https://wiki.ross-tech.com/wiki/api.php?action=feedcontributions&feedformat=atom&user=Andy
Ross-Tech Wiki - User contributions [en]
2026-04-30T12:25:35Z
User contributions
MediaWiki 1.43.3
https://wiki.ross-tech.com/wiki/index.php?title=00834&diff=9788
00834
2025-10-01T16:51:45Z
<p>Andy: </p>
<hr />
<div>__FORCETOC__<br />
== 00834 - Signal for Activation of Heated Rear Window ==<br />
<br />
=== 00834 - Signal for Activation of Heated Rear Window: Open or Short to Ground ===<br />
<br />
==== Possible Symptoms ====<br />
<br />
* Rear Window Heater not working<br />
<br />
==== Possible Causes ====<br />
<br />
* Rear Window Heater faulty<br />
* Wiring/Connector(s) from/to Rear Window Heater faulty<br />
* Blown Fuse<br />
<br />
==== Possible Solutions ====<br />
<br />
* Check Rear Window Heater<br />
** See Measuring Value Blocks (MVB)<br />
* Check Rear Window Heater Feedback<br />
** See Window Defogger Switch (E230) LED<br />
** See Measuring Value Blocks (MVB)<br />
* Wiring/Connector(s) from/to Rear Window Heater faulty<br />
* Check Fuse for Rear Window Heater<br />
<br />
==== Special Notes ====<br />
<br />
* In an 8J Audi TT Roadster, check measuring values for the hall sensors per this forum thread: https://forums.ross-tech.com/index.php?threads/51398/.<br />
<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=SFD&diff=9754
SFD
2025-08-06T20:32:59Z
<p>Andy: /* Unlocking Schutz der Fahrzeugdiagnose (SFD) */</p>
<hr />
<div>= Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionality, which means it doesn't interfere with basic functions like reading Control Module Identification or Event and Diagnostic Trouble Codes (DTC's) or Measuring Values.<br />
<br />
Advanced functions like Coding, Adaptation, Basic Settings and/or Output Test may be limited and require a SFD unlock. SFD appeared first in MY 2020 and was at first limited to newly introduced Models and/or Control Modules. You will see Vehicles with individual Control Modules using classic Login/Security Access protections and other Control Modules in the same Vehicle using the newer SFD protection.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks to perform certain functions via an addition/suffix of "SFD" to the VCID line.<br />
<br />
Address 09: Cent. Elect. (J519) Labels: 1EA-937-BCM-V1.clb<br />
Part No SW: 1EE 937 089 D HW: 1EE 937 089<br />
Component: SAM_H H08 0530<br />
Serial number: 01102328300374 Dataset Number: V03935400RK 0001<br />
ASAM Dataset: EV_SAMVW31x 005001<br />
ROD: EV_SAMVW31x_005_VWE3.rod<br />
VCID: 43DB1062BB164BA2C69-8016 SFD<br />
<br />
<br />
= Schutz der Fahrzeugdiagnose 2 (SFD2) =<br />
<br />
SFD2 does NOT replace the aforementioned SFD. Instead it is meant as an extension for the original SFD functionality in order to secure Control Modules against unauthorized manipulation (by law). This is primarily aimed at driver assistance systems, autonomous driving, software updates and cyber security in general (i.e. UNECE R 155 and/or UNECE R 156).<br />
<br />
The vehicle manufacturer has to ensure that all modifications must be factory authorized, resulting in functions like Coding and Adaptation, as well as Updates etc. only being possible when digitally and cryptographically signed.<br />
<br />
This limitation does not apply to most service related functions like Service Reset, Particle Filter Regeneration, Brake Pad Replacements or other typical workshop jobs, as these can still be performed after a regular SFD unlock. SFD2 does however limit/prevent most retrofits and similar efforts to enable functions not available from factory.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD2 signed messages to perform certain functions via an addition/suffix of "SFD2" to the VCID line:<br />
<br />
Address 19: CAN Gateway (J533) Labels: 1EE-937-012.clb<br />
Part No SW: 1EE 937 012 D HW: 1EE 937 012<br />
Component: ICAS1 Host-SG 021 0411<br />
Serial number: SMERBG220923006 Dataset Number: V03935420NB 0001<br />
GVL: 2D00080006C8D0FC8062904248181050C400400000010000000200000000C057<br />
ASAM Dataset: EV_GatewICAS1MEBUNECE 001013<br />
ROD: EV_GatewICAS1MEBUNECE_VWE3.rod<br />
VCID: 353F7EBAE5C2E51278D-8060 SFD+SFD2<br />
<br />
= Diagnostic Firewall & Diagnostic Filter =<br />
<br />
Even before SFD and SFD2 unauthorized access and/or modifications were prevented by a diagnostic firewall, which required you to open the hood prior to having full access to control module functions. We recommend to open the hood on all MY 2015 and newer before you perform any diagnostic work to ensure the diagnostic firewall is deactivated.<br />
<br />
Newer models still have this diagnostic firewall but in addition may have diagnostic filter blocking diagnostic access to control modules entirely. VCDS uses a workaround to access these control modules but may be in Restricted (read-only) mode, preventing most advanced functions like Coding, Adaptation, Basic Settings and/or Output Test etc.<br />
<br />
An Auto-Scan with VCDS will show you if Restricted mode is active via an addition/suffix of "-R" to the VCID line for each control module:<br />
<br />
Address 06: Seat Mem. Pass (J521) Labels:* None<br />
Part No SW: 1N3 959 760 H HW: 1N3 959 760 H<br />
Component: MEM-BFS 011 0571<br />
Serial number: 23A3101KA04891<br />
Coding: 0118BA4000012A008803010101010000000000000000000000000000211000<br />
Shop #: WSC 00000 000 00000<br />
ASAM Dataset: EV_SCMPasseSideCONTIAU736 006013<br />
ROD: EV_SCMPasseSideCONTIAU736_VW38.rod<br />
VCID: 3E2D6196D0F4264AA97-806A-R<br />
<br />
An Auto-Scan with VCDS can show you in the VCID line combinations of "-R" and SFD and SFD at the same time:<br />
<br />
Address C003: SW Cluster Housekeeping (SWC3) Labels: V04-007-XXX-SWC3.clb<br />
Part No: V04 007 000 TB<br />
Component: ICAS1 SWCL_HK 0411 <br />
ASAM Dataset: EV_SWCLHouse1ICAS1UNECE 001007<br />
ROD: EV_SWCLHouse1ICAS1UNECE.rod<br />
VCID: 77A3B4B2BF4ED702AA1-8022-R SFD+SFD2<br />
<br />
<br />
= Unlocking Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
While we are working on automating the unlock process, VCDS already does support the unlock and re-lock procedure using offline unlock tokens.<br />
<br />
The following steps are recommended if you are working on SFD protected vehicles...<br />
<br />
# Determine which control modules you need to work on, for example:<br />
#* - Brake Electronics for Parking Brake related work<br />
#* - Information Electronics for Service Reset<br />
#<br />
# Determine if the diagnostic firewall was deactivated when opening the hood. This can be done by connecting to "Diagnostic Interface for Databus / Gateway" (#19) and viewing ''Diagnostic filter'' Advanced Measuring Values. Results that look like this confirm you do NOT need to unlock address 19 prior to making changes in other control modules:<br />
#:<br />
#* IDE13754-MAS16867 Diagnostic filter: status-Reason for deactivation hood open<br />
#* IDE13754-MAS16875 Diagnostic filter: status-Filter status Filter is not active<br />
#: <br />
#; In this case you can skip steps 3 and 4. The Diagnostic Firewall is already disabled. <br />
#: <br />
#: If the status is Filter active you will need to retrieve a Challenge/Token for "Diagnostic Interface for Databus / Gateway" (#19) and all additional SFD protected control modules you need to work on. Those results would look like this:<br />
#:<br />
#* IDE13754-IDE04447 Diagnosis filter: status-Function status Function active: SFD protected<br />
#* IDE13754-MAS16875 Diagnosis filter: status-Filter status Filter active<br />
#:<br />
#; In this case you must use steps 3 and 4. The Diagnostic Firewall active. <br />
#<br />
# SFD unlock the "Diagnostic Interface for Databus / Gateway" (#19) and verify the following Measuring Value shows a non-zero number of minutes:<br />
#:<br />
#* MAS18157-MAS18164 SFD activated status-Duration of vehicle diagnostic to be protected 89 minutes (this counts down to zero and then SFD is locked again automatically)<br />
#* <br />
#:<br />
# Disable the Diagnostic Filter in the "Diagnostic Interface for Databus / Gateway" (#19) (usually Adaptation channel IDE16611-Diagnosis filter: temporary deactivation adapted from active to not active) and check the following Measuring Value:<br />
#:<br />
#* IDE13754-MAS16866 Diagnosis filter: status-Odometer 20 km (this counts down from 20 km to zero and then the filter is locked again automatically)<br />
#:<br />
# SFD unlock (all) additional SFD protected control modules you plan to work on.<br />
<br />
= Frequently Asked Questions =<br />
<br />
# Can SFD be disabled?<br />
#: No.<br />
#<br />
# Can Ross-Tech provide offline SFD tokens?<br />
#: No, but they can be obtained for example [https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit from one of our distributors]<br />
#<br />
# Will VCDS have SFD unlocking built-in at some point?<br />
#: We hope to have that in the future and are working with VW to make this happen.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=SFD&diff=9753
SFD
2025-08-06T13:57:16Z
<p>Andy: /* Frequently Asked Questions */</p>
<hr />
<div>= Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionality, which means it doesn't interfere with basic functions like reading Control Module Identification or Event and Diagnostic Trouble Codes (DTC's) or Measuring Values.<br />
<br />
Advanced functions like Coding, Adaptation, Basic Settings and/or Output Test may be limited and require a SFD unlock. SFD appeared first in MY 2020 and was at first limited to newly introduced Models and/or Control Modules. You will see Vehicles with individual Control Modules using classic Login/Security Access protections and other Control Modules in the same Vehicle using the newer SFD protection.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks to perform certain functions via an addition/suffix of "SFD" to the VCID line.<br />
<br />
Address 09: Cent. Elect. (J519) Labels: 1EA-937-BCM-V1.clb<br />
Part No SW: 1EE 937 089 D HW: 1EE 937 089<br />
Component: SAM_H H08 0530<br />
Serial number: 01102328300374 Dataset Number: V03935400RK 0001<br />
ASAM Dataset: EV_SAMVW31x 005001<br />
ROD: EV_SAMVW31x_005_VWE3.rod<br />
VCID: 43DB1062BB164BA2C69-8016 SFD<br />
<br />
<br />
= Schutz der Fahrzeugdiagnose 2 (SFD2) =<br />
<br />
SFD2 does NOT replace the aforementioned SFD. Instead it is meant as an extension for the original SFD functionality in order to secure Control Modules against unauthorized manipulation (by law). This is primarily aimed at driver assistance systems, autonomous driving, software updates and cyber security in general (i.e. UNECE R 155 and/or UNECE R 156).<br />
<br />
The vehicle manufacturer has to ensure that all modifications must be factory authorized, resulting in functions like Coding and Adaptation, as well as Updates etc. only being possible when digitally and cryptographically signed.<br />
<br />
This limitation does not apply to most service related functions like Service Reset, Particle Filter Regeneration, Brake Pad Replacements or other typical workshop jobs, as these can still be performed after a regular SFD unlock. SFD2 does however limit/prevent most retrofits and similar efforts to enable functions not available from factory.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD2 signed messages to perform certain functions via an addition/suffix of "SFD2" to the VCID line:<br />
<br />
Address 19: CAN Gateway (J533) Labels: 1EE-937-012.clb<br />
Part No SW: 1EE 937 012 D HW: 1EE 937 012<br />
Component: ICAS1 Host-SG 021 0411<br />
Serial number: SMERBG220923006 Dataset Number: V03935420NB 0001<br />
GVL: 2D00080006C8D0FC8062904248181050C400400000010000000200000000C057<br />
ASAM Dataset: EV_GatewICAS1MEBUNECE 001013<br />
ROD: EV_GatewICAS1MEBUNECE_VWE3.rod<br />
VCID: 353F7EBAE5C2E51278D-8060 SFD+SFD2<br />
<br />
= Diagnostic Firewall & Diagnostic Filter =<br />
<br />
Even before SFD and SFD2 unauthorized access and/or modifications were prevented by a diagnostic firewall, which required you to open the hood prior to having full access to control module functions. We recommend to open the hood on all MY 2015 and newer before you perform any diagnostic work to ensure the diagnostic firewall is deactivated.<br />
<br />
Newer models still have this diagnostic firewall but in addition may have diagnostic filter blocking diagnostic access to control modules entirely. VCDS uses a workaround to access these control modules but may be in Restricted (read-only) mode, preventing most advanced functions like Coding, Adaptation, Basic Settings and/or Output Test etc.<br />
<br />
An Auto-Scan with VCDS will show you if Restricted mode is active via an addition/suffix of "-R" to the VCID line for each control module:<br />
<br />
Address 06: Seat Mem. Pass (J521) Labels:* None<br />
Part No SW: 1N3 959 760 H HW: 1N3 959 760 H<br />
Component: MEM-BFS 011 0571<br />
Serial number: 23A3101KA04891<br />
Coding: 0118BA4000012A008803010101010000000000000000000000000000211000<br />
Shop #: WSC 00000 000 00000<br />
ASAM Dataset: EV_SCMPasseSideCONTIAU736 006013<br />
ROD: EV_SCMPasseSideCONTIAU736_VW38.rod<br />
VCID: 3E2D6196D0F4264AA97-806A-R<br />
<br />
An Auto-Scan with VCDS can show you in the VCID line combinations of "-R" and SFD and SFD at the same time:<br />
<br />
Address C003: SW Cluster Housekeeping (SWC3) Labels: V04-007-XXX-SWC3.clb<br />
Part No: V04 007 000 TB<br />
Component: ICAS1 SWCL_HK 0411 <br />
ASAM Dataset: EV_SWCLHouse1ICAS1UNECE 001007<br />
ROD: EV_SWCLHouse1ICAS1UNECE.rod<br />
VCID: 77A3B4B2BF4ED702AA1-8022-R SFD+SFD2<br />
<br />
<br />
= Unlocking Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
While we are working on automating the unlock process, VCDS already does support the unlock and re-lock procedure using offline unlock tokens.<br />
<br />
The following steps are recommended if you are working on SFD protected vehicles...<br />
<br />
# Determine which control modules you need to work on, for example:<br />
#* - Brake Electronics for Parking Brake related work<br />
#* - Information Electronics for Service Reset<br />
#<br />
# Determine if the diagnostic firewall was deactivated when opening the hood. This can be done by connecting to "Diagnostic Interface for Databus / Gateway" (#19) and viewing ''Diagnostic filter'' Advanced Measuring Values. Results that look like this confirm you do NOT need to unlock address 19 prior to making changes in other control modules:<br />
#:<br />
#* IDE13754-MAS16867 Diagnostic filter: status-Reason for deactivation hood open<br />
#* IDE13754-MAS16875 Diagnostic filter: status-Filter status Filter is not active<br />
#: <br />
#; In this case you can skip steps 3 and 4. The Diagnostic Firewall is already disabled. <br />
#: <br />
#: If the status is Filter active you will need to retrieve a Challenge/Token for "Diagnostic Interface for Databus / Gateway" (#19) and all additional SFD protected control modules you need to work on. Those results would look like this:<br />
#:<br />
#* IDE13754-IDE04447 Diagnosis filter: status-Function status Function active: SFD protected<br />
#* IDE13754-MAS16875 Diagnosis filter: status-Filter status Filter active<br />
#:<br />
#; In this case you must use steps 3 and 4. The Diagnostic Firewall active. <br />
#<br />
# SFD unlock the "Diagnostic Interface for Databus / Gateway" (#19).<br />
#<br />
# Disable the Diagnostic Filter in the "Diagnostic Interface for Databus / Gateway" (#19) (usually Adaptation channel IDE16611-Diagnosis filter: temporary deactivation adapted from active to not active).<br />
#<br />
# SFD unlock (all) additional SFD protected control modules you plan to work on.<br />
<br />
<br />
<br />
= Frequently Asked Questions =<br />
<br />
# Can SFD be disabled?<br />
#: No.<br />
#<br />
# Can Ross-Tech provide offline SFD tokens?<br />
#: No, but they can be obtained for example [https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit from one of our distributors]<br />
#<br />
# Will VCDS have SFD unlocking built-in at some point?<br />
#: We hope to have that in the future and are working with VW to make this happen.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=SFD&diff=9752
SFD
2025-08-06T13:35:36Z
<p>Andy: </p>
<hr />
<div>= Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionality, which means it doesn't interfere with basic functions like reading Control Module Identification or Event and Diagnostic Trouble Codes (DTC's) or Measuring Values.<br />
<br />
Advanced functions like Coding, Adaptation, Basic Settings and/or Output Test may be limited and require a SFD unlock. SFD appeared first in MY 2020 and was at first limited to newly introduced Models and/or Control Modules. You will see Vehicles with individual Control Modules using classic Login/Security Access protections and other Control Modules in the same Vehicle using the newer SFD protection.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks to perform certain functions via an addition/suffix of "SFD" to the VCID line.<br />
<br />
Address 09: Cent. Elect. (J519) Labels: 1EA-937-BCM-V1.clb<br />
Part No SW: 1EE 937 089 D HW: 1EE 937 089<br />
Component: SAM_H H08 0530<br />
Serial number: 01102328300374 Dataset Number: V03935400RK 0001<br />
ASAM Dataset: EV_SAMVW31x 005001<br />
ROD: EV_SAMVW31x_005_VWE3.rod<br />
VCID: 43DB1062BB164BA2C69-8016 SFD<br />
<br />
<br />
= Schutz der Fahrzeugdiagnose 2 (SFD2) =<br />
<br />
SFD2 does NOT replace the aforementioned SFD. Instead it is meant as an extension for the original SFD functionality in order to secure Control Modules against unauthorized manipulation (by law). This is primarily aimed at driver assistance systems, autonomous driving, software updates and cyber security in general (i.e. UNECE R 155 and/or UNECE R 156).<br />
<br />
The vehicle manufacturer has to ensure that all modifications must be factory authorized, resulting in functions like Coding and Adaptation, as well as Updates etc. only being possible when digitally and cryptographically signed.<br />
<br />
This limitation does not apply to most service related functions like Service Reset, Particle Filter Regeneration, Brake Pad Replacements or other typical workshop jobs, as these can still be performed after a regular SFD unlock. SFD2 does however limit/prevent most retrofits and similar efforts to enable functions not available from factory.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD2 signed messages to perform certain functions via an addition/suffix of "SFD2" to the VCID line:<br />
<br />
Address 19: CAN Gateway (J533) Labels: 1EE-937-012.clb<br />
Part No SW: 1EE 937 012 D HW: 1EE 937 012<br />
Component: ICAS1 Host-SG 021 0411<br />
Serial number: SMERBG220923006 Dataset Number: V03935420NB 0001<br />
GVL: 2D00080006C8D0FC8062904248181050C400400000010000000200000000C057<br />
ASAM Dataset: EV_GatewICAS1MEBUNECE 001013<br />
ROD: EV_GatewICAS1MEBUNECE_VWE3.rod<br />
VCID: 353F7EBAE5C2E51278D-8060 SFD+SFD2<br />
<br />
= Diagnostic Firewall & Diagnostic Filter =<br />
<br />
Even before SFD and SFD2 unauthorized access and/or modifications were prevented by a diagnostic firewall, which required you to open the hood prior to having full access to control module functions. We recommend to open the hood on all MY 2015 and newer before you perform any diagnostic work to ensure the diagnostic firewall is deactivated.<br />
<br />
Newer models still have this diagnostic firewall but in addition may have diagnostic filter blocking diagnostic access to control modules entirely. VCDS uses a workaround to access these control modules but may be in Restricted (read-only) mode, preventing most advanced functions like Coding, Adaptation, Basic Settings and/or Output Test etc.<br />
<br />
An Auto-Scan with VCDS will show you if Restricted mode is active via an addition/suffix of "-R" to the VCID line for each control module:<br />
<br />
Address 06: Seat Mem. Pass (J521) Labels:* None<br />
Part No SW: 1N3 959 760 H HW: 1N3 959 760 H<br />
Component: MEM-BFS 011 0571<br />
Serial number: 23A3101KA04891<br />
Coding: 0118BA4000012A008803010101010000000000000000000000000000211000<br />
Shop #: WSC 00000 000 00000<br />
ASAM Dataset: EV_SCMPasseSideCONTIAU736 006013<br />
ROD: EV_SCMPasseSideCONTIAU736_VW38.rod<br />
VCID: 3E2D6196D0F4264AA97-806A-R<br />
<br />
An Auto-Scan with VCDS can show you in the VCID line combinations of "-R" and SFD and SFD at the same time:<br />
<br />
Address C003: SW Cluster Housekeeping (SWC3) Labels: V04-007-XXX-SWC3.clb<br />
Part No: V04 007 000 TB<br />
Component: ICAS1 SWCL_HK 0411 <br />
ASAM Dataset: EV_SWCLHouse1ICAS1UNECE 001007<br />
