VW Touareg (7P) Parking Brake

From Ross-Tech Wiki
Revision as of 15:18, 1 June 2017 by Dana (talk | contribs)

Important Note

Coding may zero after mechanical repairs to the rear brakes! We believe this the end result of a significant Air Gap discrepancy between specified and the actual adjustment of the parking brake shoes. Saving a complete Auto-Scan BEFORE any rear brake repairs is critical.

Coding

Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module. If this is not possible each coding inquiry has to be configured per vehicle based on the complete Auto-Scan and vehicle repair history. Registered Customers can email directly with each request.

The Security Access code for Coding Enabling will appear in a pop-up balloon when connected to this module with VCDS.

Replacement parts

Unlike conventional EPB systems found in most VW/Audi models, the large majority of the steps required during and after rear brake repairs on a 7P Touareg are mechanical rather than scan tool related.

We strongly advise the following BEFORE any repairs:

  • Run and Save a complete Auto-Scan before any mechanical repairs are made.
  • Add the following Advanced Measuring Value data to a log with the EPB released:
    • IDE04435-MAS01849 Air gap-Left
    • IDE04435-MAS01850 Air gap-Right
    • IDE05272-MAS01849 Air gap before calibration-Left
    • IDE05272-MAS01850 Air gap before calibration-Right

Rear Brake Pad and Rotor replacement

Due to the conventional nature of the hydraulic rear calipers and brake pads, diagnostic steps are not technically necessary to replace the pads or rotors but we strongly advise saving the Replacement parts data mentioned above.

  • After rear brake pad or rotor replacement the Air Gap needs to be checked, and adjusted if necessary, using the specifications found in the factory level repair manual. The before and after Advanced Measuring Value data can be used while following the repair manual steps.
  • If the 53-Parking Brake control module lost (zeroed) coding the original condition Auto-Scan can be used to re-code the module back to the factory condition.

Parking Brake Shoe replacement

The Air Gap will require significant adjustments after new parts are installed so all of the Replacement parts steps above are recommended prior to repairs.

  • The specifications and adjustment procedures found in the factory level repair manual need to be used. The General Air Gap specifications are 1.9 to 2.4mm with a max tolerance between left and right sides of 0 to 0.2mm.
  • After the parking brake shoes are adjusted using the threaded nut(s) make sure to cycle the EPB on/off using the switch in the vehicle so the Advanced Measuring Value data refreshes.
  • If the 53-Parking Brake control module lost (zeroed) coding the original condition Auto-Scan can be used to re-code the module back to the factory condition.
  • The Grind-In Output Test procedure (in the video linked below) should be completed after Parking Brake Shoe replacement.

Output Tests

We do not have a detailed plain text Output Tests Grind-In procedure to offer after mechanical repairs to this Electro-Mechanical Parking Brake (EPB) system at this time but this video demonstrates the procedure:

http://forums.ross-tech.com/showthread.php?3267-7P-T-Reg-EPB

Special Notes

  • Air Gap Spec is between 1.9mm to 2.4mm
  • Left and Right sides must be within 0.2mm of each other
  • Brake shoe adjuster, each click is a 0.15mm adjustment
    • Left side of vehicle:
      • Moving adjuster wheel towards front of vehicle, Air Gap gets smaller
      • Moving adjuster wheel towards rear of vehicle, Air Gap gets larger
    • Right side of vehicle:
      • Moving adjuster wheel towards front of vehicle, Air Gap gets larger
      • Moving adjuster wheel towards rear of vehicle, Air Gap gets smaller

Registered Customers encountering difficulty can email the full Auto-Scan in addition to a list of replaced parts and the Air Gap logs.

  • If the Air Gap Advanced Measuring Values do NOT change after the adjustments are complete; Make sure Basic Settings [*IDE04509*] Air gap calibration reports Finished Correctly, exit the controller, cycle the ignition, operate the EBP On/Off and re-check the Measuring Values.

TSD?ID=44700 | E?ID=139918 | ST?ID=75708