]'''<br>
 +
Check field 1, the value has to be between -1.5 and +1.5 °.<br>
 +
'''[Done, Go Back]'''<br>
 +
 +
'''''Note:''' After successful basic setting, the steering aid needs to be adapted too.''<br><br><br>
  
 
----
 
----
Line 30: Line 63:
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
 
Check field 2, the value has to be between -1.5 and +1.5 m/s².<br>
 
Check field 2, the value has to be between -1.5 and +1.5 m/s².<br>
'''[Done, Go Back]'''<br><br>
+
'''[Done, Go Back]'''<br><br><br>
  
 
----
 
----
Line 57: Line 90:
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
 
Check field 1, the value has to be between -3.8 and +3.8 bar.<br>
 
Check field 1, the value has to be between -3.8 and +3.8 bar.<br>
'''[Done, Go Back]'''<br><br>
+
'''[Done, Go Back]'''<br><br><br>
  
 
----
 
----
Line 84: Line 117:
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
 
Check field 3, the value has to be between -1.5 and +1.5 m/s².<br>
 
Check field 3, the value has to be between -1.5 and +1.5 m/s².<br>
'''[Done, Go Back]'''<br><br>
+
'''[Done, Go Back]'''<br><br><br>
  
 
----
 
----
Line 111: Line 144:
 
'''[Go!]'''<br>
 
'''[Go!]'''<br>
 
Check field 4, the value has to be between -2.5 and +2.5 m/s².<br>
 
Check field 4, the value has to be between -2.5 and +2.5 m/s².<br>
'''[Done, Go Back]'''<br><br>
+
'''[Done, Go Back]'''<br>

Revision as of 11:48, 31 March 2006


Coding

Currently, there is no coding information available for this module.

Basic Setting

Sensor for Steering Angle (G85)

Prerequisites

  • Start the vehicle.
  • Turn the steering wheel one turn to the right and one turn to the left.
  • Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
  • If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight
  • Ensure that the steering wheel is not moved again.
  • Keep the engine running and do not switch off the ignition.

[Select]
[03 - Brake Electronics]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]

Note: After successful basic setting, the steering aid needs to be adapted too.



Lateral Acceleration Sensor (G200)

[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]



Brake Pressure Sensor 1 (G201)

[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -8.0 and +8.0 bar.
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 066
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -3.8 and +3.8 bar.
[Done, Go Back]



Yaw Rate Sensor (G202)

[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 3, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 3 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 3, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]



Longitudinal Acceleration Sensor (G251)

[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 4, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The status of the Longitudinal Acceleration Sensor (G251) is now beeing displayed.
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 4, the value has to be between -2.5 and +2.5 m/s².
[Done, Go Back]