ROD: EV_SWCLHouse1ICAS1UNECE.rod<br />
VCID: 77A3B4B2BF4ED702AA1-8022-R SFD+SFD2<br />
<br />
<br />
= Unlocking Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
While we are working on automating the unlock process, VCDS already does support the unlock and re-lock procedure using offline unlock tokens.<br />
<br />
The following steps are recommended if you are working on SFD protected vehicles...<br />
<br />
# Determine which control modules you need to work on, for example:<br />
#* - Brake Electronics for Parking Brake related work<br />
#* - Information Electronics for Service Reset<br />
#<br />
# Determine if the diagnostic firewall was deactivated when opening the hood. This can be done by connecting to "Diagnostic Interface for Databus / Gateway" (#19) and viewing ''Diagnostic filter'' Advanced Measuring Values. Results that look like this confirm you do NOT need to unlock address 19 prior to making changes in other control modules:<br />
#:<br />
#* IDE13754-MAS16867 Diagnostic filter: status-Reason for deactivation hood open<br />
#* IDE13754-MAS16875 Diagnostic filter: status-Filter status Filter is not active<br />
#: <br />
#; In this case you can skip steps 3 and 4. The Diagnostic Firewall is already disabled. <br />
#: <br />
#: If the status is Filter active you will need to retrieve a Challenge/Token for "Diagnostic Interface for Databus / Gateway" (#19) and all additional SFD protected control modules you need to work on. Those results would look like this:<br />
#:<br />
#* IDE13754-IDE04447 Diagnosis filter: status-Function status Function active: SFD protected<br />
#* IDE13754-MAS16875 Diagnosis filter: status-Filter status Filter active<br />
#:<br />
#; In this case you must use steps 3 and 4. The Diagnostic Firewall active. <br />
#<br />
# SFD unlock the "Diagnostic Interface for Databus / Gateway" (#19).<br />
#<br />
# Disable the Diagnostic Filter in the "Diagnostic Interface for Databus / Gateway" (#19) (usually Adaptation channel IDE16611-Diagnosis filter: temporary deactivation adapted from active to not active).<br />
#<br />
# SFD unlock (all) additional SFD protected control modules you plan to work on.<br />
<br />
<br />
<br />
= Frequently Asked Questions =<br />
<br />
# Can SFD be disabled?<br />
#: No.<br />
#<br />
# Can Ross-Tech provide offline SFD tokens?<br />
#: No, but they can be obtained for example from one of our distributors:<br />
#; https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit<br />
#<br />
# Will VCDS have SFD unlocking built-in at some point?<br />
#: We hope to have that in the future and are working with VW to make this happen.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=SFD&diff=9751
SFD
2025-08-06T13:25:36Z
<p>Andy: </p>
<hr />
<div>= Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionality, which means it doesn't interfere with basic functions like reading Control Module Identification or Event and Diagnostic Trouble Codes (DTC's) or Measuring Values.<br />
<br />
Advanced functions like Coding, Adaptation, Basic Settings and/or Output Test may be limited and require a SFD unlock. SFD appeared first in MY 2020 and was at first limited to newly introduced Models and/or Control Modules. You will see Vehicles with individual Control Modules using classic Login/Security Access protections and other Control Modules in the same Vehicle using the newer SFD protection.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks to perform certain functions via an addition/suffix of "SFD" to the VCID line.<br />
<br />
Address 09: Cent. Elect. (J519) Labels: 1EA-937-BCM-V1.clb<br />
Part No SW: 1EE 937 089 D HW: 1EE 937 089<br />
Component: SAM_H H08 0530<br />
Serial number: 01102328300374 Dataset Number: V03935400RK 0001<br />
ASAM Dataset: EV_SAMVW31x 005001<br />
ROD: EV_SAMVW31x_005_VWE3.rod<br />
VCID: 43DB1062BB164BA2C69-8016 SFD<br />
<br />
<br />
= Schutz der Fahrzeugdiagnose 2 (SFD2) =<br />
<br />
SFD2 does NOT replace the aforementioned SFD. Instead it is meant as an extension for the original SFD functionality in order to secure Control Modules against unauthorized manipulation (by law). This is primarily aimed at driver assistance systems, autonomous driving, software updates and cyber security in general (i.e. UNECE R 155 and/or UNECE R 156).<br />
<br />
The vehicle manufacturer has to ensure that all modifications must be factory authorized, resulting in functions like Coding and Adaptation, as well as Updates etc. only being possible when digitally and cryptographically signed.<br />
<br />
This limitation does not apply to most service related functions like Service Reset, Particle Filter Regeneration, Brake Pad Replacements or other typical workshop jobs, as these can still be performed after a regular SFD unlock. SFD2 does however limit/prevent most retrofits and similar efforts to enable functions not available from factory.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD2 signed messages to perform certain functions via an addition/suffix of "SFD2" to the VCID line:<br />
<br />
Address 19: CAN Gateway (J533) Labels: 1EE-937-012.clb<br />
Part No SW: 1EE 937 012 D HW: 1EE 937 012<br />
Component: ICAS1 Host-SG 021 0411<br />
Serial number: SMERBG220923006 Dataset Number: V03935420NB 0001<br />
GVL: 2D00080006C8D0FC8062904248181050C400400000010000000200000000C057<br />
ASAM Dataset: EV_GatewICAS1MEBUNECE 001013<br />
ROD: EV_GatewICAS1MEBUNECE_VWE3.rod<br />
VCID: 353F7EBAE5C2E51278D-8060 SFD+SFD2<br />
<br />
= Diagnostic Firewall & Diagnostic Filter =<br />
<br />
Even before SFD and SFD2 unauthorized access and/or modifications were prevented by a diagnostic firewall, which required you to open the hood prior to having full access to control module functions. We recommend to open the hood on all MY 2015 and newer before you perform any diagnostic work to ensure the diagnostic firewall is deactivated.<br />
<br />
Newer models still have this diagnostic firewall but in addition may have diagnostic filter blocking diagnostic access to control modules entirely. VCDS uses a workaround to access these control modules but may be in Restricted (read-only) mode, preventing most advanced functions like Coding, Adaptation, Basic Settings and/or Output Test etc.<br />
<br />
An Auto-Scan with VCDS will show you if Restricted mode is active via an addition/suffix of "-R" to the VCID line for each control module:<br />
<br />
Address 06: Seat Mem. Pass (J521) Labels:* None<br />
Part No SW: 1N3 959 760 H HW: 1N3 959 760 H<br />
Component: MEM-BFS 011 0571<br />
Serial number: 23A3101KA04891<br />
Coding: 0118BA4000012A008803010101010000000000000000000000000000211000<br />
Shop #: WSC 00000 000 00000<br />
ASAM Dataset: EV_SCMPasseSideCONTIAU736 006013<br />
ROD: EV_SCMPasseSideCONTIAU736_VW38.rod<br />
VCID: 3E2D6196D0F4264AA97-806A-R<br />
<br />
An Auto-Scan with VCDS can show you in the VCID line combinations of "-R" and SFD and SFD at the same time:<br />
<br />
Address C003: SW Cluster Housekeeping (SWC3) Labels: V04-007-XXX-SWC3.clb<br />
Part No: V04 007 000 TB<br />
Component: ICAS1 SWCL_HK 0411 <br />
ASAM Dataset: EV_SWCLHouse1ICAS1UNECE 001007<br />
ROD: EV_SWCLHouse1ICAS1UNECE.rod<br />
VCID: 77A3B4B2BF4ED702AA1-8022-R SFD+SFD2<br />
<br />
<br />
= Unlocking Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
While we are working on automating the unlock process, VCDS already does support the unlock and re-lock procedure using offline unlock tokens.<br />
<br />
The following steps are recommended if you are working on SFD protected vehicles...<br />
<br />
# Determine which control modules you need to work on, for example:<br />
#* - Brake Electronics for Parking Brake related work<br />
#* - Information Electronics for Service Reset<br />
#<br />
# Determine if the diagnostic firewall was deactivated when opening the hood. This can be done by connecting to "Diagnostic Interface for Databus / Gateway" (#19) and viewing ''Diagnostic filter'' Advanced Measuring Values.<br />
#*<br />
#* Results that look like this confirm you do NOT need to unlock address 19 prior to making changes in other control modules:<br />
#*<br />
: IDE13754-MAS16867 Diagnostic filter: status-Reason for deactivation hood open<br />
: IDE13754-MAS16875 Diagnostic filter: status-Filter status Filter is not active<br />
# <br />
#* '''In this case you can skip steps 3 and 4. The Diagnostic Firewall is already disabled.'''<br />
# <br />
# * If the status is Filter active you will need to retrieve a Challenge/Token for "Diagnostic Interface for Databus / Gateway" (#19) and all additional SFD protected control modules you need to work on. Those results would look like this:<br />
<br />
IDE13754-IDE04447 Diagnosis filter: status-Function status Function active: SFD protected<br />
IDE13754-MAS16875 Diagnosis filter: status-Filter status Filter active<br />
<br />
'''In this case you must use steps 3 and 4. The Diagnostic Firewall active.'''<br />
<br />
<br />
3. SFD unlock the "Diagnostic Interface for Databus / Gateway" (#19).<br />
<br />
4. Disable the Diagnostic Filter in the "Diagnostic Interface for Databus / Gateway" (#19) (usually Adaptation channel IDE16611-Diagnosis filter: temporary deactivation adapted from active to not active).<br />
<br />
5. SFD unlock (all) additional SFD protected control modules you plan to work on.<br />
<br />
<br />
<br />
= Frequently Asked Questions =<br />
<br />
# Can SFD be disabled?<br />
#* No.<br />
#<br />
# Can Ross-Tech provide offline SFD tokens?<br />
#* No, but they can be obtained for example from one of our distributors:<br />
#* https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit<br />
<br />
3) Will VCDS have SFD unlocking built-in at some point?<br />
<br />
We hope to have that in the future and are working with VW to make this happen.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Main_Page&diff=9748
Main Page
2025-08-05T20:45:35Z
<p>Andy: </p>
<hr />
<div><center><u>'''Welcome to the Ross-Tech WIKI.'''</u><br><br><br />
<br />
''At the present time, this Wiki is experimental, and editable only by a small group.''<br><br />
''All content can be browsed '''WITHOUT''' an account. An account is only needed for those''<br><br />
''who wish to contribute on a regular basis! If you have a single contribution, please submit''<br><br />
''plain text to Support@Ross-Tech.com. If you submit contributions regularly using this method,''<br><br />
''we will likely contact you and offer to set up an account for you.''<br><br><br />
<br />
''Any links that are in RED are to pages that do not yet exist.''<br><br />
''There is thus no point in emailing Ross-Tech if you are trying to view that content.''<br></center><br />
<br />
<br />
<!-- TOC --><br />
<table align="center" width="80%" style="background:#eaeaea;"><br />
<caption style="color: #7d7d7d;text-align: center; font-size: 18px; font-weight: bold; padding-bottom: 6px;">Table of Contents</caption><br />
<tr> <br />
<td style="font-size: 14px;" width="25%" height="40px" align="center">'''[[Diagnostic Procedures]]'''</td> <br />
<td style="font-size: 14px;" width="25%" height="40px" align="center">'''General'''</td><br />
<td style="font-size: 14px;" width="25%" height="40px" align="center">'''Documentation'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7; border: none;font-size: 14px;" height="30px">[[Diagnostic Procedures#Audi|'''Audi''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7; border: none;font-size: 14px;" height="30px">[[:Category:Fault Codes|'''Fault Codes''']]</td><br />
<td width="25%" align="center" style="background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/main_screen.html '''VCDS Manual''']</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures#Seat|'''Seat''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Common Procedures]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Control Module Maps]]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures#Skoda|'''Skoda''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Retrofitting]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Common Acronyms]]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures#Volkswagen|'''Volkswagen''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Immobilizer]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Official Factory Repair Information]]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic_Procedures#Miscellaneous|'''Engines & Transmissions''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[SFD]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[http://meta.wikipedia.org/wiki/MediaWiki_User%27s_Guide WIKI User's Guide]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Functions|Function Chart]] '''</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px"> [https://forums.ross-tech.com ''' Ross-Tech Forum ''']</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Videos]]'''</td><br />
</tr><br />
</table><br />
<br />
<br><br />
<div style="text-align: center;"><br />
== How to use the Ross-Tech Wiki ==<br />
<br />
[[File:Wiki_video_thumb.png|400px|link=http://www.youtube.com/watch?v=8BIyIGV1_mw]]<br />
<br />
http://www.youtube.com/watch?v=8BIyIGV1_mw<br />
<br />
"''Give a man a fish and you'll have fed him for a day. Teach a man to fish and you can sell him fishing equipment''"<br />
</div></div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=SFD&diff=9747
SFD
2025-08-05T20:39:44Z
<p>Andy: </p>
<hr />
<div>= Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionality, which means it doesn't interfere with basic functions like reading Control Module Identification or Event and Diagnostic Trouble Codes (DTC's) or Measuring Values.<br />
<br />
Advanced functions like Coding, Adaptation, Basic Settings and/or Output Test may be limited and require a SFD unlock. SFD appeared first in MY 2020 and was at first limited to newly introduced Models and/or Control Modules. You will see Vehicles with individual Control Modules using classic Login/Security Access protections and other Control Modules in the same Vehicle using the newer SFD protection.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks to perform certain functions via an addition/suffix of "SFD" to the VCID line.<br />
<br />
Address 09: Cent. Elect. (J519) Labels: 1EA-937-BCM-V1.clb<br />
Part No SW: 1EE 937 089 D HW: 1EE 937 089<br />
Component: SAM_H H08 0530<br />
Serial number: 01102328300374 Dataset Number: V03935400RK 0001<br />
ASAM Dataset: EV_SAMVW31x 005001<br />
ROD: EV_SAMVW31x_005_VWE3.rod<br />
VCID: 43DB1062BB164BA2C69-8016 SFD<br />
<br />
<br />
= Schutz der Fahrzeugdiagnose 2 (SFD2) =<br />
<br />
SFD2 does NOT replace the aforementioned SFD. Instead it is meant as an extension for the original SFD functionality in order to secure Control Modules against unauthorized manipulation (by law). This is primarily aimed at driver assistance systems, autonomous driving, software updates and cyber security in general (i.e. UNECE R 155 and/or UNECE R 156).<br />
<br />
The vehicle manufacturer has to ensure that all modifications must be factory authorized, resulting in functions like Coding and Adaptation, as well as Updates etc. only being possible when digitally and cryptographically signed.<br />
<br />
This limitation does not apply to most service related functions like Service Reset, Particle Filter Regeneration, Brake Pad Replacements or other typical workshop jobs, as these can still be performed after a regular SFD unlock. SFD2 does however limit/prevent most retrofits and similar efforts to enable functions not available from factory.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD2 signed messages to perform certain functions via an addition/suffix of "SFD2" to the VCID line.<br />
<br />
Address 19: CAN Gateway (J533) Labels: 1EE-937-012.clb<br />
Part No SW: 1EE 937 012 D HW: 1EE 937 012<br />
Component: ICAS1 Host-SG 021 0411<br />
Serial number: SMERBG220923006 Dataset Number: V03935420NB 0001<br />
GVL: 2D00080006C8D0FC8062904248181050C400400000010000000200000000C057<br />
ASAM Dataset: EV_GatewICAS1MEBUNECE 001013<br />
ROD: EV_GatewICAS1MEBUNECE_VWE3.rod<br />
VCID: 353F7EBAE5C2E51278D-8060 SFD+SFD2<br />
<br />
= Diagnostic Firewall & Diagnostic Filter =<br />
<br />
Even before SFD and SFD2 unauthorized access and/or modifications were prevented by a diagnostic firewall, which required you to open the hood prior to having full access to control module functions. We recommend to open the hood on all MY 2015 and newer before you perform any diagnostic work to ensure the diagnostic firewall is deactivated.<br />
<br />
Newer models still have this diagnostic firewall but in addition may have diagnostic filter blocking diagnostic access to control modules entirely. VCDS uses a workaround to access these control modules but may be in Restricted (read-only) mode, preventing most advanced functions like Coding, Adaptation, Basic Settings and/or Output Test etc.<br />
<br />
An Auto-Scan with VCDS will show you if Restricted mode is active via an addition/suffix of "-R" to the VCID line for each control module.<br />
<br />
Address 06: Seat Mem. Pass (J521) Labels:* None<br />
Part No SW: 1N3 959 760 H HW: 1N3 959 760 H<br />
Component: MEM-BFS 011 0571<br />
Serial number: 23A3101KA04891<br />
Coding: 0118BA4000012A008803010101010000000000000000000000000000211000<br />
Shop #: WSC 00000 000 00000<br />
ASAM Dataset: EV_SCMPasseSideCONTIAU736 006013<br />
ROD: EV_SCMPasseSideCONTIAU736_VW38.rod<br />
VCID: 3E2D6196D0F4264AA97-806A-R<br />
<br />
An Auto-Scan with VCDS can show you in the VCID line combinations or "-R" and SFD and SFD at the same time:<br />
<br />
Address C003: SW Cluster Housekeeping (SWC3) Labels: V04-007-XXX-SWC3.clb<br />
Part No: V04 007 000 TB<br />
Component: ICAS1 SWCL_HK 0411 <br />
ASAM Dataset: EV_SWCLHouse1ICAS1UNECE 001007<br />
ROD: EV_SWCLHouse1ICAS1UNECE.rod<br />
VCID: 77A3B4B2BF4ED702AA1-8022-R SFD+SFD2<br />
<br />
<br />
= Unlocking Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
While we are working on automating the unlock process, VCDS already does support the unlock and re-lock procedure using offline unlock tokens.<br />
<br />
The following steps are recommended if you are working on SFD protected vehicles...<br />
<br />
1. Determine which control modules you need to work on, for example:<br />
- Brake Electronics for Parking Brake related work<br />
- Information Electronics for Service Reset<br />
<br />
2. Retrieve Challenge/Token for "Diagnostic Interface for Databus / Gateway" (#19) and all additional control modules you need to work on.<br />
<br />
3. Unlock the "Diagnostic Interface for Databus / Gateway" (#19).<br />
<br />
4. Unlock the Diagnostic Filter in the "Diagnostic Interface for Databus / Gateway" (#19) (usually Adaptation channel IDE16611-Diagnosis filter: temporary deactivation adapted from active to not active).<br />
<br />
5. Unlock (all) additional control modules you plan to work on.<br />
<br />
<br />
= Frequently Asked Questions =<br />
<br />
1) Can SFD be disabled?<br />
<br />
No.<br />
<br />
2) Can Ross-Tech provide offline SFD tokens?<br />
<br />
No, but they can be obtained for example from one of our distributors:<br />
<br />
https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit<br />
<br />
3) Will VCDS have SFD unlocking built-in at some point?<br />
<br />
We hope to have that in the future and are working with VW to make this happen.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=SFD&diff=9746
SFD
2025-08-05T20:20:33Z
<p>Andy: Created page with "= Schutz der Fahrzeugdiagnose (SFD) = Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionali..."</p>
<hr />
<div>= Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
Schutz der Fahrzeugdiagnose (SFD) aka. Protection of Vehicle Diagnostics (PVD) replaces the existing Login & Security Access functionality, which means it doesn't interfere with basic functions like reading Control Module Identification or Event and Diagnostic Trouble Codes (DTC's) or Measuring Values.<br />
<br />
Advanced functions like Coding, Adaptation, Basic Settings and/or Output Test may be limited and require a SFD unlock. SFD appeared first in MY 2020 and was at first limited to newly introduced Models and/or Control Modules. You will see Vehicles with individual Control Modules using classic Login/Security Access protections and other Control Modules in the same Vehicle using the newer SFD protection.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks via an addition/suffix of "SFD" to the VCID line.<br />
<br />
Address 09: Cent. Elect. (J519) Labels: 1EA-937-BCM-V1.clb<br />
