Difference between revisions of "VW Passat (3C) Immobilizer"

From Ross-Tech Wiki
(Created page with '== Replacement == ''This model uses Immobilizer Generation 4D which is integrated as part of the Comfort Control Module (J393). '''At the present time VCDS can only provide limi…')
 
 
(14 intermediate revisions by 4 users not shown)
Line 1: Line 1:
 
== Replacement ==
 
== Replacement ==
  
''This model uses Immobilizer Generation 4D which is integrated as part of the Comfort Control Module (J393). '''At the present time VCDS can only provide limited support for this Immobilizer Generation''' [http://www.ross-tech.com/vag-com/faq_4.html#skc <font color=red>Unless you ALREADY have the SKC information for your vehicle and components then you will NOT be able to do any of the Immobilizer functions.</font>]''
+
''This model uses Immobilizer Generation 4D which is integrated as part of the Comfort Control Module (J393). '''At the present time VCDS can only provide limited support for this Immobilizer Generation.''' [[Immobilizer#What Information is required for Immobilizer Procedures? |  <font color=red>Unless you ALREADY have the SKC information for your vehicle and components, you will NOT be able to perform any of the Immobilizer functions.</font>]]''
  
  
Line 16: Line 16:
  
  
'''Note''': ''The following sections are not available yet, if you happen to have the PIN/SKC and all other necessary Details for the Vehicle in question and need Instructions on how to proceed, [http://www.ross-tech.com/contact.html please contact us directly].
+
'''Note''': ''The following sections are not available yet, if you happen to have the PIN/SKC and all other necessary Details for the Vehicle in question and need Instructions on how to proceed, registered users can [mailto:Support@Ross-Tech.com email] us directly with a complete Auto-Scan.
  
 
=== Engine Control Unit (J623) Replacement ===
 
=== Engine Control Unit (J623) Replacement ===
 +
 +
* ''Currently not supported by VCDS.''
  
 
=== Comfort Control Module (J393) Replacement ===
 
=== Comfort Control Module (J393) Replacement ===
 +
 +
* ''Currently not supported by VCDS.''
  
 
=== Immobilizer/Remote Control Key Matching/Replacement ===
 
=== Immobilizer/Remote Control Key Matching/Replacement ===
 +
 +
* ''Supported by VCDS. Proper PIN/SKC and pre-programmed Keys (e.g. ordered via VW Dealer) are required.''
 +
* ''See [[Immobilizer IV Key Matching#VW Passat (3C) Immobilizer Key Matching|VW Passat (3C) Immobilizer Key Matching]] for Details.''
  
 
=== Electronic Steering Column Lock (J764) Replacement  ===
 
=== Electronic Steering Column Lock (J764) Replacement  ===
 +
 +
* ''NEW ''Electronic Steering Column Lock (J764) components can be matched but used components cannot be matched.''
 +
* ''If you have the PIN/SKC for the Vehicle, see this thread: https://forums.ross-tech.com/index.php?threads/784/#post-5511
 +
==== Special Notes ====
 +
* If the Ignition will not power on the Instrument cluster and CAN Gateway for communication after a new J764 is installed, hold the high beam stalk in the flash to pass position.  Turning the 4-way flashers (hazards) ON is another method that applies to Mk5/6 era VWs when CAN communication needs to be forced to match new Immobilizer components.
 +
* If the replacement J764 ESCL will not match make sure MVB group 081 contains the VIN to the vehicle and confirm group 123 contains all XX'es.  If a VIN is shown in group 123 the ESCL was already matched.  Used ESCLs canNOT be re-matched to another vehicle.

Latest revision as of 10:39, 21 October 2020

Replacement

This model uses Immobilizer Generation 4D which is integrated as part of the Comfort Control Module (J393). At the present time VCDS can only provide limited support for this Immobilizer Generation. Unless you ALREADY have the SKC information for your vehicle and components, you will NOT be able to perform any of the Immobilizer functions.


Immobilizer related work on this specific Model may be quite complicated, please make sure you have read and understood the additional Information which can be found in the Manufacturer Documentation:

  • Rest of World (RoW):
    • General Information on Immobilizer related Procedures for this Model, see TPI 2018893
    • Electronic Steering Column Lock (J764) Replacement, see TPI 2022458
  • North American Region (NAR):
    • Comfort System Central Control Module (J393) Replacement, see TSB 96-08-07 (2017731, superseded 96-08-03)
    • Immobilizer/Remote Control Key Replacement, see TSB 57-08-11 (2017087, superseded 57-08-01)
    • Electronic Steering Column Lock (J764) Replacement, see TSB 96-09-01 (2016689, superseded 96-08-08)


Note: The following sections are not available yet, if you happen to have the PIN/SKC and all other necessary Details for the Vehicle in question and need Instructions on how to proceed, registered users can email us directly with a complete Auto-Scan.

Engine Control Unit (J623) Replacement

  • Currently not supported by VCDS.

Comfort Control Module (J393) Replacement

  • Currently not supported by VCDS.

Immobilizer/Remote Control Key Matching/Replacement

Electronic Steering Column Lock (J764) Replacement

Special Notes

  • If the Ignition will not power on the Instrument cluster and CAN Gateway for communication after a new J764 is installed, hold the high beam stalk in the flash to pass position. Turning the 4-way flashers (hazards) ON is another method that applies to Mk5/6 era VWs when CAN communication needs to be forced to match new Immobilizer components.
  • If the replacement J764 ESCL will not match make sure MVB group 081 contains the VIN to the vehicle and confirm group 123 contains all XX'es. If a VIN is shown in group 123 the ESCL was already matched. Used ESCLs canNOT be re-matched to another vehicle.