Part No SW: 1EE 937 089 D HW: 1EE 937 089<br />
Component: SAM_H H08 0530<br />
Serial number: 01102328300374 Dataset Number: V03935400RK 0001<br />
ASAM Dataset: EV_SAMVW31x 005001<br />
ROD: EV_SAMVW31x_005_VWE3.rod<br />
VCID: 43DB1062BB164BA2C69-8016 SFD<br />
<br />
<br />
= Schutz der Fahrzeugdiagnose 2 (SFD2) =<br />
<br />
SFD2 does NOT replace the aforementioned SFD. Instead it is meant as an extension for the original SFD functionality in order to secure Control Modules against unauthorized manipulation (by law). This is primarily aimed at driver assistance systems, autonomous driving, software updates and cyber security in general (i.e. UNECE R 155 and/or UNECE R 156).<br />
<br />
The vehicle manufacturer has to ensure that all modifications must be factory authorized, resulting in functions like Coding and Adaptation, as well as Updates etc. only being possible when digitally and cryptographically signed.<br />
<br />
This limitation does not apply to most service related functions like Service Reset, Particle Filter Regeneration, Brake Pad Replacements or other typical workshop jobs, as these can still be performed after a regular SFD unlock. SFD2 does however limit/prevent most retrofits and similar efforts to enable functions not available from factory.<br />
<br />
An Auto-Scan with VCDS will show you if a specific control module requires SFD unlocks via an addition/suffix of "SFD2" to the VCID line.<br />
<br />
Address 19: CAN Gateway (J533) Labels: 1EE-937-012.clb<br />
Part No SW: 1EE 937 012 D HW: 1EE 937 012<br />
Component: ICAS1 Host-SG 021 0411<br />
Serial number: SMERBG220923006 Dataset Number: V03935420NB 0001<br />
GVL: 2D00080006C8D0FC8062904248181050C400400000010000000200000000C057<br />
ASAM Dataset: EV_GatewICAS1MEBUNECE 001013<br />
ROD: EV_GatewICAS1MEBUNECE_VWE3.rod<br />
VCID: 353F7EBAE5C2E51278D-8060 SFD+SFD2<br />
<br />
= Diagnostic Firewall & Diagnostic Filter =<br />
<br />
Even before SFD and SFD2 unauthorized access and/or modifications were prevented by a diagnostic firewall, which required you to open the hood prior to having full access to control module functions. We recommend to open the hood on all MY 2015 and newer before you perform any diagnostic work to ensure the diagnostic firewall is deactivated.<br />
<br />
Newer models still have this diagnostic firewall but in addition may have diagnostic filter blocking diagnostic access to control modules entirely. VCDS uses a workaround to access these control modules but may be in restricted mode, preventing most advanced functions like Coding, Adaptation, Basic Settings and/or Output Test etc.<br />
<br />
An Auto-Scan with VCDS will show you if restricted mode is active via an addition/suffix of "-R" to the VCID line for each control module.<br />
<br />
Address 06: Seat Mem. Pass (J521) Labels:* None<br />
Part No SW: 1N3 959 760 H HW: 1N3 959 760 H<br />
Component: MEM-BFS 011 0571<br />
Serial number: 23A3101KA04891<br />
Coding: 0118BA4000012A008803010101010000000000000000000000000000211000<br />
Shop #: WSC 00000 000 00000<br />
ASAM Dataset: EV_SCMPasseSideCONTIAU736 006013<br />
ROD: EV_SCMPasseSideCONTIAU736_VW38.rod<br />
VCID: 3E2D6196D0F4264AA97-806A-R<br />
<br />
<br />
= Unlocking Schutz der Fahrzeugdiagnose (SFD) =<br />
<br />
While we are working on automating the unlock process, VCDS already does support the unlock and re-lock procedure using offline unlock tokens.<br />
<br />
The following steps are recommended if you are working on SFD protected vehicles...<br />
<br />
1. Determine which control modules you need to work on, for example:<br />
- Brake Electronics for Parking Brake related work<br />
- Information Electronics for Service Reset<br />
<br />
2. Retrieve Challenge/Token for "Diagnostic Interface for Databus / Gateway" (#19) and all additional control modules you need to work on.<br />
<br />
3. Unlock the "Diagnostic Interface for Databus / Gateway" (#19).<br />
<br />
4. Unlock the Diagnostic Filter in the "Diagnostic Interface for Databus / Gateway" (#19) (usually Adaptation channel IDE16611-Diagnosis filter: temporary deactivation adapted from active to not active).<br />
<br />
5. Unlock (all) additional control modules you plan to work on.<br />
<br />
<br />
= Frequently Asked Questions =<br />
<br />
1) Can SFD be disabled?<br />
<br />
No.<br />
<br />
2) Can Ross-Tech provide offline SFD tokens?<br />
<br />
No, but they can be obtained for example from one of our distributors:<br />
<br />
https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit<br />
<br />
3) Will VCDS have SFD unlocking built-in at some point?<br />
<br />
We hope to have that in the future and are working with VW to make this happen.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=User:Andy&diff=9727
User:Andy
2025-07-17T12:29:46Z
<p>Andy: </p>
<hr />
<div><font color=red>This is my test page please leave it alone</font> ;-)<br />
<br />
<br />
{| role="Presentation" class="wikitable" style="background:lightgray; text-align:center; width:99%" "border="0"<br />
|-<br />
! !! No SFD !! SFD in 17 !! SFD in 5F !! SFD2 / Filter<br />
|-<br />
! Service Reset<br />
| style="background:limegreen" | Just Perform SRI || style="background:orange" | Unlock SFD in 17 || style="background:orange" | Unlock SDF in 5F|| style="background:red" | Unlock SFD in 19<br />
|-<br />
! Unlock SFD?<br />
| style="background:limegreen" | No || style="background:orange" | Yes || style="background:orange" | Yes || style="background:red" | Yes in both 5F and 17<br />
|-<br />
! Change Adaptation Channel<br />
| style="background:limegreen" | Yes || style="background:orange" | Yes after unlocking 17 || style="background:orange" | Yes after unlocking 5F || style="background:red" |Yes after unlocking/unfiltering 19, then unlocking 19/5F<br />
|-<br />
|}<br />
<br />
NI0<br />
- Ohne UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI1<br />
- Mit UNECE Cyber-Security Schutz<br />
- Mit UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI7<br />
- Mit UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI8<br />
- Ohne UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Mit SFD2 Steuergerät<br />
<br />
NI9 <br />
- Mit UNECE Cyber-Security Schutz (für Länder ohne UNECE Anforderungen)<br />
- Mit UNECE Software-Update Schutz (für Länder ohne UNECE Anforderungen)<br />
- Ohne SFD2 Steuergerät<br />
<br />
<br />
Resetting Service Reminders (SRI) is one function that is affected by the changes that VW/Audi have made relating to SFD/SFD2 and UNECE R155/R156. These measures can prevent changes or even block access to the vehicle. VCDS should be able to read all control modules and read all Adaptation channels even in the latest vehicles, but making changes (such as resetting service reminders) can become complicated.<br />
<br />
Let's start with the older vehicles, typically pre-2020, which lack SFD. <br />
<br />
Case 1 - No SFD: Just reset the service reminder using VCDS: https://www.ross-tech.com/vcds/tour/sri-reset.php<br />
<br />
Case 2 - SFD: When SFD was firsts introduced for example in the MEB (VW ID.4, etc.) or MQBevo (Golf 8, etc.) some modules have SFD such as 5F in the MEB and 17 in the MQBevo. This means to save Adaptation values to reset the service reminder, you would first need to unlock SFD in the module you are trying to change. This can be done with an offline token, like one from one of our German distributors: https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit<br />
After that is unlocked (it stays unlocked for 90 minutes) then SRI Reset can proceed as normal. This process will need to be done again with a new SFD token at the next service reminder.<br />
<br />
Case 3 - SFD with Diagnostic Filter on the Gateway. This development came along with for example the 2024+ ID.4 which not only has SFD on some modules, but also has an SFD equipped CAN Gateway that contains an Adaptation channel for a diagnostic filter. By default, this filter prevents viewing other modules in the cars, let alone making changes in them. VCDS contains a workaround (R-Mode) that allows reading all of the modules and their info without first unlocking SFD but any changes will be blocked. In order to make changes in any modules in one of these vehicles, the first step would be to unlock SFD in 19-CAN Gateway (for example using an offline token like one purchased through the link above in Case 2). After 19 is unlocked, an Adaptation channel like this in 19-CAN Gateway can be changed: DE16611-Diagnosis filter: temporary deactivation adapted from active to not active. That turns off the filter which remains off for 20km. Next, the other modules in the car should be accessible without using R-Mode but any SFD modules will still prevent changes from being made. For example to reset the service reminder in the 2024 ID.4 the next step would be to go into address 5F and unlock SFD (using another token) then proceed to save the Adaptation channel(s) to reset SRI. Note that since R-Mode allow you to read data even in modules that the Gateway is filtering, it should be possible to read the SFD challenge from both 19-CAN Gateway and 5F while everything is still locked, to then order BOTH offline SFD tokens at the same time.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=User:Andy&diff=9726
User:Andy
2025-07-17T12:14:39Z
<p>Andy: </p>
<hr />
<div><font color=red>This is my test page please leave it alone</font> ;-)<br />
<br />
<br />
{| role="Presentation" class="wikitable" style="background:lightgray; text-align:center; width:99%" "border="0"<br />
|-<br />
! !! No SFD !! SFD in 17 !! SFD in 5F !! SFD2 / Filter<br />
|-<br />
! Service Reset<br />
| style="background:limegreen" | Just Perform SRI || style="background:orange" | Unlock SFD in 17 || style="background:orange" | Unlock SDF in 5F|| style="background:red" | Unlock SFD in 19<br />
|-<br />
! Unlock SFD?<br />
| style="background:limegreen" | No || style="background:orange" | Yes || style="background:red" | Yes || style="background:red" | Not Supported<br />
|-<br />
! Change Adaptation Channel<br />
| style="background:limegreen" | No || style="background:orange" | Original/Car PIN needed || style="background:orange" | Original/Car PIN needed || style="background:red" |N/A<br />
|-<br />
|}<br />
<br />
NI0<br />
- Ohne UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI1<br />
- Mit UNECE Cyber-Security Schutz<br />
- Mit UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI7<br />
- Mit UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI8<br />
- Ohne UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Mit SFD2 Steuergerät<br />
<br />
NI9 <br />
- Mit UNECE Cyber-Security Schutz (für Länder ohne UNECE Anforderungen)<br />
- Mit UNECE Software-Update Schutz (für Länder ohne UNECE Anforderungen)<br />
- Ohne SFD2 Steuergerät<br />
<br />
<br />
Resetting Service Reminders (SRI) is one function that is affected by the changes that VW/Audi have made relating to SFD/SFD2 and UNECE R155/R156. These measures can prevent changes or even block access to the vehicle. VCDS should be able to read all control modules and read all Adaptation channels even in the latest vehicles, but making changes (such as resetting service reminders) can become complicated.<br />
<br />
Let's start with the older vehicles, typically pre-2020, which lack SFD. <br />
<br />
Case 1 - No SFD: Just reset the service reminder using VCDS: https://www.ross-tech.com/vcds/tour/sri-reset.php<br />
<br />
Case 2 - SFD: When SFD was firsts introduced for example in the MEB (VW ID.4, etc.) or MQBevo (Golf 8, etc.) some modules have SFD such as 5F in the MEB and 17 in the MQBevo. This means to save Adaptation values to reset the service reminder, you would first need to unlock SFD in the module you are trying to change. This can be done with an offline token, like one from one of our German distributors: https://shop.pci-diagnosetechnik.de/SFD-Unlock-Base-Rate-incl-1-Control-Unit<br />
After that is unlocked (it stays unlocked for 90 minutes) then SRI Reset can proceed as normal. This process will need to be done again with a new SFD token at the next service reminder.<br />
<br />
Case 3 - SFD with Diagnostic Filter on the Gateway. This development came along with for example the 2024+ ID.4 which not only has SFD on some modules, but also has an SFD equipped CAN Gateway that contains an Adaptation channel for a diagnostic filter. By default, this filter prevents viewing other modules in the cars, let alone making changes in them. VCDS contains a workaround (R-Mode) that allows reading all of the modules and their info without first unlocking SFD but any changes will be blocked. In order to make changes in any modules in one of these vehicles, the first step would be to unlock SFD in 19-CAN Gateway (for example using an offline token like one purchased through the link above in Case 2). After 19 is unlocked, an Adaptation channel like this in 19-CAN Gateway can be changed: DE16611-Diagnosis filter: temporary deactivation adapted from active to not active. That turns off the filter which remains off for 20km. Next, the other modules in the car should be accessible without using R-Mode but any SFD modules will still prevent changes from being made. For example to reset the service reminder in the 2024 ID.4 the next step would be to go into address 5F and unlock SFD (using another token) then proceed to save the Adaptation channel(s) to reset SRI. Note that since R-Mode allow you to read data even in modules that the Gateway is filtering, it should be possible to read the SFD challenge from both 19-CAN Gateway and 5F while everything is still locked, to then order BOTH offline SFD tokens at the same time.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=User:Andy&diff=9723
User:Andy
2025-07-01T20:52:06Z
<p>Andy: </p>
<hr />
<div><font color=red>This is my test page please leave it alone</font> ;-)<br />
<br />
<br />
{| role="Presentation" class="wikitable" style="background:lightgray; text-align:center; width:99%" "border="0"<br />
|-<br />
! !! No SFD !! SFD in 17 !! SFD in 5F !! SFD2 / Filter<br />
|-<br />
! Service Reset<br />
| style="background:limegreen" | Just Perform SRI || style="background:orange" | Unlock SFD in 17 || style="background:orange" | Unlock SDF in 5F|| style="background:red" | Unlock SFD in 19<br />
|-<br />
! Unlock SFD?<br />
| style="background:limegreen" | No || style="background:orange" | Yes || style="background:red" | Yes || style="background:red" | Not Supported<br />
|-<br />
! Change Adaptation Channel<br />
| style="background:limegreen" | No || style="background:orange" | Original/Car PIN needed || style="background:orange" | Original/Car PIN needed || style="background:red" |N/A<br />
|-<br />
|}<br />
<br />
NI0<br />
- Ohne UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI1<br />
- Mit UNECE Cyber-Security Schutz<br />
- Mit UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI7<br />
- Mit UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Ohne SFD2 Steuergerät<br />
<br />
NI8<br />
- Ohne UNECE Cyber-Security Schutz<br />
- Ohne UNECE Software-Update Schutz<br />
- Mit SFD2 Steuergerät<br />
<br />
NI9 <br />
- Mit UNECE Cyber-Security Schutz (für Länder ohne UNECE Anforderungen)<br />
- Mit UNECE Software-Update Schutz (für Länder ohne UNECE Anforderungen)<br />
- Ohne SFD2 Steuergerät</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=User:Andy&diff=9722
User:Andy
2025-07-01T18:29:11Z
<p>Andy: Created page with "<font color=red>This is my test page please leave it alone</font> ;-)"</p>
<hr />
<div><font color=red>This is my test page please leave it alone</font> ;-)</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Official_Factory_Repair_Information&diff=9695
Official Factory Repair Information
2025-04-09T19:33:28Z
<p>Andy: </p>
<hr />
<div>'''Official Factory Repair Information for VW, Audi, Seat, Skoda and VAG based Bentley products is available directly from the manufacturers.''' erWin does include Repair Manuals, Wiring Diagrams, Technical Service Bulletins (TSB) / Technical Product Information (TPI), Vehicle Identification (by VIN) and much more. These sources are broken down by vehicle market including RoW and NAR:<br><br />
<br><br />
<br />
The '''RoW''' ('''Rest of World''') market vehicles use the following sources to purchase a subscription to the appropriate erWin websites:<br />
* [https://audi.erwin-store.com/erwin/showHome.do erWin Audi]<br />
** Users in Australia should see the note below before subscribing.<br />
* [https://volkswagen.erwin-store.com/erwin/showHome.do erWin VW]<br />
* [https://seat.erwin-store.com/erwin/showHome.do erWin Seat]<br />
* [https://skoda.erwin-store.com/erwin/showHome.do erWin Skoda]<br />
* [https://bentleymotors.erwin-store.com/erwin/showHome.do erWin Bentley Motors]<br />
* [https://lamborghini.erwin-store.com/erwin/showHome.do erWin Lamborghini]<br />
* [https://man.erwin-store.com/erwin/showHome.do erWin MAN] & [https://www.manserviceportal.eu MAN Service Portal]<br />
<br><br />
<br><br />
The '''NAR''' ('''North American Region''') ''including USA and Canadian'' market vehicles use the following sources to purchase a subscription to the appropriate erWin websites:<br />
* [https://vw-us.erwin-store.com/erwin/showHome.do erWin VW]<br />
* [https://audi-us.erwin-store.com/erwin/showHome.do erWin Audi]<br />
* [https://bentleymotors-us.erwin-store.com/erwin/showHome.do erWin Bentley Motors]<br />
* [https://lamborghini.erwin-store.com/erwin/showHome.do erWin Lamborghini]<br />
<br><br />
<br><br />
----<br />
<br><br />
'''NAR''' ('''North American Region''') Notes:<br />
* Sources such as Bentley Publisher's SSP (Self-Study Programs) are not a substitute for factory repair manuals but they are extremely helpful:<br />
** [http://www.bentleypublishers.com/volkswagen/technical-training Volkswagen Technical Training and Other Literature]<br />
** [http://www.bentleypublishers.com/Audi/technical-training Audi Technical Training and Other Literature]<br />
<br><br />
'''Australia Region''' Notes:<br />
* The Australian market may be prohibited from technical information via the erWin services due to safety concerns. Please see the following forum post:<br />
** https://forums.ross-tech.com/index.php?threads/44224<br />
<br><br />
<br />
'''Immobilizer and Pass-Thru''' (J2534) Notes:<br />
* erWin offers some Immobilizer operation solutions to independent repair facilities using one of the authorized Pass-Thru (J2534) devices on their list. Additional subscription based information can be obtained using the main [http://www.erwin-portal.com erWin portal] or any of the brand/market specific links above. Some of these operations include Immobilizer 4C and newer component adaptation and flash updates that are available with a specific Pass-Thru TSB/TPI. For 2010 or newer models, it should be possible to use ODIS [https://erwin.volkswagen.de/erwin/showInfoTour3.do] to perform immobilizer operations using either a Pass-Thru (J2534) device or one of VW's proprietary tools such as a VAS 6154 (WLAN-enabled), VAS 5054 (wireless via Bluetooth) or VAS 5055 (cable via USB connection). VCDS is NOT able to be used as a Pass-Thru and as explained on the [[Immobilizer]] Page, even if you have PIN code(s), VCDS is not able to perform most procedures in challenge-type Immobilizer systems.<br />
<br />
<br><br />
<br><br />
'''Parts Catalog and Vehicle Information''':<br />
* [http://www.partslink24.com partslink24] is the official Volkswagen, Audi, Seat and Skoda Parts Catalog for independent shops as well as private individuals. It does allow Vehicle Identification (via VIN) and highlights compatible parts accordingly. In addition it allows you to retrieve the complete production code information for a car (via VIN). These PR-Codes come in very handy for coding control modules, retrofits and other procedures.<br />
<br />
<br><br />
<br><br />
'''General''' Notes:<br />
* How to read current flow wiring diagram videos can be located in [https://forums.ross-tech.com/showthread.php?2884-How-to-read-wiring-diagrams-the-videos-(final-version) this thread].<br />
<br />
* '''Bosch''' Repair Manuals and Other Literature can be purchased from Bentley Publisher's:<br />
** [http://www.bentleypublishers.com/bosch Bosch Repair Manuals and Other Literature]<br />
<br></div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Talk:B2013&diff=9549
Talk:B2013
2024-07-17T18:59:46Z
<p>Andy: </p>
<hr />
<div>How does this work?<br />
Can I edit it?<br />
<!-- This is a comment that will not be shown to end users --></div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Talk:B2013&diff=9548
Talk:B2013
2024-07-17T18:59:06Z
<p>Andy: </p>
<hr />
<div>How does this work?<br />
Can I edit it?</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Official_Factory_Repair_Information&diff=9403
Official Factory Repair Information
2023-10-13T18:35:06Z
<p>Andy: </p>
<hr />
<div>'''Official Factory Repair Information for VW, Audi, Seat, Skoda and VAG based Bentley products is available directly from the manufacturers.''' erWin does include Repair Manuals, Wiring Diagrams, Technical Service Bulletins (TSB) / Technical Product Information (TPI), Vehicle Identification (by VIN) and much more. These sources are broken down by vehicle market including RoW and NAR:<br><br />
<br><br />
<br />
The '''RoW''' ('''Rest of World''') market vehicles use the following sources to purchase a subscription to the appropriate erWin websites:<br />
* [https://erwin.audi.com/erWinAudi erWin Audi]<br />
* [https://erwin.volkswagen.de/erWinVW erWin VW]<br />
* [https://erwin.seat.com/erWinSeat erWin Seat]<br />
* [https://erwin.skoda-auto.cz erWin Skoda]<br />
* [https://erwin.bentleymotors.com erWin Bentley Motors]<br />
* [https://erwin.lamborghini.com erWin Lamborghini]<br />
* [https://erwin.man.eu erWin MAN] & [https://www.manserviceportal.eu MAN Service Portal]<br />
<br><br />
<br><br />
The '''NAR''' ('''North American Region''') ''including USA and Canadian'' market vehicles use the following sources to purchase a subscription to the appropriate erWin websites:<br />
* [https://erwin.vw.com/erwin/showHome.do erWin VW]<br />
* [https://erwin.audiusa.com/erwin/showHome.do erWin Audi]<br />
* [https://erwinusa.bentleymotors.com/erwin/showHome.do erWin Bentley Motors]<br />
* [https://erwin.lamborghini.com erWin Lamborghini]<br />
<br><br />
<br><br />
----<br />
<br><br />
'''NAR''' ('''North American Region''') Notes:<br />
* Sources such as Bentley Publisher's SSP (Self-Study Programs) are not a substitute for factory repair manuals but they are extremely helpful:<br />
** [http://www.bentleypublishers.com/volkswagen/technical-training Volkswagen Technical Training and Other Literature]<br />
** [http://www.bentleypublishers.com/Audi/technical-training Audi Technical Training and Other Literature]<br />
<br><br />
<br />
'''Immobilizer and Pass-Thru''' (J2534) Notes:<br />
* erWin offers some Immobilizer operation solutions to independent repair facilities using one of the authorized Pass-Thru (J2534) devices on their list. Additional subscription based information can be obtained using the main [http://www.erwin-portal.com erWin portal] or any of the brand/market specific links above. Some of these operations include Immobilizer 4C and newer component adaptation and flash updates that are available with a specific Pass-Thru TSB/TPI. For 2010 or newer models, it should be possible to use ODIS [https://erwin.volkswagen.de/erwin/showInfoTour3.do] to perform immobilizer operations using either a Pass-Thru (J2534) device or one of VW's proprietary tools such as a VAS 6154 (WLAN-enabled), VAS 5054 (wireless via Bluetooth) or VAS 5055 (cable via USB connection). VCDS is NOT able to be used as a Pass-Thru and as explained on the [[Immobilizer]] Page, even if you have PIN code(s), VCDS is not able to perform most procedures in challenge-type Immobilizer systems.<br />
<br />
<br><br />
<br><br />
'''Parts Catalog and Vehicle Information''':<br />
* [http://www.partslink24.com partslink24] is the official Volkswagen, Audi, Seat and Skoda Parts Catalog for independent shops as well as private individuals. It does allow Vehicle Identification (via VIN) and highlights compatible parts accordingly. In addition it allows you to retrieve the complete production code information for a car (via VIN). These PR-Codes come in very handy for coding control modules, retrofits and other procedures.<br />
<br />
<br><br />
<br><br />
'''General''' Notes:<br />
* How to read current flow wiring diagram videos can be located in [https://forums.ross-tech.com/showthread.php?2884-How-to-read-wiring-diagrams-the-videos-(final-version) this thread].<br />
<br />
* '''Bosch''' Repair Manuals and Other Literature can be purchased from Bentley Publisher's:<br />
** [http://www.bentleypublishers.com/bosch Bosch Repair Manuals and Other Literature]<br />
<br></div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Cruise_Control_Retrofitting_(9N)&diff=9399
Cruise Control Retrofitting (9N)
2023-09-12T14:57:53Z
<p>Andy: </p>
<hr />
<div>__FORCETOC__<br />
<br />
== Requirements ==<br />
=== Central Electronics Control Module ===<br />
<br />
There are 3 Types of Central Electronic Control Modules (J519 / #09), only 2 of them support Cruise Control. The installed Type can easily be determined by the Control Module Part Number. ''Higher equipped Types always include the Options from the lower equipped ones.''<br><br />
<br />
* '''Basis'''<br />
** '''''Part Numbers''''': 6Q2-937-049-***<br />
* '''Medium'''<br />
** '''''Part Numbers''''': 6Q1-937-049-***<br />
** '''''Supported Features''''': Cruise Control System (CCS), Heated Front Window<br />
* '''High'''<br />
** '''''Part Numbers''''': 6Q0-937-049-***<br />
** '''''Supported Features''''': Automatic Transmission (Shift Lock),<br />
<br />
<br />
=== Engine Control Module ===<br />
<br />
Some Engines were never available with Cruise Control from Factory but may still support the Configuration/Activation. The following List contains some of those Exceptions and if they support Cruise Control or not. ''Engines NOT listed here are assumed to support Cruise Control, exceptions may exist. ;-)''<br><br />
<br />
* 1.2l MPI AWY (47 kW / Simos 3PD)<br />
** Cruise Control NOT supported, this Function was never available from Factory!<br />
** The Control Module MAY accept the Activation but will not Function!<br />
* 1.2l MPI BBM (44 kW / Simos 9.1)<br />
** Cruise Control supported even though this Function was never available from Factory!<br />
<br />
<br />
== Installation & Wiring ==<br />
<br />
Please refer to Repair Manuals, Wiring Diagram, Parts Catalog and/or the Instructions included in the Retrofitting Kit for Details.<br />
<br />
<br />
== Configuration ==<br />
<br />
The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use.<br />
<br />
* Update the Engine Control Module (J623 / #01) Login/Coding-2<br />
** ''Due to different Control Modules and Equipment in the Car the actual Login/Coding-2 Table is not shown here but will automatically be shown once you access the Function using VCDS.''<br />
<br />
<br />
'''''If you are having trouble with the Configuration/Activation then please see the [[Retrofitting]] page.''</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Throttle_Body_Alignment_(TBA)&diff=9393
Throttle Body Alignment (TBA)
2023-08-31T13:17:11Z
<p>Andy: </p>
<hr />
<div><br><br />
Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!<br />
<br><br />
<br><br />
This procedure details how to perform a Throttle Body Alignment (TBA) on many VW/Audi vehicles with Gasoline engines. This procedure cycles the motorized throttle body through various states (idle, part throttle, WOT) to relearn their positions. Some examples of reasons to perform a TBA:<br />
<br><br />
<br><br />
*The vehicle's battery has been disconnected and re-connected<br />
*The ECU has been removed and reinstalled<br />
*The Throttle Body has been cleaned or removed and reinstalled<br />
*The Accelerator Pedal has been removed and reinstalled<br />
<br><br />
In some vehicles, the car will not run correctly, or may not run at all without performing a TBA after one of the above operations. The TBA can be performed on both Drive-By-Wire (DBW or E-gas) as well as Cable-throttle cars as long as there is no Idle Stabilization Valve (ISV). If there is an ISV, then there is no motorized control of the throttle at all. Typically, '96-'99 VW/Audi have motorized Cable-throttle, and '00+ VW/Audi have DBW. Obviously, there are some exceptions. This should be obvious but '''older, pre-Common-Rail TDI's do not have throttle bodies'''.<br />
<br><br />
There are certain test conditions that must be met before doing a TBA:<br />
*No DTC's in the Engine Controller<br />
*Battery voltage at least 11.5 V<br />
*Throttle must be at idling position (keep your foot off the gas pedal)<br />
*Throttle body part must not be dirty (carbonized).<br />
*Coolant temperature must be between 5 and 95C<br />
* If fault codes were cleared cycle the ignition off and back on prior to running Basic Settings.<br />
<br><br />
== Cable-Throttle Engines == <br />
(These are engines with a physical cable between the accelerator and the throttle, but WITHOUT an ISV.)<br />
<br> <br />
<br><br />
Turn the key on but do not start the car.<br />
<br><br />
*'''[Select]'''<br />
*'''[01 - Engine]'''<br />
*'''[Basic Settings - 04]'''<br />
Enter Group '''098''' (Note: Some SIMOS or Marelli ECU's use Group 001 such as ADY & [http://wiki.ross-tech.com/wiki/images/1/18/AEE_Throttle_body_info.jpg AEE] engines)<br />
*'''[Go!]'''<br />
<br />
Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switch to basic settings. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.<br />
*Click the '''[Switch to Meas. Blocks]''' button and you're all set.<br />
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!<br />
<br />
== Drive-by-Wire (DBW) Engines using KW-1281 == <br />
(These are engines WITHOUT a physical cable between the accelerator and the throttle. Check to see if the engine speaks KW-1281 by looking in the top left of the Open Controller Screen Some examples of KW-1281 engine controllers are 2000+ Golf/GTI/Jetta/New Beetle/Audi TT 1.8T)<br />
<br> <br />
<br><br />
Turn the key on but do not start the car.<br />
<br><br />
*'''[Select]'''<br />
*'''[01 - Engine]'''<br />
*'''[Basic Settings - 04]'''<br />
Enter Group '''060'''<br />
*'''[Go!]'''<br />
<br />
Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switch to basic settings. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.<br />
*'''[Switch to Meas. Blocks]''' button and you're all set.<br />
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!<br />
<br />
== Drive-by-Wire (DBW) Engines using KWP-2000 or CAN == <br />
(These are engines WITHOUT a physical cable between the accelerator and the throttle. Check to see if the engine speaks KWP-2000 or CAN by looking in the top left of the Open Controller Screen. An example of a KWP-2000 engine controller is the 2002+ B6 Audi A4 1.8T. Some examples of CAN engine controllers are the Mk5 Golf 2.0T FSI)<br />
<br> <br />
<br><br />
Turn the key on but do not start the car.<br />
<br><br />
*'''[Select]'''<br />
*'''[01 - Engine]'''<br />
*'''[Basic Settings - 04]'''<br />
*Group '''060'''<br />
*'''[Go!]'''<br />
It should say "Basic Settings: OFF" on the top of your screen.<br />
*Click '''[ON/OFF/Next]''' to turn on Basic Settings.<br />
It should now say "Basic Settings: ON" on the top of your screen. Once you do this you will see the top right display say ADP RUN. The TB adaptation is being done as soon as you switched basic settings on. You will see the values change and hear the TB cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.<br />
*Click ['''ON/OFF/Next]''' to turn off Basic Settings.<br />
It should now say "Basic Settings: OFF" on the top of your screen<br />
*Click the '''[Done, Go Back]''' button and you're all set.<br />
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!<br><br />
<br><br />
If it did not complete, or resulted in Error, see the Special Notes below.<br />
<br><br />
<br><br />
<br />
== Drive-by-Wire (DBW) Engines using KWP-7000 (UDS/ODX) ==<br />
Check to see if the engine speaks KWP-2000 or CAN by looking in the top left of the Open Controller Screen. UDS modules do not support conventional Measuring Blocks - 08 so that button will be grayed out. They do not support conventional Adaptation - 10 or Basic Settings - 04 group numbers, so all choices are found in drop-down menus in these modules.<br />
<br> <br />
<br><br />
Make sure the coolant is warm. Turn the key on but do not start the car.<br />
<br><br />
*'''[Select]'''<br />
*'''[01 - Engine]'''<br />
*'''[Basic Settings - 04]'''<br />
* Choose a variant of '''Throttle Valve Adaptation''' from the drop-down list<br />
*'''[Go!]''' to activate the Basic Settings<br><br />
* After the result of '''Finished Correctly''' appears click '''[Stop]'''<br />
The TB may cycle for the first few seconds then it will stop. Leave it in Basic Settings for about 30 seconds.<br />
*Click the '''[Done, Go Back]''' button and you're all set.<br />
Be sure not to touch the accelerator and make sure the engine is NOT running when you do this!<br><br />
<br><br />
<br />
==== Special Notes ====<br />
<br />
* In some engines, before doing a TBA, it may be necessary to cycle the ignition off and back on after clearing faults.<br />
* On vehicles that use Cable-Throttle systems, an over adjusted (or sticky) throttle cable can cause the TBA to fail, or symptoms like no CCS (Cruise Control System) operation.<br />
* On vehicles that use Cable-Throttle systems the idle may be erratic after the TB has been removed and cleaned, even after a successful TBA. It may be necessary to drive the vehicle normally for a while until the system has re-adapted.<br />
<br />
== Video Link ==<br />
<br />
[[File:Throttlebody.jpg|200px|link=http://www.youtube.com/watch?v=2zrmhDw_v7Y]]<br />
http://www.youtube.com/watch?v=2zrmhDw_v7Y</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Audi_A6_(4B)_Instrument_Cluster_(from_MY_2000)&diff=9325
Audi A6 (4B) Instrument Cluster (from MY 2000)
2022-09-15T18:33:46Z
<p>Andy: </p>
<hr />
<div>__FORCETOC__<br />
== Coding ==<br />
<br />
* '''??xxx''': ''Options''<br />
** +01 = Larger Fuel Tank (80 liters for 8-Cylinder Quattro and S6)<br />
** +02 = Seatbelt Warning active<br />
** +04 = Tires for Allroad (MY 2002+)<br />
** +16 = Seatbelt Warning active (in some cases, try this if +02 doesn't work)<br />
* '''xx?xx''': ''Country''<br />
** 0 = Germany<br />
** 1 = Rest of World (Left Hand Drive)<br />
** 2 = USA<br />
** 3 = Canada<br />
** 4 = Great Britain<br />
** 5 = Japan (Left Hand Drive)<br />
** 6 = Arabian States<br />
** 7 = Australia and New Zealand<br />
** 8 = Rest of World (Right Hand Drive)<br />
** 9 = Japan (Right Hand Drive)<br />
* '''xxx??''': Engine<br />
** 40 = 4-Cylinder Diesel<br />
** 42 = 4-Cylinder Gasoline<br />
** 44 = 4-Cylinder Gasoline Turbo<br />
** 60 = 6-Cylinder Diesel<br />
** 62 = 6-Cylinder Gasoline<br />
** 64 = 6-Cylinder Gasoline Turbo<br />
** 83 = 8-Cylinder Gasoline<br />
<br />
<br />
== Adaptation ==<br />
=== Channel 004: Language ===<br />
* 1 = German<br />
* 2 = English<br />
* 3 = French<br />
* 4 = Italian<br />
* 5 = Spanish<br />
* 6 = Portuguese</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Fuel_Trim_Info&diff=9295
Fuel Trim Info
2022-06-02T15:21:03Z
<p>Andy: </p>
<hr />
<div>'''Understanding Fuel Trim'''<br />
<br><br />
<br><br />
Some of the most common [[:Category:Fault Codes|Fault Codes (DTC's)]] pertain to fuel trim (rich mixture, lean mixture, etc.) Here is an explanation of fuel trim and what it does for us. The ECU controls Air/Fuel mixture in order to maintain power, efficiency, and emissions. A/F is expressed as either a ratio (14.7:1 for example) or as a Lambda value. With iso-octane ("ideal" gasoline), Lambda of 1.0 is equal to 14.7:1 A/F. This is known as "Stoichiometric", a condition where there is a perfect balance between oxygen molecules and the various hydrogen and carbon based molecules in petroleum. With the oxygenated gasoline that most of us use, actual A/F ratio of 15:1 is closer to stoichiometric.If Lambda is greater than 1.0, then there is a surplus of air and the engine is running lean. If Lambda is less than 1.0, then there is a surplus of fuel and the engine is running rich. It should be noted that the ratios are mass-based, not volume-based.<br />
<br><br />
<br><br />
So, why don't we always run at 1.0 all the time? Well, we do MOST of the time. At cruise and idle, mixture is held tightly to 1.0 to keep the catalytic convertor at optimal efficiency, so the emissions are minimized. However, when we need acceleration, the mixture gets richer. Why? Maximum power is made between 0.85 to 0.95 Lambda (12.5 to 14.0 A/F with iso-octane). So, under acceleration, mixtures get richer. Sometimes you want to get even richer under acceleration to keep detonation (pre-ignition of the mixture from excess cylinder temperatures) away. The 1.8T has a relatively high compression ratio for a turbocharged engine, which especially under lots of boost, is very succeptible to detonation).<br />
<br><br />
<br><br />
So, now that we know that the ECU wants to be able to control the A/F ratio. It has a prescribed set of values (maps) for a given RPM, Load, etc. So, the ECU tells the injectors to pulse for exactly XX.X milliseconds and that SHOULD get us the proper A/F ratio that we want. Well, if you tell an employee to go do something, you want to make sure they actually did it, right? The ECU has some snitches (the front O2 sensor and the MAF, for the most part) that will report back whether or not the desired mixture has been attained. The rear O2 sensor is used mostly to monitor the condition of the catalytic convertor, although in some applications it also contributes to trim information.<br />
<br><br />
<br><br />
Based on feedback from the snitches, the ECU learns to apply a correction factor to its commands to the fuel injectors. If you know that your employees take longer than the standard allotted time to do a specified job, you will need to adjust for that in your planning (injectors are in a union, so it is tough to fire them ). The learned values go between the maps in the ECU's Flash ROM (the "chip") and the signal to the fuel injectors. These learned compensations are known as "trim". So, when you see "trim", it means "compensation".<br />
<br><br />
<br> "Add" means additive trim, which is addressing an imbalance at idle. When the ECU is using additive trim, it is telling the injectors to stay open a fixed amount longer or shorter. The malfunction (e.g. vacuum leak) becomes less significant as RPM increase. For additive adaptation values, the injection timing is changed by a fixed amount. This value is not dependent on the basic injection timing.<br />
<br><br />
<br>"Mult" mean multiplicative trim, which is addressing an imbalance at all engine speeds. The malfunction (e.g. clogged injector) becomes more severe at increased RPM. For multiplicative adaptation values, there is a percentage change in injection timing. This change is dependent on the basic injection timing.<br />
<br><br />
<br> You can check your current state of trim by using VAG-COM or equivalent to look in Group 032 (in many modern ECU's, consult your Factory Repair Manual for the specific group for your particular vehicle) in your engine measuring blocks. The first two fields will have percentages. The first field tells the fuel trim at idle (Additive). The second field tells the fuel trim at elevated engine speeds (Multiplicative). Negative values indicate that the engine is running too rich and oxygen sensor control is therefore making it more lean by reducing the amount of time that the injectors are open. Positive values indicate that the engine is running too lean and oxygen sensor control is therefore making it richer by increasing the amount of time that the injectors are open.<br />
<br><br />
<br>It is totally normal for both the first and second fields to be something other than zero. In fact, zeros IN BOTH FIELDS indicates that either you just cleared codes (which will reset fuel trim values) or something isn't working properly. If values get too far away from zero, it will cause a DTC (fault code) and can set off the MIL (commonly referred to as the Check Engine Light, or CEL). Specifications for normal operation are usually somewhere near +/- 10%.<br />
<br><br />
<br>In general, an out-of-spec value in the first field (Additive) indicates a vacuum leak since it is mostly present at idle, when vacuum is highest. An out-of-spec value in the second field (Multiplicative) indicates a fault at higher RPM, and may point to a faulty MAF.<br />
<br><br />
<br><br />
When checking MVB 032, it is normal to not see the values change real-time (unless you clear DTCs while watching MVB 032). Instead, this is learned value over time. To see the ECU's real-time response to fuel system sensors, check MVB 033 which should show values moving around (for example when temporarily removing the dipstick to change how the PCV operates). The video at the bottom of this page explains this in more detail.<br />
<br><br />
<br>Here's a good sanity check for the status of your MAF. Do a full-throttle run all the way to redline in a single gear (second works fine). Group 002 usually shows air mass in g/s (in many modern ECU's, consult your Factory Repair Manual for the specific group for your particular vehicle). Your peak airflow should be roughly 0.80 times your horsepower if you are close to sea level. So, if you have a stock 150 hp 1.8T, expect around 120 g/s. If you see significantly less than that, you MAF may be on the way out. Also note that airflow will be markedly different at higher altitudes due to reduced ambient air pressure, especially with naturally aspirated engines that do not have forced induction to overcome that deficiency. This still works if you are chipped, but "race" programs may make more power through timing, rather than airflow. Therefore, take all readings with a grain of salt.<br />
<br><br />
<br />
[[User:Andy|Andy]] 11:30, 8 May 2006 (Eastern Standard Time)<br />
<br />
[[VAG-COM-FAQ-1.1]]<br />
<br />
== Video Link ==<br />
=== Fuel Trim ===<br />
<br />
[[File:thumb_fueltrim.jpg|200px|link=http://www.youtube.com/watch?v=yM3iarhSP68]]<br />
<br />
http://www.youtube.com/watch?v=yM3iarhSP68</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Audi_A3/S3_(8V/FF)&diff=9157
Audi A3/S3 (8V/FF)
2021-08-13T13:23:29Z
<p>Andy: </p>
<hr />
<div>This page will have information about the MQB 8V/FF A3/S3.<br />
<br />
----<br />
<br />
<br />
<br />
{{Infobox-Model<br />
|Brand=Audi<br />
|Model=A3<br />
|Image=Audi-A3-MQB.jpg<br />
|ImageSource=Ross-Tech, LLC<br />
|Manufacturer=Audi AG<br />
|ChassisCode= 8V / FF<br />
|Platform=AU37X<br />
|from=2013<br />
|through=<br />
|fromUS=2015<br />
|throughUS=<br />
|Predecessor=[[Audi A3/S3 & A3 Cabriolet (8P) ]]<br />
|Successor=-<br />
|Interface='''All model years''' [http://www.ross-tech.com/vcds/interfaces.php HEX-V2], [http://www.ross-tech.com/vcds/interfaces.php HEX-NET]<br />
''Limited 2013-2016 coverage [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php HEX+CAN], [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php Micro-CAN]''<br />
|DLCImage=DLC-Audi-A3-FF.jpg<br />
|DLC=The DLC is located in the Driver Footwell.<br />
}}<br />
<br />
=== [01] - Engine ===<br />
<br />
=== [02] - [[6-Speed Direct Shift Gearbox (DSG/0D9) | Auto Trans]] ===<br />
<br />
=== [03] - [[VW Golf VII (5G/AU) ABS Brakes | ABS Brakes]] ===<br />
* [[VW Golf VII (5G/AU) ABS Brakes#Basic_Setting|Basic Setting]]<br />
**''5Q0-907-379-IPB-V1.clb''<br />
**''EV_Brake1UDSContiMK100IPB_VW37''<br />
<br />
=== [05] - Access/Start Authorization ===<br />
<br />
=== [08] - Auto HVAC ===<br />
<br />
=== [09] - Cent. Elect. ===<br />
<br />
'''Note''': ''Before making ANY changes, you should run and Save a controller channel map of Adaptation in address 09. [[Control_Module_Maps]]<br />
<br />
=== [15] - [[AirbagVW20 | Airbags]] ===<br />
<br />
=== [16] - Steering Wheel ===<br />
<br />
=== [17] - [[VW Golf VII (5G/AU) Instrument Cluster | Instrument Cluster]] ===<br />
<br />
* [[VW Golf VII (5G/AU) Instrument Cluster#Service_Reminder|Service Reminder]]<br />
<br />
=== [19] - [[VW Golf VII (5G/AU) CAN Gateway|CAN Gateway]] ===<br />
<br />
=== [2B] - Steering Column Lock ===<br />
<br />
=== [42] - Door Elect, Driver ===<br />
<br />
=== [44] - Steering Assist === <br />
<br />
=== [52] - Door Elect, Pass ===<br />
<br />
=== [55] - Headlight Aim Control ===<br />
* LWR-ECU (vertical motors but no turning) with no slave modules<br />
* AFS-ECU (vertical motors and turning motors) with two slave modules<br />
** [[VW MQB Headlight Regulation]]<br />
* LED-AFS-ECU (vertical motors and turning motors) with four slave modules<br />
<br />
=== [5F] - Information Electronics ===<br />
<br />
=== [75] - Telematics ===<br />
<br />
=== [4B] - Multifunc. Module ===<br />
<br />
=== [A9] - Struct. Borne Sound ===</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Golf_VII_(5G/AU)&diff=9142
VW Golf VII (5G/AU)
2021-06-02T12:30:44Z
<p>Andy: /* [09] - Cent. Elect. */</p>
<hr />
<div>This page will have information about the Golf 7.<br />
<br />
These pages have some information on tweaks for the Mk7 Golf platform vehicles:<br />
<br />
http://forums.ross-tech.com/showthread.php?512-MQB-Platform-tweaks<br />
<br />
http://www.golfgtiforum.co.uk/index.php?topic=260248.0<br />
<br />
http://vcds.greg-roberts.com/view-entries<br />
<br />
http://forums.vwvortex.com/showthread.php?7013354<br />
<br />
http://forums.vwvortex.com/showthread.php?7231270<br />
<br />
https://sites.google.com/a/naturalnetworks.ca/vw-golf-mk7-vcds-how-to/<br />
<br />
http://forums.vwvortex.com/showthread.php?8687226-VCDS-coding-on-an-Alltrack<br />
<br />
----<br />
<br />
<br />
<br />
{{Infobox-Model<br />
|Brand=Volkswagen<br />
|Model=Golf VII<br />
|Image=VW-Golf-VII.jpg<br />
|ImageSource=Ross-Tech, LLC<br />
|Manufacturer=Volkswagen AG<br />
|ChassisCode= 5G / AU<br />
|Platform=VW37X<br />
|from=2013<br />
|through=<br />
|fromUS=2015<br />
|throughUS=<br />
|Predecessor=[[VW Golf/Golf Plus (5K/52)]]<br />
|Successor=-<br />
|Interface='''All model years''' [http://www.ross-tech.com/vcds/interfaces.php HEX-V2], [http://www.ross-tech.com/vcds/interfaces.php HEX-NET]<br />
''Limited 2016+ RoW market coverage [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php HEX+CAN], [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php Micro-CAN]''<br />
|DLCImage=DLC-VWGolf5G.jpg<br />
|DLC=The DLC is located in the Driver Footwell.<br />
}}<br />
<br />
=== [01] - Engine ===<br />
<br />
=== [02] - [[6-Speed Direct Shift Gearbox (DSG/0D9) | Auto Trans]] ===<br />
<br />
=== [03] - [[VW Golf VII (5G/AU) ABS Brakes | ABS Brakes]] ===<br />
* [[VW Golf VII (5G/AU) ABS Brakes#Basic_Setting|Basic Setting]]<br />
**''5Q0-907-379-IPB-V1.clb''<br />
**''EV_Brake1UDSContiMK100IPB_VW37''<br />
* G85 is calibrated in Address 44. See [https://forums.ross-tech.com/showthread.php?4224-MQB-(Mk7-Golf)-Steering-Angle-Sensor-(G85)-Calibration-in-44-Steering-Assist&p=144324&viewfull=1#post144324 this post]<br />
<br />
=== [05] - Access/Start Authorization ===<br />
<br />
=== [08] - Auto HVAC ===<br />
<br />
=== [09] - Cent. Elect. ===<br />
<br />
'''Note #1''': ''Before making ANY changes, you should run and Save a controller channel map of Adaptation in address 09. [[Control_Module_Maps]]<br><br />
'''Note #2''': ''Starting around model year 2018 many BCM/CECM modules show all zeros for Coding. In these applications, Coding is neither necessary nor possible. Instead changes are made using Adaptation as discussed here: https://forums.ross-tech.com/index.php?threads/10616/<br><br />
'''Note #3''': ''In some of the latest models, you need to open the hood to make changes due to the Diagnostic Firewall that is discussed here:<br />
https://forums.ross-tech.com/index.php?threads/15536/<br />
<br />
=== [15] - [[AirbagVW20 | Airbags]] ===<br />
<br />
=== [16] - Steering Wheel ===<br />
<br />
=== [17] - [[VW Golf VII (5G/AU) Instrument Cluster | Instrument Cluster]] ===<br />
<br />
* [[VW Golf VII (5G/AU) Instrument Cluster#Service_Reminder|Service Reminder]]<br />
<br />
=== [19] - [[VW Golf VII (5G/AU) CAN Gateway|CAN Gateway]] ===<br />
<br />
=== [2B] - Steering Column Lock ===<br />
<br />
=== [42] - Door Elect, Driver ===<br />
<br />
=== [44] - Steering Assist === <br />
<br />
=== [52] - Door Elect, Pass ===<br />
<br />
=== [55] - [[VW MQB Headlight Regulation|Headlight Aim Control]] ===<br />
* [[VW MQB Headlight Regulation#Coding|Coding]]<br />
* [[VW MQB Headlight Regulation#Coding|Basic Setting]]<br />
<br />
=== [5F] - Information Electronics ===<br />
<br />
=== [75] - Telematics ===<br />
<br />
=== [A9] - Struct. Borne Sound ===</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Common_Acronyms&diff=8970
Common Acronyms
2021-01-21T20:41:41Z
<p>Andy: </p>
<hr />
<div>{| style="background:#efefef;text-align:center;" border="1" width="100%" class="notranslate"<br />
|-<br />
! Acronym<br>(English) !! Acronym<br>(German) !! Meaning (English / ''German'')<br />
|-<br />
! ACC<br />
| ADR || Adaptive Cruise Control / ''Adaptive Geschwindigkeitsregelung / Adaptive Distanzregelung''<br />
|-<br />
! ADL<br />
| AFL || Assistant Driving Light / ''Assistenzfahrlicht''<br> Automatic Headlamp Activation / ''Automatische Fahrlichtschaltung''<br />
|-<br />
! ADS<br />
| || Audi Drive Select (Charisma)<br />
|-<br />
! AID<br />
| || Active Info Display (VW Digital Cockpit/ Audi Virtual Cockpit)<br />
|-<br />
<br />
! ATA<br />
| DWA || Anti-Theft Alarm / ''Diebstahlwarnanlage''<br />
|-<br />
! <br />
| AWV || Stopping Distance Shortening / ''Anhaltewegverkürzung''<br />
|-<br />
! BAP<br />
| BAP || Operating and Display Protocol / ''Bedien- und Anzeigeprotokoll''<br />
|-<br />
! BCM<br />
| || Body Control Module<br />
|-<br />
! BCmE<br />
| BCmE || Board Computer with Efficiency Program / ''Bordcompter mit Effizienzprogramm''<br />
|-<br />
! <br />
| BKV || Brake Booster / ''Bremskraftverstärker''<br />
|-<br />
! <br />
| BVA || Break Pad Wear Indicator / ''Bremsbelagverschleißanzeige''<br />
|-<br />
! CCS<br />
| GRA || Cruise Control System / ''Geschwindigkeitsregelanlage''<br />
|-<br />
! CL<br />
| ZV || Centeral Locking / ''Zentralverriegelung''<br />
|-<br />
! CVT<br />
| || Continuously Variable Transmission / ''Stufenloses Getriebe''<br />
|-<br />
! DCC<br />
| || Dynamic Chassis Control / ''Dynamische Dämpfungsregelung''<br />
|-<br />
! DDP<br />
| DDP || Display-Data-Protocol / ''Display-Daten-Protokoll''<br />
|-<br />
! DRC<br />
| || Dynamic Ride Control / ''Dynamische Dämpfungsregelung''<br />
|-<br />
! DLA<br />
| || Dynamic Light Assist<br />
|-<br />
! DRL<br />
| TFL || Daytime Running Light / ''Tagfahrlicht''<br />
|-<br />
! DSD<br />
| || Dynamic Standstill Detection<br />
|-<br />
! DSG<br />
| DSG || Direct-Shift Gearbox / ''Direktschaltgetriebe''<br />
|-<br />
! DTC<br />
| || Diagnostic Trouble Code / ''Fehlernummer''<br />
|-<br />
! EBC<br />
| MSR || Engine Braking Control / ''Motor-Schleppmoment-Regelung''<br />
|-<br />
! <br />
| eBKV || Electric Brake Booster / ''Elektrischer Bremskraftverstärker''<br />
|-<br />
! ECD<br />
| || Electronic Controlled Deceleration<br />
|-<br />
! ECM<br />
| MSG || Engine Control Module / ''Motorsteuergerät''<br />
|-<br />
! EPB<br />
| EFB || Electric Parking Brake / ''Elektrische Feststellbremse''<br />
|-<br />
! EPS<br />
| LKH || Electro Mechanical Power Steering / ''Elektromechanische Lenkhilfe''<br />
|-<br />
! ESCL<br />
| ELV || Electronic Steering Column Lock / ''Elektrische Lenksäulenverriegelung''<br />
|-<br />
! ESI<br />
| WIV || Extended Service Interval / ''Wartungsintervallverlängerung''<br>Flexible Service Interval / '' Flexible Wartungsintervallanzeige''<br />
|-<br />
! FMA<br />
| || Fuel Mean Value Adaptation / ''Kraftstoffmengen-Mittelwertadaptation''<br />
|-<br />
!<br />
| FMA || Freewheeling Motor Off (Start-Stop with Coasting) / ''Freilauf Motor Aus''<br />
|-<br />
! FWH<br />
| FSH || Front Window Heating / ''Frontscheibenheizung''<br />
|-<br />
!<br />
| GLW || Sliding Light Width Control (part of DLA) / ''Gleitende LeuchtWeitenregelung''<br />
|-<br />
! <br />
| HBV || Hydraulic Brake Booster / ''Hydraulischer Bremskraftverstärker''<br />
|-<br />
! HCA/LDW<br />
| SHA || Heading Control Assist / Lane Departure Warning / ''Spurhalteassistent''<br />
|-<br />
! HDC<br />
| || Hill Descend Control / ''Bergabfahrhilfe''<br />
|-<br />
! IPB<br />
| IPB || Integrated Parking Brake / ''Integrierte Parkbremse''<br />
|-<br />
! HHC<br />
| || Hill Hold Control / ''Berganfahrhilfe''<br />
|-<br />
! LCA<br />
| SWA || Lane Change Assist / ''Spurwechselassistent''<br />
|-<br />
! <br />
| LWR || Luminous Width Regulation / ''Leucht Weiten Regulierung''<br />
|-<br />
!<br />
| MDF || Masked Long Distance Light (part of DLA) / ''Maskiertes Dauerfernlich''<br />
|-<br />
! MFD<br />
| MFA || Multi-Function Display / ''Multifunktionsanzeige''<br />
|-<br />
! MFSW<br />
| MFL || Multi-Function Steering Wheel/ ''Multifunktionslenkrad''<br />
|-<br />
! <br />
| MKE || Fatigue Recognition/ ''Müdigkeitserkennung''<br />
|-<br />
! MT<br />
| SG/HS || Manual Transmission / ''Schaltgetriebe oder Handschaltgetriebe''<br />
|-<br />
! OCU<br />
| || Onboard Communication Unit<br />
|-<br />
! PDC<br />
| EPH || Park Distance Control / ''Einparkhilfe''<br />
|-<br />
! <br />
| PLA || Park-Steer-Assist / ''Parklenkassistent''<br />
|-<br />
! <br />
| PSD || Predictive Route Data / ''Prädiktive Streckendaten''<br />
|-<br />
! PW<br />
| EFH || Power Windows / ''Elektrische Fensterheber''<br />
|-<br />
! RC<br />
| FFB || Remote Control / ''Funkfernbedienung''<br />
|-<br />
! <br />
| HAL || Rear Axle Steering / ''Hinterachslenkung''<br />
|-<br />
! RFL<br />
| NSL || Rear Fog Lamp / ''Nebelschlusslicht''<br />
|-<br />
! RL<br />
| RFL || Reverse Light / ''Rückfahrlicht''<br />
|-<br />
! RLFS<br />
| RLFS || Rain Light Humidity Sensor / ''Regen-/Licht-/Feuchtesensor''<br />
|-<br />
! RLS<br />
| RLS || Rain Light Sensor / ''Regen-/Lichtsensor''<br />
|-<br />
! ROP<br />
| || Roll Over Prevention/Protection / ''Überrollschutz''<br />
|-<br />
! RWU<br />
| || Rear Wheel Unlocker<br />
|-<br />
! <br />
| SMLS || Switch module for steering column / ''Schaltermodul der Lenksäule''<br />
|-<br />
! SRI<br />
| SIA || Service Reminder Indicator / ''Service-Intervall-Anzeige''<br />
|-<br />
! TCM<br />
| GSG || Transmission Control Module / ''Getriebesteuergerät''<br />
|-<br />
! TPL<br />
| || Technical Problem Solution (''also see TSB/TPI'') / ''Technische Problemlösung''<br />
|-<br />
! TPI<br />
| || Technical Product Information (''also see TSB/TPL'') / ''Technische Produktinformation''<br />
|-<br />
! TSB<br />
| || Technical Service Bulletin (''also see TPL/TPI'')<br />
|-<br />
! TPMS<br />
| RKA/RDK || Tire Pressure Monitoring System / ''Reifenkontrollanzeige oder Reifendruckkontrolle''<br />
|-<br />
! UGDO<br />
| || Universal Garage Door Opener / ''Universeller Garagentoröffner''<br />
|-<br />
! VSS<br />
| || Vehicle Speed Sensor<br />
|-<br />
! <br />
| VZA || Traffic Sign Display / ''Verkehrszeichen-Anzeige''<br />
|-<br />
! <br />
| VZE || Traffic Sign Recognition / ''Verkehrszeichen-Erkennung''<br />
|-<br />
! WSS<br />
| || Wheel Speed Sensor<br />
|-<br />
! <br />
| WWS || Wiper Angle Control (Wiper Motor) / ''Wischwinkelsteuerung (Wischermotor)''<br />
|-<br />
|}</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=P24D8&diff=8934
P24D8
2020-11-16T19:49:37Z
<p>Andy: Created page with "__FORCETOC__ == P24D8 EVAP Pressure Sensor 2: Short to Plus == ==== Possible Symptoms ==== * MIL on ==== Possible Causes ==== * EVAP Pressure Sensor (G950) faulty * EVAP Pre..."</p>
<hr />
<div>__FORCETOC__<br />
== P24D8 EVAP Pressure Sensor 2: Short to Plus ==<br />
<br />
==== Possible Symptoms ====<br />
* MIL on<br />
<br />
==== Possible Causes ====<br />
* EVAP Pressure Sensor (G950) faulty<br />
* EVAP Pressure Sensor (G950)<br />
<br />
==== Possible Solutions ====<br />
* Check EVAP Pressure Sensor (G950) sensor and wiring.<br />
* Note, this fault text corresponds to what is shown in the factory scan tool but may be partially incorrect (we think it should be " Pressure Sensor" instead of "Pressure Sensor 2". For example, in a 2019 Audi A6 3.0T with the DLZA engine, there is only one EVAP pressure sensor, not two. Unplugging the sensor G950 will set this fault. Some V8 applications may have multiple sensors and it's unclear if this fault is used with those or something different exists.<br />
<br />
<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Golf_VII_(5G/AU)&diff=8930
VW Golf VII (5G/AU)
2020-10-26T12:00:47Z
<p>Andy: /* [09] - Cent. Elect. */</p>
<hr />
<div>This page will have information about the Golf 7.<br />
<br />
These pages have some information on tweaks for the Mk7 Golf platform vehicles:<br />
<br />
http://forums.ross-tech.com/showthread.php?512-MQB-Platform-tweaks<br />
<br />
http://www.golfgtiforum.co.uk/index.php?topic=260248.0<br />
<br />
http://vcds.greg-roberts.com/view-entries<br />
<br />
http://forums.vwvortex.com/showthread.php?7013354<br />
<br />
http://forums.vwvortex.com/showthread.php?7231270<br />
<br />
https://sites.google.com/a/naturalnetworks.ca/vw-golf-mk7-vcds-how-to/<br />
<br />
http://forums.vwvortex.com/showthread.php?8687226-VCDS-coding-on-an-Alltrack<br />
<br />
----<br />
<br />
<br />
<br />
{{Infobox-Model<br />
|Brand=Volkswagen<br />
|Model=Golf VII<br />
|Image=VW-Golf-VII.jpg<br />
|ImageSource=Ross-Tech, LLC<br />
|Manufacturer=Volkswagen AG<br />
|ChassisCode= 5G / AU<br />
|Platform=VW37X<br />
|from=2013<br />
|through=<br />
|fromUS=2015<br />
|throughUS=<br />
|Predecessor=[[VW Golf/Golf Plus (5K/52)]]<br />
|Successor=-<br />
|Interface='''All model years''' [http://www.ross-tech.com/vcds/interfaces.php HEX-V2], [http://www.ross-tech.com/vcds/interfaces.php HEX-NET]<br />
''Limited 2016+ RoW market coverage [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php HEX+CAN], [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php Micro-CAN]''<br />
|DLCImage=DLC-VWGolf5G.jpg<br />
|DLC=The DLC is located in the Driver Footwell.<br />
}}<br />
<br />
=== [01] - Engine ===<br />
<br />
=== [02] - [[6-Speed Direct Shift Gearbox (DSG/0D9) | Auto Trans]] ===<br />
<br />
=== [03] - [[VW Golf VII (5G/AU) ABS Brakes | ABS Brakes]] ===<br />
* [[VW Golf VII (5G/AU) ABS Brakes#Basic_Setting|Basic Setting]]<br />
**''5Q0-907-379-IPB-V1.clb''<br />
**''EV_Brake1UDSContiMK100IPB_VW37''<br />
* G85 is calibrated in Address 44. See [https://forums.ross-tech.com/showthread.php?4224-MQB-(Mk7-Golf)-Steering-Angle-Sensor-(G85)-Calibration-in-44-Steering-Assist&p=144324&viewfull=1#post144324 this post]<br />
<br />
=== [05] - Access/Start Authorization ===<br />
<br />
=== [08] - Auto HVAC ===<br />
<br />
=== [09] - Cent. Elect. ===<br />
<br />
'''Note #1''': ''Before making ANY changes, you should run and Save a controller channel map of Adaptation in address 09. [[Control_Module_Maps]]<br><br />
'''Note #2''': ''Starting around model year 2018 many BCM/CECM modules show all zeros for Coding. In these applications, Coding is neither necessary nor possible. Instead changes are made using Adaptation as discussed here: https://forums.ross-tech.com/index.php?threads/10616/<br />
<br />
=== [15] - [[AirbagVW20 | Airbags]] ===<br />
<br />
=== [16] - Steering Wheel ===<br />
<br />
=== [17] - [[VW Golf VII (5G/AU) Instrument Cluster | Instrument Cluster]] ===<br />
<br />
* [[VW Golf VII (5G/AU) Instrument Cluster#Service_Reminder|Service Reminder]]<br />
<br />
=== [19] - [[VW Golf VII (5G/AU) CAN Gateway|CAN Gateway]] ===<br />
<br />
=== [2B] - Steering Column Lock ===<br />
<br />
=== [42] - Door Elect, Driver ===<br />
<br />
=== [44] - Steering Assist === <br />
<br />
=== [52] - Door Elect, Pass ===<br />
<br />
=== [55] - [[VW MQB Headlight Regulation|Headlight Aim Control]] ===<br />
* [[VW MQB Headlight Regulation#Coding|Coding]]<br />
* [[VW MQB Headlight Regulation#Coding|Basic Setting]]<br />
<br />
=== [5F] - Information Electronics ===<br />
<br />
=== [75] - Telematics ===<br />
<br />
=== [A9] - Struct. Borne Sound ===</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Main_Page&diff=8921
Main Page
2020-09-09T20:31:56Z
<p>Andy: </p>
<hr />
<div><center><u>'''Welcome to the Ross-Tech WIKI.'''</u><br><br><br />
<br />
''At the present time, this Wiki is experimental, and editable only by a small group.''<br><br />
''All content can be browsed '''WITHOUT''' an account. An account is only needed for those''<br><br />
''who wish to contribute on a regular basis! If you have a single contribution, please submit''<br><br />
''plain text to Support@Ross-Tech.com. If you submit contributions regularly using this method,''<br><br />
''we will likely contact you and offer to set up an account for you.''<br><br><br />
<br />
''Any links that are in RED are to pages that do not yet exist.''<br><br />
''There is thus no point in emailing Ross-Tech if you are trying to view that content.''<br></center><br />
<br />
<br />
<!-- TOC --><br />
<table align="center" width="80%" style="background:#eaeaea;"><br />
<caption style="color: #7d7d7d;text-align: center; font-size: 18px; font-weight: bold; padding-bottom: 6px;">Table of Contents</caption><br />
<tr> <br />
<td style="font-size: 14px;" width="25%" height="40px" align="center">'''[[Diagnostic Procedures]]'''</td> <br />
<td style="font-size: 14px;" width="25%" height="40px" align="center">'''General'''</td><br />
<td style="font-size: 14px;" width="25%" height="40px" align="center">'''Documentation'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7; border: none;font-size: 14px;" height="30px">[[Diagnostic Procedures#Audi|'''Audi''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7; border: none;font-size: 14px;" height="30px">[[:Category:Fault Codes|'''Fault Codes''']]</td><br />
<td width="25%" align="center" style="background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/main_screen.html '''VCDS Manual''']</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures#Seat|'''Seat''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Common Procedures]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Control Module Maps]]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures#Skoda|'''Skoda''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Retrofitting]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Common Acronyms]]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures#Volkswagen|'''Volkswagen''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Immobilizer]]'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Official Factory Repair Information]]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">[[Diagnostic Procedures|'''Others''']]</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''Component Protection'''</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[http://meta.wikipedia.org/wiki/MediaWiki_User%27s_Guide WIKI User's Guide]'''</td> <br />
</tr><br />
<tr> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Functions|Function Chart]] '''</td> <br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px"> [https://forums.ross-tech.com ''' Ross-Tech Forum ''']</td><br />
<td width="25%" align="center" style="background:#f7f7f7;font-size: 14px;" height="30px">'''[[Videos]]'''</td><br />
</tr><br />
</table><br />
<br />
<br><br />
<div style="text-align: center;"><br />
== How to use the Ross-Tech Wiki ==<br />
<br />
[[File:Wiki_video_thumb.png|400px|link=http://www.youtube.com/watch?v=8BIyIGV1_mw]]<br />
<br />
http://www.youtube.com/watch?v=8BIyIGV1_mw<br />
<br />
"''Give a man a fish and you'll have fed him for a day. Teach a man to fish and you can sell him fishing equipment''"<br />
</div></div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Battery_Replacement&diff=8865
Battery Replacement
2020-06-23T21:17:24Z
<p>Andy: /* Special Notes */</p>
<hr />
<div>__FORCETOC__<br />
<br />
A large majority of modern VW/Audi/Seat/Skoda vehicles require the configuration of replacement batteries. The diagnostic steps vary depending on the actual vehicle configuration.<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* New VW/Audi Battery Installed<br />
** Aftermarket batteries may NOT have a valid Part Number, Vendor code or Serial number. Ross-Tech cannot offer assistance if the necessary information is missing.<br />
* Key On, Engine OFF<br />
<br><br />
== 61-Battery Regulation using CAN ==<br />
This procedure applies to battery replacement in vehicles using a separate battery management control module.<br />
Address '''61: Battery Regul.''' Labels: 4F0-910-181.lbl<br />
Part No SW: 4F0 910 181 E HW: 4F0 915 181 A<br />
Component: ENERGIEMANAGER H12 0490 <br />
<br />
Subsystem 1 - Part No: 000 915 105 C<br />
Component: von VA0 2502160103 <br />
Coding: 303030393135313035432056413032353032313630313033<br />
Shop #: WSC 54332 321 22222<br />
=== Coding ===<br />
'''[Select]'''<br><br />
'''[61 - Battery Regulation]'''<br><br />
'''[Coding - 07]'''<br><br />
Use the pull down menu to select the battery (slave) listed as #1.<br><br />
'''[http://www.ross-tech.com/vcds/tour/recode_screen.html#battery [Battery Coding]]'''<br><br />
* Enter the new Battery Part Number (10 or 11 digits).<br />
* Enter the new Battery Serial Number (10 digits).<br />
* Select the new Battery Vendor.<br />
'''[OK]'''<br><br />
'''[Do it!]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
Your new Battery should now be coded and the Battery Control Module should be aware of the new Battery.<br><br />
<br />
=== Special Notes ===<br />
* Some vehicles like Audi R8 along with some rest-of-world models with Stop-Start, can have a 61 that is really a virtual module in the 19-CAN Gateway. In these cases, the new battery information is entered in 61-Battery Regulation then Adaptation Channel 004.<br />
<br />
----<br />
<br />
== 19-CAN Gateway using CAN ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address '''19: CAN Gateway (J533)''' Labels: 8T0-907-468.clb<br />
Part No SW: 8T0 907 468 Q HW: 8T0 907 468 L<br />
Component: GW-BEM 5CAN-M H10 0095 <br />
<br />
Subsystem 1 - Part No SW: 8K0 915 181 B HW: 8K0 915 181 B<br />
Component: '''J367-BDM''' H04 0150 <br />
=== Long Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long [Long Adaptation-0A]] function under 19-CAN-Gateway control module. Follow the on-screen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Long Adaptation-0A]'''<br><br />
Channel 004<br><br />
'''[Read]'''<br><br />
VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example:<br />
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ<br />
<br />
N = Battery Part Number (11 Digits)<br />
X = Battery Vendor (3 Digits)<br />
Z = Battery Serial Number (10 Digits)<br />
<br />
'''[Add to Log]''' ''Saving the original value to a log is strongly recommended''.<br><br />
Type the New Battery details into the '''New value''' field.<br><br />
* Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.<br />
'''[Test]''' <br><br />
'''[Save]'''<br><br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br />
=== Special Notes ===<br />
* Measuring Block groups 017, 018, 019 and 020 should show Battery information.<br />
* Registered users encountering difficulty can contact us via [mailto:Support@Ross-Tech.com email] -or- join and post in [http://forums.ross-tech.com our forum]. Please include the Auto-Scan, Saved Adaptation Channel 004 Log prior to modifications, the part number, serial number and vendor code located on the original battery and the details located on the brand new battery in addition to the error message details.<br />
<font color=white>tinyurl.com/pzgolq7</font><br />
<br />
----<br />
<br />
== 19-CAN Gateway using (UDS/ODX) ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address 19: '''CAN Gateway (J533)''' Labels: None<br />
Part No SW: 4G0 907 468 E HW: 4G0 907 468 A<br />
Component: J533--Gateway H08 0213 <br />
ASAM Dataset: EV_GatewUDS 001025<br />
<br />
'''Battery Monitoring Control Module''': <br />
Subsystem 1 - Part No SW: 8X0 915 181 HW: 8X0 915 181 <br />
Component: J367-BDM H07 0140 <br />
=== Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html [Adaptation-10]] function under 19-CAN-Gateway control module. Use the drop-down menus to enter the Part Number, Vendor, and Serial Number information located on the new battery .<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Adaptation - 10]'''<br><br />
* '''Battery adaptation - Size (this may be something like IDE03256-MAS04490 Battery adaptation - Size)'''<br />
** Select the battery Ah rating from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Manufacturer (this may be something like IDE03256-MAS03159 Battery adaptation - Manufacturer)'''<br />
** Select the battery manufacturer from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Serial number (this may be something like IDE03256-IDE00010 Battery adaptation - Serial number)'''<br />
** Type the serial number code from the replacement battery followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br><br />
<br />
----<br />
<br />
== Example Picture ==<br />
'''Note''': The 10 digit serial number may be preceded by the Battery Vendor Code, for instance VA0. See examples below: <br />
{| class="wikitable" border="0" width="450"<br />
|-<br />
!colspan="14" style="background:white"| Click on thumbnail image to enlarge.<br />
|-<br />
| [[File:Battery serial number.jpg|200px|center|caption]]<br />
|-<br />
| If the code is VA0310314E04G then drop the VA0 and just enter 310314E04G as the Serial Number.<br />
|}<br />
<br><br />
== Video Link ==<br />
[[File:Wikibatterycoding.jpg|200px|link=http://www.youtube.com/watch?v=IJAScg6JrYI]]<br />
<br />
http://www.youtube.com/watch?v=IJAScg6JrYI<br />
== Notes ==<br />
* Users encountering difficulty with the data shown on the battery sticker may want to:<br />
** Consider scanning the QR code with a smart phone app. We have had success with BB, Android and iOS platform mobile devices running [http://www.i-nigma.com/Downloadi-nigmaReader.html i-nigma's free app.]<br><br />
** Refer to this [http://www.audizine.com/forum/showthread.php/581232-B8-A4-Battery-Replacement-Coding B8 A4 Battery Replacement - Coding] thread which discusses labels in some detail.<br />
** We have seen some cases where (contrary to established norms) some Varta batteries have VAO (letter O) instead of VA0 (number 0). If you encounter a problem with Coding one of these, please try substituting the letter for the number or vice versa.<br />
<br />
[[Category:Subsystems]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Golf_VII_(5G/AU)&diff=8853
VW Golf VII (5G/AU)
2020-04-13T20:09:09Z
<p>Andy: </p>
<hr />
<div>This page will have information about the Golf 7.<br />
<br />
These pages have some information on tweaks for the Mk7 Golf platform vehicles:<br />
<br />
http://forums.ross-tech.com/showthread.php?512-MQB-Platform-tweaks<br />
<br />
http://www.golfgtiforum.co.uk/index.php?topic=260248.0<br />
<br />
http://vcds.greg-roberts.com/view-entries<br />
<br />
http://forums.vwvortex.com/showthread.php?7013354<br />
<br />
http://forums.vwvortex.com/showthread.php?7231270<br />
<br />
https://sites.google.com/a/naturalnetworks.ca/vw-golf-mk7-vcds-how-to/<br />
<br />
http://forums.vwvortex.com/showthread.php?8687226-VCDS-coding-on-an-Alltrack<br />
<br />
----<br />
<br />
<br />
<br />
{{Infobox-Model<br />
|Brand=Volkswagen<br />
|Model=Golf VII<br />
|Image=VW-Golf-VII.jpg<br />
|ImageSource=Ross-Tech, LLC<br />
|Manufacturer=Volkswagen AG<br />
|ChassisCode= 5G / AU<br />
|Platform=VW37X<br />
|from=2013<br />
|through=<br />
|fromUS=2015<br />
|throughUS=<br />
|Predecessor=[[VW Golf/Golf Plus (5K/52)]]<br />
|Successor=-<br />
|Interface='''All model years''' [http://www.ross-tech.com/vcds/interfaces.php HEX-V2], [http://www.ross-tech.com/vcds/interfaces.php HEX-NET]<br />
''Limited 2016+ RoW market coverage [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php HEX+CAN], [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php Micro-CAN]''<br />
|DLCImage=DLC-VWGolf5G.jpg<br />
|DLC=The DLC is located in the Driver Footwell.<br />
}}<br />
<br />
=== [01] - Engine ===<br />
<br />
=== [02] - [[6-Speed Direct Shift Gearbox (DSG/0D9) | Auto Trans]] ===<br />
<br />
=== [03] - [[VW Golf VII (5G/AU) ABS Brakes | ABS Brakes]] ===<br />
* [[VW Golf VII (5G/AU) ABS Brakes#Basic_Setting|Basic Setting]]<br />
**''5Q0-907-379-IPB-V1.clb''<br />
**''EV_Brake1UDSContiMK100IPB_VW37''<br />
* G85 is calibrated in Address 44. See [https://forums.ross-tech.com/showthread.php?4224-MQB-(Mk7-Golf)-Steering-Angle-Sensor-(G85)-Calibration-in-44-Steering-Assist&p=144324&viewfull=1#post144324 this post]<br />
<br />
=== [05] - Access/Start Authorization ===<br />
<br />
=== [08] - Auto HVAC ===<br />
<br />
=== [09] - Cent. Elect. ===<br />
<br />
'''Note #1''': ''Before making ANY changes, you should run and Save a controller channel map of Adaptation in address 09. [[Control_Module_Maps]]<br><br />
'''Note #2''': ''Starting around model year 2018 many BCM/CECM modules show all zeros for Coding. In these applications, Coding is neither necessary nor possible. Instead changes are made using Adaptation as discussed here: https://forums.ross-tech.com/showthread.php?10616-Modules-reporting-zero-code-string]<br />
<br />
=== [15] - [[AirbagVW20 | Airbags]] ===<br />
<br />
=== [16] - Steering Wheel ===<br />
<br />
=== [17] - [[VW Golf VII (5G/AU) Instrument Cluster | Instrument Cluster]] ===<br />
<br />
* [[VW Golf VII (5G/AU) Instrument Cluster#Service_Reminder|Service Reminder]]<br />
<br />
=== [19] - [[VW Golf VII (5G/AU) CAN Gateway|CAN Gateway]] ===<br />
<br />
=== [2B] - Steering Column Lock ===<br />
<br />
=== [42] - Door Elect, Driver ===<br />
<br />
=== [44] - Steering Assist === <br />
<br />
=== [52] - Door Elect, Pass ===<br />
<br />
=== [55] - [[VW MQB Headlight Regulation|Headlight Aim Control]] ===<br />
* [[VW MQB Headlight Regulation#Coding|Coding]]<br />
* [[VW MQB Headlight Regulation#Coding|Basic Setting]]<br />
<br />
=== [5F] - Information Electronics ===<br />
<br />
=== [75] - Telematics ===<br />
<br />
=== [A9] - Struct. Borne Sound ===</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Golf_VII_(5G/AU)_ABS_Brakes&diff=8832
VW Golf VII (5G/AU) ABS Brakes
2020-03-12T19:50:31Z
<p>Andy: /* Open Rear Parking Brake */</p>
<hr />
<div>== Basic Setting ==<br />
=== Caution! ===<br />
* Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors. <br />
* Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.<br />
* It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults! There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door.<br />
<br />
=== Open Rear Parking Brake ===<br />
'''<u>Prerequisites:</u>'''<br><br />
* Connect a battery charger as per repair manual. (For plug-ins like the e-Golf/Golf GTE/A3 e-tron/etc., connect the EV charging cable)<br />
* Cycle the Parking Brake ON, then OFF first.<br />
'''[Select]'''<br><br />
'''[03 - ABS Brakes]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Select '''Start lining change mode'''''<br><br />
'''[Go!]''' to activate the Basic Setting.<br><br />
The brake calipers will then open, allowing the pads to be changed.<br><br />
You should hear the rear caliper motors operating. <br><br />
Wait 30 seconds after it says '''Not Running''' or the noises have stopped before clicking '''[Stop]'''<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
* Turn ignition off and leave battery charger connected.<br><br />
<br />
''The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool. Fault code [[721152 | 721152 - Brake pad replacement mode active]] will be stored, this is normal.''<br />
<br />
=== Close Rear Parking Brake ===<br />
'''<u>Prerequisites:</u>'''<br><br />
* Connect a battery charger as per repair manual.<br />
'''[Select]'''<br><br />
'''[03 - ABS Brakes]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Select '''End lining change mode'''''<br><br />
'''[Go!]''' to activate the Basic Setting.<br><br />
The brake calipers will then close.<br><br />
Wait 30 seconds after it says '''Not Running''' or the noises have stopped before clicking '''[Stop]'''<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
* Turn ignition off<br><br />
<br />
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly in addition to Fault code [[C1011 | C1011 - Brake pad replacement mode active]]. This should stop after cycling the Parking Brake ON, then OFF again using the switch in the vehicle while holding the brake pedal AFTER all rear brake components are reassembled.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=02275&diff=8703
02275
2019-06-13T13:30:59Z
<p>Andy: Created page with "__FORCETOC__ == 02275 - Quiescent Current Stage 4 == ==== Special Notes ==== * A customer reported this fault was due to wrong battery and BEM configuration in a 2006 Audi S8..."</p>
<hr />
<div>__FORCETOC__<br />
== 02275 - Quiescent Current Stage 4 ==<br />
<br />
==== Special Notes ====<br />
* A customer reported this fault was due to wrong battery and BEM configuration in a 2006 Audi S8. <br />
<br />
<br />
<br />
__FORCETOC__<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=6-Speed_Direct_Shift_Gearbox_(DSG/02E)&diff=8682
6-Speed Direct Shift Gearbox (DSG/02E)
2019-05-07T12:52:41Z
<p>Andy: /* Basic Setting */</p>
<hr />
<div>__FORCETOC__<br />
<br />
'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Direct-Shift_Gearbox Wikipedia entry]. Additional information can be found in the [[Official Factory Repair Information]] and sources such as [http://www.bentleypublishers.com//volkswagen/technical-training/vw-02e-direct-shift-gearbox-ssp.html Bentley Publisher's VW SSP (Self-Study Program 851403)] and [http://www.bentleypublishers.com//audi/technical-training/audi-02e-direct-shift-gearbox-ssp.html Bentley Publisher's Audi SSP (Self-Study Program 951403)].<br><br />
<br><br />
<br />
== Coding ==<br />
<br />
* When replacing this Mechatronic unit, simply copy the coding from the original Auto-Scan and paste it into the New Coding section of the replacement followed by clicking '''[[http://www.ross-tech.com/vcds/tour/recode_screen.html Do it!]]'''. <br><br />
* If the original Coding is unknown, coding information can be found in the pop-up balloon within the VCDS '''[[http://www.ross-tech.com/vcds/tour/recode_screen.html Coding-07]]''' function.<br><br />
<br />
<br />
== Basic Setting ==<br />
'''<u>Prerequisites:</u>'''<br><br />
* Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. (Fluid Level needs to be correct!)<br />
* Selector Lever in P<br />
* Ignition ON<br />
* Engine ON (Idling) for one minute or more<br />
* Brake Pedal operated (hold for the whole procedure)<br />
* Throttle Pedal not operated<br />
* Cruise control is switched OFF<br><br />
<br />
'''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.''<br />
<br />
'''[Select]'''<br><br />
'''[02 - Transmission]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
<br />
=== Transmission Tolerances (Engaged Calibration) ===<br />
<br />
Group 061<br><br />
'''[Go!]'''<br><br />
* When you go to Basic Settings 061 and click GO the screen may look like this: [http://wiki.ross-tech.com/wiki/images/3/35/02-04-061_start.png Basic Settings 061]<br><br />
* Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://wiki.ross-tech.com/wiki/images/1/1e/02-04-061_end.png Basic Settings 061]<br><br />
<br />
Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.<br><br />
<br />
=== Transmission Tolerances (Synch. Point. Measurement) ===<br />
<br />
Group 060<br><br />
'''[Go!]'''<br><br />
* When you go to Basic Settings 060 and click GO the screen may look like this: [http://wiki.ross-tech.com/wiki/images/a/a8/02-04-060_start.png Basic Settings 060]<br><br />
* Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://wiki.ross-tech.com/wiki/images/3/3e/02-04-060_end.png Basic Settings 060]<br><br />
<br />
Wait until Basic Settings has switched to ON and all numbers have stopped moving.<br />
<br />
=== Clutch Adaptation ===<br />
<br />
'''''Control Module Software Version < 0800:'''''<br />
<br />
Group 062<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
<br />
Special notes.<br />
*When found in the early software level (0627/0628) (8N) Audi TT:<br />
** Basic Settings group 062 may take several minutes to complete. The final values may report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished.<br />
** If Basic Settings group 062 reports ''ERROR:| Group 062| Not | Available'' try test driving the vehicle and repeating at normal operating temp.<br />
''Internal Ref: ST?ID=66725 and E?ID=309867'' <br />
<br />
'''''Control Module Software Version >= 0800 :'''''<br />
<br />
Group 067<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
<br />
=== Reset Values (Clutch Safety Function) ===<br />
<br />
Group 068<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
<br />
=== Reset Values (Pressure Adaptation) ===<br />
<br />
Group 065<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
<br />
=== Reset Values (Steering Wheel Paddle Installation) ===<br />
<br />
Group 063<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
<br />
=== Reset Values (ESP & Tip Cruise Control Installation) ===<br />
<br />
Group 069<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
<br />
'''[Done, Go Back]'''<br><br />
Switch off Ignition, wait 10 Seconds and switch it back on.<br><br />
'''[Fault Codes - 02]'''<br><br />
Check and clear fault codes after successful test.<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
Perform the Defined Test Drive.<br><br><br />
<br />
== Special Procedures ==<br />
=== Defined Test Drive ===<br />
''Suggested test drive after replacing the mechatronic or successful basic setting.''<br><br><br />
'''<u>Prerequisites:</u>'''<br><br />
* Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.<br />
* Do Not use Cruise Control.<br />
<br />
Drive in Tiptronic Mode from stand still up to 6th Gear.<br><br />
While doing that make sure to drive in Gears 3 or 5 for approx. 5 minutes and also in 4 or 6 for approx. 5 minutes.<br><br />
The engine speed window for all gears is 1200 - 3500 RPM (for clutch calibration).<br><br />
Perform one sharp braking followed by a full throttle acceleration (oil return check) while in Drive, Not Tiptronic Mode.<br><br />
Evaluate creep and starting-off points.<br><br />
Check for leaks.<br><br />
<br />
'''''NOTE:''' If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.''<br />
<br />
==== Special Notes ====<br />
<br />
* Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own. <br />
<br />
* It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises.<br />
<br />
* Customers with TDI's have reported that an RPM range of 2000-2500 rpm is sufficient.<br />
<br />
<br />
----<br />
<br />
== Replacement == <br />
Replacement Mechatronic units should be ordered by VIN based on [[Production Codes (PR-Codes) can be found on the Vehicle Data Label | PR Codes]] to confirm vehicle compatibility.<br />
* Run and save a complete Auto-Scan and save it prior to Mechatronic unit removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br><br />
* Enter the original [[6-Speed Direct Shift Gearbox (DSG/02E)#Coding | Coding]] into the New Coding section of the replacement controller.<br />
* Complete [[6-Speed Direct Shift Gearbox (DSG/02E)#Basic Setting | Basic Settings]]<br />
* Complete the [[6-Speed Direct Shift Gearbox (DSG/02E)#Special Procedures | Defined Test Drive]]<br />
[[Category:Transmissions]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Audi_RCEPS_Steering_Assist&diff=8666
Audi RCEPS Steering Assist
2019-01-28T15:23:05Z
<p>Andy: /* Resetting of learned values for steering assistance */</p>
<hr />
<div>__FORCETOC__<br />
<br />
This page applies to the following vehicles with Audi RCEPS (J500) 44-Steering Assist:<br />
<br />
* [[Audi A4/S4/RS4/Cabriolet (8K) | A4/S4/RS4/Cabriolet (8K/FL)]]<br />
* [[Audi A5/S5 (8T) | A5/S5 (8T/FH/FR)]]<br />
* [[Audi Q5 (8R) | Audi Q5 (8R/FP)]]<br />
* [[Audi A6/S6/RS6/allroad (4G/FC)]]<br />
* [[Audi A7 (4G) | A7 (4G)]]<br />
* [[ Audi A8/S8 (4H) | A8/S8 (4H)]]<br />
The Steering Assist type can be identified by evaluating the data in the Auto-Scan: <br />
<br />
Address 44: Steering Assist (J500) Labels: 4G0-909-144.clb<br />
Part No SW: 4G0 909 144 K HW: 4G0 909 144 G<br />
Component: '''RCEPS''' H36 0009 <br />
ASAM Dataset: '''EV_RCEPS''' 007007<br />
<br />
Address 44: Steering Assist (J500) Labels: 8K0-909-144.clb<br />
Part No SW: 8K0 909 144 G HW: 8K0 909 144 B<br />
Component: '''RCEPS''' H40 0508 <br />
ASAM Dataset: '''EV_RCEPSAU48X''' 008015<br />
<br />
== Coding ==<br />
* Replacement control modules should be coded to the original configuration per the saved Auto-Scan.<br />
** If the original coding is rejected:<br />
*** NAR (North American Region) TPI 2027779 may apply<br />
*** See the parts catalog for any applicable parts bulletins<br />
* Coding may not be possible with the engine running.<br />
* Coding Information is available using the Long Coding Helper function in VCDS.<br />
* Registered users encountering difficulty can join and post the inquiry in our [http://forums.ross-tech.com/ forum] -or- contact us directly via [mailto:Support@Ross-Tech.com email] with the complete Auto-Scan and repair history.<br><br />
<br />
== Adaptation ==<br />
<br />
== Security Access ==<br />
* Will appear in a pop-up balloon when connected to this controller. <br />
<br />
== Basic Setting ==<br />
'''Prerequisites:'''<br><br />
* 03-ABS Brake control module DTCs for G85 No or Incorrect Basic Setting / Adaptation need to be resolved in the 16-Steering Wheel Electronics first! One of these pages would apply depending on the vehicle in question:<br />
** [[Audi A5 (8T) Steering Wheel Electronics]]<br />
** [[Audi A6 (4G) Steering Wheel Electronics]]<br />
*** If in doubt refer to the [[Diagnostic Procedures]] page to select the chassis type.<br />
<br />
=== Resetting of learned values for steering assistance ===<br />
This procedure would need to be performed if DTC C10AC ''Steering End Stops Not Learned'' was NOT resolved by following the G85 [[Audi RCEPS Steering Assist#Basic Setting | Basic Settings]] procedure step above in conjunction with:<br />
* Electromechanical Steering Rack replacement.<br />
* Mechanical repairs to the front involved significant alignment modifications to the vehicle.<br />
If DTC C10AC ''Steering End Stops Not Learned'' is stored due to low battery voltage -or- G85 replacement alone this procedure should '''NOT''' be necessary.<br />
<br />
'''Prerequisites:'''<br><br />
* New steering components installed and vehicle alignment completed.<br><br />
* No electrical faults stored in the 44-Steering Assist (J500) control module.<br><br />
* DTC C10AC Stored<br><br />
* Key On, Engine Off ''(KOEO)''<br><br />
<br />
'''[Select]'''<br><br />
'''[44 - Steering Assist]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter the code shown in the pop-up balloon to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Select '''Resetting of learned values for steering assistance''' from the drop-down menu<br><br />
'''[Go]'''<br><br />
When Finished Correctly ''or similar'' is shown click '''[Stop]'''<br><br />
*Note: VCDS may request a 1 to 3 digit code, if you receive this message, enter '''[000]''', then try again.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
Start the Engine ''(KOER)''<br><br />
* With the engine running turn the steering to full right lock and hold it for 5 to 10 seconds. The vehicle should produce an audible beep<br />
* Turn the steering to the complete left lock and the same audible beep should sound.<br />
* If the above 2 steps were not successful then try reversing the steps by turning first to the left and then to the right.<br />
* Straighten the wheels and wait 5 to 10 seconds while observing the steering and traction control warnings. They should extinguish although it is advised to scan the vehicle again for DTCs prior to the test drive.<br />
<br />
Note: It this procedure was not successful verify the alignment is within specifications. Although the difference between the right and left end stops needs to be less than 20°, the actual lock-to-lock G85 reading should be within 8° on a vehicle in proper working condition. A significant discrepancy due to collision repairs will prevent the steering limit end stops from learning.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=01498&diff=8621
01498
2018-10-30T12:33:05Z
<p>Andy: /* Special Notes */</p>
<hr />
<div>__FORCETOC__<br />
<br />
== 01498 - Bulb for Parking Lamps; Right (M3) ==<br />
=== 01498 - Bulb for Parking Lamps; Right (M3): Short to Ground ===<br />
=== 01498 - Bulb for Parking Lamps; Right (M3): Open or Short to Plus ===<br />
=== 01498 - Bulb for Parking Lamps; Right (M3): Open Circuit ===<br />
<br />
==== Possible Symptoms ====<br />
<br />
* M3 light does not illuminate<br />
<br />
==== Possible Causes ====<br />
<br />
* Blown fuse<br />
* Failed or incorrect turn signal bulb installed<br />
* Wiring harness issue<br />
<br />
==== Possible Solutions ====<br />
<br />
* Verify fuses are good<br />
* Verify correct light bulbs are installed<br />
* Test wiring harness, see factory repair manual<br />
<br />
==== Special Notes ====<br />
<br />
* When found on Touareg (7L):<br />
** If DTC [[00968]] is also stored, check fuses and wiring to J519 first.<br />
* When found in an Audi A8 D3 (4E):<br />
** A customer reports there are Sylvania 2827 Halogen bulbs (WY5W) inside the front headlights which are illuminated when the parking lights are on.<br />
<br />
<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=01494&diff=8620
01494
2018-10-30T12:32:32Z
<p>Andy: /* Special Notes */</p>
<hr />
<div><br />
__FORCETOC__<br />
<br />
== 01494 - Bulb for Parking Lamps; Left (M1) ==<br />
=== 01494 - Bulb for Parking Lamps; Left (M1): Short to Ground ===<br />
=== 01494 - Bulb for Parking Lamps; Left (M1): Open or Short to Plus ===<br />
=== 01494 - Bulb for Parking Lamps; Left (M1): Open Circuit ===<br />
<br />
==== Possible Symptoms ====<br />
<br />
* M1 light does not illuminate <br />
<br />
==== Possible Causes ====<br />
<br />
* Blown fuse<br />
* Failed or incorrect turn signal bulb installed<br />
* Wiring harness issue<br />
<br />
==== Possible Solutions ====<br />
<br />
* Verify fuses are good<br />
* Verify correct light bulbs are installed<br />
* Test wiring harness, see factory repair manual<br />
<br />
==== Special Notes ====<br />
<br />
* When found on Touareg (7L):<br />
** If DTC [[00967]] is also stored, check fuses and wiring to J519 first. <br />
* When found in an Audi A8 D3 (4E):<br />
** A customer reports there are Sylvania 2827 Halogen bulbs (WY5W) inside the front headlights which are illuminated when the parking lights are on. <br />
<br />
<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Cruise_Control_Retrofitting_(8X)&diff=8594
Cruise Control Retrofitting (8X)
2018-09-07T14:39:37Z
<p>Andy: </p>
<hr />
<div>== Requirements ==<br />
=== Official Retrofitting Kit ===<br />
<br />
The Official Retrofitting Kits are available through Audi directly but you can also source the Parts separately. Depending on the Options of the Car a different Kit has to be used.<br />
<br />
* Cars without Board Computer should use 8X0-054-690<br />
* Cars with Board Computer should use 8X0-054-690-A<br />
<br />
<br />
=== Steering Column Control Module ===<br />
<br />
There are different types of steering column control modules, the type is depending on several individual options so we have compiled [[VW Golf (1K) Steering Wheel Versions|a list of available part numbers]] for you. ''If a part number is not listed, registered VCDS users may [https://forums.ross-tech.com/forumdisplay.php?10-Retrofits post in our forum] to ask for help with this topic.''<br />
<br />
<br />
* [[Steering Wheel Control Module Versions|Steering Wheel Control Module Variants]]<br />
<br />
<br />
== Installation & Wiring ==<br />
<br />
Additional Information can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit.<br />
<br />
* Install proper Cruise Control Switch/Lever<br />
* Install proper Bottom Steering Column Cover, see Parts Catalog 953-50 Pos. 10 for Details.<br />
* If necessary Replace the Steering Column Control Module (J527), see Requirements above for Details.<br />
<br />
<br />
<br />
== Configuration ==<br />
<br />
* '''Update Steering Column Control Module (J527 / #16) Coding.'''<br />
** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be shown once you access the Coding Function using VCDS.''<br />
* '''Update the Engine Control Module (J623 / #01) Coding.'''<br />
** Make sure that the '''Engine is NOT running''', otherwise the new Coding will be rejected. Models equipped with Start/Stop System do have a Shutoff Switch/Button which will deactivate the Start/Stop Function.<br />
** As a Rule of Thumb, if the Engine Control Module uses a Short Coding the Activation is being done using Coding-II. If the Engine Control Module uses a Long Coding the Activation is done in (Long) Coding itself. Please also note that there are different Coding Variants for Long Coding.<br />
** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.''<br />
<br />
<br />
'''''If you are having trouble finding/calculating the proper Coding using the Long Coding Assist [https://forums.ross-tech.com/forumdisplay.php?10-Retrofits please post in our forum].''' Make sure to include a complete Diagnostic Protocol (Auto-Scan) from the Car and state which steps/work you have performed yet.''</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Battery_Replacement&diff=8592
Battery Replacement
2018-08-22T18:27:48Z
<p>Andy: /* Adaptation */</p>
<hr />
<div>__FORCETOC__<br />
<br />
A large majority of modern VW/Audi/Seat/Skoda vehicles require the configuration of replacement batteries. The diagnostic steps vary depending on the actual vehicle configuration.<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* New VW/Audi Battery Installed<br />
** Aftermarket batteries may NOT have a valid Part Number, Vendor code or Serial number. Ross-Tech cannot offer assistance if the necessary information is missing.<br />
* Key On, Engine OFF<br />
<br><br />
== 61-Battery Regulation using CAN ==<br />
This procedure applies to battery replacement in vehicles using a separate battery management control module.<br />
Address '''61: Battery Regul.''' Labels: 4F0-910-181.lbl<br />
Part No SW: 4F0 910 181 E HW: 4F0 915 181 A<br />
Component: ENERGIEMANAGER H12 0490 <br />
<br />
Subsystem 1 - Part No: 000 915 105 C<br />
Component: von VA0 2502160103 <br />
Coding: 303030393135313035432056413032353032313630313033<br />
Shop #: WSC 54332 321 22222<br />
=== Coding ===<br />
'''[Select]'''<br><br />
'''[61 - Battery Regulation]'''<br><br />
'''[Coding - 07]'''<br><br />
Use the pull down menu to select the battery (slave) listed as #1.<br><br />
'''[http://www.ross-tech.com/vcds/tour/recode_screen.html#battery [Battery Coding]]'''<br><br />
* Enter the new Battery Part Number (10 or 11 digits).<br />
* Enter the new Battery Serial Number (10 digits).<br />
* Select the new Battery Vendor.<br />
'''[OK]'''<br><br />
'''[Do it!]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
Your new Battery should now be coded and the Battery Control Module should be aware of the new Battery.<br><br />
<br />
=== Special Notes ===<br />
* Some vehicles like Audi R8 along with some rest-of-world models with Stop-Start, can have a 61 that is really a virtual module in the 19-CAN Gateway. In these cases, the new battery information is entered in 61-Battery Regulation then Adaptation Channel 004.<br />
<br />
----<br />
<br />
== 19-CAN Gateway using CAN ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address '''19: CAN Gateway (J533)''' Labels: 8T0-907-468.clb<br />
Part No SW: 8T0 907 468 Q HW: 8T0 907 468 L<br />
Component: GW-BEM 5CAN-M H10 0095 <br />
<br />
Subsystem 1 - Part No SW: 8K0 915 181 B HW: 8K0 915 181 B<br />
Component: '''J367-BDM''' H04 0150 <br />
=== Long Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long [Long Adaptation-0A]] function under 19-CAN-Gateway control module. Follow the on-screen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Long Adaptation-0A]'''<br><br />
Channel 004<br><br />
'''[Read]'''<br><br />
VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example:<br />
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ<br />
<br />
N = Battery Part Number (11 Digits)<br />
X = Battery Vendor (3 Digits)<br />
Z = Battery Serial Number (10 Digits)<br />
<br />
'''[Add to Log]''' ''Saving the original value to a log is strongly recommended''.<br><br />
Type the New Battery details into the '''New value''' field.<br><br />
* Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.<br />
'''[Test]''' <br><br />
'''[Save]'''<br><br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br />
=== Special Notes ===<br />
* Measuring Block groups 008, 019 and 020 should show Battery information.<br />
* Registered users encountering difficulty can contact us via [mailto:Support@Ross-Tech.com email] -or- join and post in [http://forums.ross-tech.com our forum]. Please include the Auto-Scan, Saved Adaptation Channel 004 Log prior to modifications, the part number, serial number and vendor code located on the original battery and the details located on the brand new battery in addition to the error message details.<br />
<font color=white>tinyurl.com/pzgolq7</font><br />
<br />
----<br />
<br />
== 19-CAN Gateway using (UDS/ODX) ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address 19: '''CAN Gateway (J533)''' Labels: None<br />
Part No SW: 4G0 907 468 E HW: 4G0 907 468 A<br />
Component: J533--Gateway H08 0213 <br />
ASAM Dataset: EV_GatewUDS 001025<br />
<br />
'''Battery Monitoring Control Module''': <br />
Subsystem 1 - Part No SW: 8X0 915 181 HW: 8X0 915 181 <br />
Component: J367-BDM H07 0140 <br />
=== Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html [Adaptation-10]] function under 19-CAN-Gateway control module. Use the drop-down menus to enter the Part Number, Vendor, and Serial Number information located on the new battery .<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Adaptation - 10]'''<br><br />
* '''Battery adaptation - Size (this may be something like IDE03256-MAS04490 Battery adaptation - Size)'''<br />
** Select the battery Ah rating from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Manufacturer (this may be something like IDE03256-MAS03159 Battery adaptation - Manufacturer)'''<br />
** Select the battery manufacturer from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Serial number (this may be something like IDE03256-IDE00010 Battery adaptation - Serial number)'''<br />
** Type the serial number code from the replacement battery followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br><br />
<br />
----<br />
<br />
== Example Picture ==<br />
'''Note''': The 10 digit serial number may be preceded by the Battery Vendor Code, for instance VA0. See examples below: <br />
{| class="wikitable" border="0" width="450"<br />
|-<br />
!colspan="14" style="background:white"| Click on thumbnail image to enlarge.<br />
|-<br />
| [[File:Battery serial number.jpg|200px|center|caption]]<br />
|-<br />
| If the code is VA0310314E04G then drop the VA0 and just enter 310314E04G as the Serial Number.<br />
|}<br />
<br><br />
== Video Link ==<br />
[[File:Wikibatterycoding.jpg|200px|link=http://www.youtube.com/watch?v=IJAScg6JrYI]]<br />
<br />
http://www.youtube.com/watch?v=IJAScg6JrYI<br />
== Notes ==<br />
* Users encountering difficulty with the data shown on the battery sticker may want to:<br />
** Consider scanning the QR code with a smart phone app. We have had success with BB, Android and iOS platform mobile devices running [http://www.i-nigma.com/Downloadi-nigmaReader.html i-nigma's free app.]<br><br />
** Refer to this [http://www.audizine.com/forum/showthread.php/581232-B8-A4-Battery-Replacement-Coding B8 A4 Battery Replacement - Coding] thread which discusses labels in some detail.<br />
** We have seen some cases where (contrary to established norms) some Varta batteries have VAO (letter O) instead of VA0 (number 0). If you encounter a problem with Coding one of these, please try substituting the letter for the number or vice versa.<br />
<br />
[[Category:Subsystems]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Battery_Replacement&diff=8591
Battery Replacement
2018-08-22T18:25:21Z
<p>Andy: /* Adaptation */</p>
<hr />
<div>__FORCETOC__<br />
<br />
A large majority of modern VW/Audi/Seat/Skoda vehicles require the configuration of replacement batteries. The diagnostic steps vary depending on the actual vehicle configuration.<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* New VW/Audi Battery Installed<br />
** Aftermarket batteries may NOT have a valid Part Number, Vendor code or Serial number. Ross-Tech cannot offer assistance if the necessary information is missing.<br />
* Key On, Engine OFF<br />
<br><br />
== 61-Battery Regulation using CAN ==<br />
This procedure applies to battery replacement in vehicles using a separate battery management control module.<br />
Address '''61: Battery Regul.''' Labels: 4F0-910-181.lbl<br />
Part No SW: 4F0 910 181 E HW: 4F0 915 181 A<br />
Component: ENERGIEMANAGER H12 0490 <br />
<br />
Subsystem 1 - Part No: 000 915 105 C<br />
Component: von VA0 2502160103 <br />
Coding: 303030393135313035432056413032353032313630313033<br />
Shop #: WSC 54332 321 22222<br />
=== Coding ===<br />
'''[Select]'''<br><br />
'''[61 - Battery Regulation]'''<br><br />
'''[Coding - 07]'''<br><br />
Use the pull down menu to select the battery (slave) listed as #1.<br><br />
'''[http://www.ross-tech.com/vcds/tour/recode_screen.html#battery [Battery Coding]]'''<br><br />
* Enter the new Battery Part Number (10 or 11 digits).<br />
* Enter the new Battery Serial Number (10 digits).<br />
* Select the new Battery Vendor.<br />
'''[OK]'''<br><br />
'''[Do it!]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
Your new Battery should now be coded and the Battery Control Module should be aware of the new Battery.<br><br />
<br />
=== Special Notes ===<br />
* Some vehicles like Audi R8 along with some rest-of-world models with Stop-Start, can have a 61 that is really a virtual module in the 19-CAN Gateway. In these cases, the new battery information is entered in 61-Battery Regulation then Adaptation Channel 004.<br />
<br />
----<br />
<br />
== 19-CAN Gateway using CAN ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address '''19: CAN Gateway (J533)''' Labels: 8T0-907-468.clb<br />
Part No SW: 8T0 907 468 Q HW: 8T0 907 468 L<br />
Component: GW-BEM 5CAN-M H10 0095 <br />
<br />
Subsystem 1 - Part No SW: 8K0 915 181 B HW: 8K0 915 181 B<br />
Component: '''J367-BDM''' H04 0150 <br />
=== Long Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long [Long Adaptation-0A]] function under 19-CAN-Gateway control module. Follow the on-screen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Long Adaptation-0A]'''<br><br />
Channel 004<br><br />
'''[Read]'''<br><br />
VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example:<br />
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ<br />
<br />
N = Battery Part Number (11 Digits)<br />
X = Battery Vendor (3 Digits)<br />
Z = Battery Serial Number (10 Digits)<br />
<br />
'''[Add to Log]''' ''Saving the original value to a log is strongly recommended''.<br><br />
Type the New Battery details into the '''New value''' field.<br><br />
* Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.<br />
'''[Test]''' <br><br />
'''[Save]'''<br><br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br />
=== Special Notes ===<br />
* Measuring Block groups 008, 019 and 020 should show Battery information.<br />
* Registered users encountering difficulty can contact us via [mailto:Support@Ross-Tech.com email] -or- join and post in [http://forums.ross-tech.com our forum]. Please include the Auto-Scan, Saved Adaptation Channel 004 Log prior to modifications, the part number, serial number and vendor code located on the original battery and the details located on the brand new battery in addition to the error message details.<br />
<font color=white>tinyurl.com/pzgolq7</font><br />
<br />
----<br />
<br />
== 19-CAN Gateway using (UDS/ODX) ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address 19: '''CAN Gateway (J533)''' Labels: None<br />
Part No SW: 4G0 907 468 E HW: 4G0 907 468 A<br />
Component: J533--Gateway H08 0213 <br />
ASAM Dataset: EV_GatewUDS 001025<br />
<br />
'''Battery Monitoring Control Module''': <br />
Subsystem 1 - Part No SW: 8X0 915 181 HW: 8X0 915 181 <br />
Component: J367-BDM H07 0140 <br />
=== Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html [Adaptation-10]] function under 19-CAN-Gateway control module. Use the drop-down menus to enter the Part Number, Vendor, and Serial Number information located on the new battery .<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Adaptation - 10]'''<br><br />
* '''Battery adaptation - Size'''<br />
** Select the battery Ah rating from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Manufacturer'''<br />
** Select the battery manufacturer from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Serial number'''<br />
** Type the serial number code from the replacement battery followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br><br />
<br />
----<br />
<br />
== Example Picture ==<br />
'''Note''': The 10 digit serial number may be preceded by the Battery Vendor Code, for instance VA0. See examples below: <br />
{| class="wikitable" border="0" width="450"<br />
|-<br />
!colspan="14" style="background:white"| Click on thumbnail image to enlarge.<br />
|-<br />
| [[File:Battery serial number.jpg|200px|center|caption]]<br />
|-<br />
| If the code is VA0310314E04G then drop the VA0 and just enter 310314E04G as the Serial Number.<br />
|}<br />
<br><br />
== Video Link ==<br />
[[File:Wikibatterycoding.jpg|200px|link=http://www.youtube.com/watch?v=IJAScg6JrYI]]<br />
<br />
http://www.youtube.com/watch?v=IJAScg6JrYI<br />
== Notes ==<br />
* Users encountering difficulty with the data shown on the battery sticker may want to:<br />
** Consider scanning the QR code with a smart phone app. We have had success with BB, Android and iOS platform mobile devices running [http://www.i-nigma.com/Downloadi-nigmaReader.html i-nigma's free app.]<br><br />
** Refer to this [http://www.audizine.com/forum/showthread.php/581232-B8-A4-Battery-Replacement-Coding B8 A4 Battery Replacement - Coding] thread which discusses labels in some detail.<br />
** We have seen some cases where (contrary to established norms) some Varta batteries have VAO (letter O) instead of VA0 (number 0). If you encounter a problem with Coding one of these, please try substituting the letter for the number or vice versa.<br />
<br />
[[Category:Subsystems]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Tiguan_(5N)_Brake_Electronics&diff=8575
VW Tiguan (5N) Brake Electronics
2018-07-05T13:33:14Z
<p>Andy: /* Tire Pressure Monitoring System Reset */</p>
<hr />
<div>== Coding ==<br />
<br />
'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module. In case this is not possible please [http://www.ross-tech.com/contact.html contact us directly] and we will assist you with the Coding Process.<br />
<br />
''Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure the Auto-Scan includes the complete VIN of the vehicle in question.''<br> <br> <br> <br />
<br />
== Security Access ==<br />
<br />
* 40168 = Basic Setting Enabling<br />
* 50403 = Adaptation Enabling<br />
<br />
<br />
== Adaptation ==<br />
<br />
=== Channel 021: Overboost Level ===<br />
<br />
Select the Engine Type (Base Engine) using the Data Sticker/Production Codes.<br />
<br />
* 4 = PR-D16, D2T, D2Z, D33, D42, D4X, D4K, MW6, M0R, T72<br />
* 7 = PR-D0J, D0M, D2L, D34, D38, D3B, D3W, D3X, D47, D67, D6F, D6G, D7N, D91, D92, D93, D94, D96, DA1, DA4, DA5, MS9, M92<br />
<br />
=== Channel 061: Hydraulic Brake Reinforcement ===<br />
<br />
Select the Engine Type (Base Engine) using the Data Sticker/Production Codes.<br />
<br />
* 0 = PR-D3W, D3X, D7N, DA4, DA5, D0J, DA1, D0M, T72, D67, D2T, D2Z, D2L, D6F, D4K, D4X, D33, D34, D38, D42, D47, D67, D91, D92, D93, D94, D96, MS9, MW6, M92, D6G, D3B<br />
* 1 = PR-D4X (with G1A/G1C), D33 (with G1A/G1C), T72 (with G1A/G1C), D2T (with G1A/G1C), D2Z (with G1A/G1C), D67 (with U5E), M92 (with U5E), D2L (with U5C/U5D/U5E ''AND'' K8D), D3B (with 1LJ/1ZD/1ZG/1LH), D91 (with U5C/U5D/U5E ''AND'' K8D), D92 (with U5C/U5D/U5E ''AND'' K8D), D94 (with U5C/U5D/U5E ''AND'' K8D), D3X (with U5C/U5D/U5E ''AND'' K8D), D7N (with U5C/U5D/U5E ''AND'' K8D), D4K (with G1A/G1C), MW6 (with G1A/G1C), D42 (with G1A/G1C)<br />
Special note; Some NAR (North American Region) and Japanese market vehicles use a special value of 2 in this channel. Registered users can contact us directly via email as needed if DTC 03366 - Vacuum Sensor is stored.<br />
''Internal Ref: FS#899 and ST?ID=72027''<br />
<br />
== Basic Setting ==<br />
<br />
=== Sensor for Steering Angle (G85) ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* Start the vehicle.<br />
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.<br />
* While driving turn the steering wheel one turn to the right and one turn to the left.<br />
* When having the steering wheel straight again stop the vehicle with the wheels pointed straight.<br />
* Ensure that the steering wheel is not moved again.<br />
* Keep the engine running and do not switch off the ignition.<br />
* System voltage at least 12.0 V.<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter 40168, to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 060<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
After a successful basic setting, one of the fields should say "OK".<br><br />
'''[Done, Go Back]'''<br><br />
To make sure the basic setting was successful, check the sensor again.<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 004<br><br />
'''[Go!]'''<br><br />
Check field 1, the value has to be between -1.5 and +1.5 °.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
'''''Note:''' After successful basic setting, the [[VW_Passat_(3C)_Steering_Assist#Steering_Limit_Stop_Adaptation|Steering Limit Stop]] needs to be adapted too.''<br><br><br><br />
<br />
----<br />
<br />
=== Lateral/Longitudinal Acceleration & Yaw Rate Sensor (G200/G202/G251) ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* System voltage at least 12.0 V.<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 004<br><br />
'''[Go!]'''<br><br />
Check field 2, 3 and 4 - their value has to be between -1.5 and +1.5 m/s² or °/s.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter 40168, to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 061<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
After a successful basic setting, field 2 should say "OK".<br><br />
'''[Done, Go Back]'''<br><br />
To make sure the basic setting was succesful, check the sensor again.<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 004<br><br />
'''[Go!]'''<br><br />
Check field 2, 3 and 4 - their value has to be between -1.5 and +1.5 m/s² or °/s.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br><br><br />
<br />
----<br />
=== Brake Pressure Sensor 1 (G201) ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* System voltage at least 12.0 V.<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 005<br><br />
'''[Go!]'''<br><br />
Check field 1, the value has to be between -8.0 and +8.0 bar.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter 40168, to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 066<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
After a successful basic setting, field 3 should say "OK".<br><br />
'''[Done, Go Back]'''<br><br />
To make sure the basic setting was succesful, check the sensor again.<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 005<br><br />
'''[Go!]'''<br><br />
Check field 1, the value has to be between -3.8 and +3.8 bar.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br><br><br />
<br />
== Special Procedures ==<br />
<br />
=== System Function Test ===<br />
<br />
See [[ESP System Function Test (Bosch)|System Function Test]]<br />
<br />
<br />
=== Tire Pressure Monitoring System Reset ===<br />
<br />
This applies only to INDIRECT TPMS with rubber valve stems and no sensors in the wheels. Direct TPMS with metal valve stems and sensors can be accessed in the 65-TPMS module.<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* Ignition ON<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 042<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br><br />
* The Tire Pressure Monitoring Lamp (K220) should blink.<br />
* Now check the Tire Pressure and correct it if necessary.<br />
* Press and Hold the Tire Pressure Monitoring Button (E492) '''AND''' the ABS/ESP Button (E256) for 2 Seconds.<br />
* A short Tone should sound after pressing/holding these buttons for 2 Seconds and the blinking should change to a permanent lit Tire Pressure Monitoring Lamp (K220).<br />
* The Reset is now done and as soon as you let the buttons go the Tire Pressure Monitoring Lamp (K220) should go OFF.<br />
<br />
== Replacement ==<br />
<br />
After Replacing this Control Module these Steps have to be performed in the following Order:<br />
<br />
* [[#Coding|Code Brake Electronics (J104) Control Module]]<br />
* [[#Sensor for Steering Angle (G85)|Basic Setting for Steering Angle Sensor (G85)]]<br />
* [[#Lateral/Longitudinal Acceleration & Yaw Rate Sensor (G200/G202/G251)|Basic Setting for Lateral/Longitudinal Acceleration & Yaw Rate Sensor (G200/G202/G251)]]<br />
* [[#Brake Pressure Sensor 1 (G201)|Basic Setting for Brake Pressure Sensor 1 (G201)]]<br />
* [[#Channel 021: Overboost Level|Adaptation for Overboost Level]]<br />
* [[#Channel 061: Hydraulic Brake Reinforcement|Adaptation for Hydraulic Brake Reinforcement]]<br />
* Code Parking Brake Electronics (J540) Control Module<br />
** ''Generation III'' '''5N0-907-801''' series controllers:<br />
*** [[VW Tiguan (5N) Parking Brake#Coding|Code Parking Brake Electronics (J540) Control Module]]<br />
** ''Generation IV'' '''3AA-907-801''' series controllers:<br />
*** [[VW Sharan (7N) Parking Brake#Coding|Code Parking Brake Electronics (J540) Control Module]]<br />
* Perform Parking Brake Function Test<br />
** ''Generation III'' '''5N0-907-801''' series controllers:<br />
*** [[VW Tiguan (5N) Parking Brake#Function Test|Perform Parking Brake Function Test]]<br />
** ''Generation IV'' '''3AA-907-801''' series controllers:<br />
*** [[VW Sharan (7N) Parking Brake#Function Test|Perform Parking Brake Function Test]]<br />
''In case you are having trouble with procedure please [http://www.ross-tech.com/contact.html contact us directly] and we will assist you with the Coding Process. Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure the Auto-Scan includes the complete VIN of the vehicle in question.''<br />
<br />
__FORCETOC__</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Tiguan_(5N)_Brake_Electronics&diff=8574
VW Tiguan (5N) Brake Electronics
2018-07-05T13:31:54Z
<p>Andy: /* Special Procedures */</p>
<hr />
<div>== Coding ==<br />
<br />
'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module. In case this is not possible please [http://www.ross-tech.com/contact.html contact us directly] and we will assist you with the Coding Process.<br />
<br />
''Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure the Auto-Scan includes the complete VIN of the vehicle in question.''<br> <br> <br> <br />
<br />
== Security Access ==<br />
<br />
* 40168 = Basic Setting Enabling<br />
* 50403 = Adaptation Enabling<br />
<br />
<br />
== Adaptation ==<br />
<br />
=== Channel 021: Overboost Level ===<br />
<br />
Select the Engine Type (Base Engine) using the Data Sticker/Production Codes.<br />
<br />
* 4 = PR-D16, D2T, D2Z, D33, D42, D4X, D4K, MW6, M0R, T72<br />
* 7 = PR-D0J, D0M, D2L, D34, D38, D3B, D3W, D3X, D47, D67, D6F, D6G, D7N, D91, D92, D93, D94, D96, DA1, DA4, DA5, MS9, M92<br />
<br />
=== Channel 061: Hydraulic Brake Reinforcement ===<br />
<br />
Select the Engine Type (Base Engine) using the Data Sticker/Production Codes.<br />
<br />
* 0 = PR-D3W, D3X, D7N, DA4, DA5, D0J, DA1, D0M, T72, D67, D2T, D2Z, D2L, D6F, D4K, D4X, D33, D34, D38, D42, D47, D67, D91, D92, D93, D94, D96, MS9, MW6, M92, D6G, D3B<br />
* 1 = PR-D4X (with G1A/G1C), D33 (with G1A/G1C), T72 (with G1A/G1C), D2T (with G1A/G1C), D2Z (with G1A/G1C), D67 (with U5E), M92 (with U5E), D2L (with U5C/U5D/U5E ''AND'' K8D), D3B (with 1LJ/1ZD/1ZG/1LH), D91 (with U5C/U5D/U5E ''AND'' K8D), D92 (with U5C/U5D/U5E ''AND'' K8D), D94 (with U5C/U5D/U5E ''AND'' K8D), D3X (with U5C/U5D/U5E ''AND'' K8D), D7N (with U5C/U5D/U5E ''AND'' K8D), D4K (with G1A/G1C), MW6 (with G1A/G1C), D42 (with G1A/G1C)<br />
Special note; Some NAR (North American Region) and Japanese market vehicles use a special value of 2 in this channel. Registered users can contact us directly via email as needed if DTC 03366 - Vacuum Sensor is stored.<br />
''Internal Ref: FS#899 and ST?ID=72027''<br />
<br />
== Basic Setting ==<br />
<br />
=== Sensor for Steering Angle (G85) ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* Start the vehicle.<br />
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.<br />
* While driving turn the steering wheel one turn to the right and one turn to the left.<br />
* When having the steering wheel straight again stop the vehicle with the wheels pointed straight.<br />
* Ensure that the steering wheel is not moved again.<br />
* Keep the engine running and do not switch off the ignition.<br />
* System voltage at least 12.0 V.<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter 40168, to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 060<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
After a successful basic setting, one of the fields should say "OK".<br><br />
'''[Done, Go Back]'''<br><br />
To make sure the basic setting was successful, check the sensor again.<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 004<br><br />
'''[Go!]'''<br><br />
Check field 1, the value has to be between -1.5 and +1.5 °.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
'''''Note:''' After successful basic setting, the [[VW_Passat_(3C)_Steering_Assist#Steering_Limit_Stop_Adaptation|Steering Limit Stop]] needs to be adapted too.''<br><br><br><br />
<br />
----<br />
<br />
=== Lateral/Longitudinal Acceleration & Yaw Rate Sensor (G200/G202/G251) ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* System voltage at least 12.0 V.<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 004<br><br />
'''[Go!]'''<br><br />
Check field 2, 3 and 4 - their value has to be between -1.5 and +1.5 m/s² or °/s.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter 40168, to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 061<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
After a successful basic setting, field 2 should say "OK".<br><br />
'''[Done, Go Back]'''<br><br />
To make sure the basic setting was succesful, check the sensor again.<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 004<br><br />
'''[Go!]'''<br><br />
Check field 2, 3 and 4 - their value has to be between -1.5 and +1.5 m/s² or °/s.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br><br><br />
<br />
----<br />
=== Brake Pressure Sensor 1 (G201) ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* System voltage at least 12.0 V.<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 005<br><br />
'''[Go!]'''<br><br />
Check field 1, the value has to be between -8.0 and +8.0 bar.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Security Access - 16]'''<br><br />
Enter 40168, to enable the basic setting.<br><br />
'''[Do it!]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 066<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
After a successful basic setting, field 3 should say "OK".<br><br />
'''[Done, Go Back]'''<br><br />
To make sure the basic setting was succesful, check the sensor again.<br><br />
'''[Measuring Blocks - 08]'''<br><br />
Group 005<br><br />
'''[Go!]'''<br><br />
Check field 1, the value has to be between -3.8 and +3.8 bar.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br><br><br />
<br />
== Special Procedures ==<br />
<br />
=== System Function Test ===<br />
<br />
See [[ESP System Function Test (Bosch)|System Function Test]]<br />
<br />
<br />
=== Tire Pressure Monitoring System Reset ===<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* Ignition ON<br><br><br />
<br />
'''[Select]'''<br><br />
'''[03 - Brake Electronics]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Group 042<br><br />
'''[Go!]'''<br><br />
Activate the Basic Setting.<br><br />
'''[ON/OFF/Next]'''<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br><br />
* The Tire Pressure Monitoring Lamp (K220) should blink.<br />
* Now check the Tire Pressure and correct it if necessary.<br />
* Press and Hold the Tire Pressure Monitoring Button (E492) '''AND''' the ABS/ESP Button (E256) for 2 Seconds.<br />
* A short Tone should sound after pressing/holding these buttons for 2 Seconds and the blinking should change to a permanent lit Tire Pressure Monitoring Lamp (K220).<br />
* The Reset is now done and as soon as you let the buttons go the Tire Pressure Monitoring Lamp (K220) should go OFF.<br />
<br />
== Replacement ==<br />
<br />
After Replacing this Control Module these Steps have to be performed in the following Order:<br />
<br />
* [[#Coding|Code Brake Electronics (J104) Control Module]]<br />
* [[#Sensor for Steering Angle (G85)|Basic Setting for Steering Angle Sensor (G85)]]<br />
* [[#Lateral/Longitudinal Acceleration & Yaw Rate Sensor (G200/G202/G251)|Basic Setting for Lateral/Longitudinal Acceleration & Yaw Rate Sensor (G200/G202/G251)]]<br />
* [[#Brake Pressure Sensor 1 (G201)|Basic Setting for Brake Pressure Sensor 1 (G201)]]<br />
* [[#Channel 021: Overboost Level|Adaptation for Overboost Level]]<br />
* [[#Channel 061: Hydraulic Brake Reinforcement|Adaptation for Hydraulic Brake Reinforcement]]<br />
* Code Parking Brake Electronics (J540) Control Module<br />
** ''Generation III'' '''5N0-907-801''' series controllers:<br />
*** [[VW Tiguan (5N) Parking Brake#Coding|Code Parking Brake Electronics (J540) Control Module]]<br />
** ''Generation IV'' '''3AA-907-801''' series controllers:<br />
*** [[VW Sharan (7N) Parking Brake#Coding|Code Parking Brake Electronics (J540) Control Module]]<br />
* Perform Parking Brake Function Test<br />
** ''Generation III'' '''5N0-907-801''' series controllers:<br />
*** [[VW Tiguan (5N) Parking Brake#Function Test|Perform Parking Brake Function Test]]<br />
** ''Generation IV'' '''3AA-907-801''' series controllers:<br />
*** [[VW Sharan (7N) Parking Brake#Function Test|Perform Parking Brake Function Test]]<br />
''In case you are having trouble with procedure please [http://www.ross-tech.com/contact.html contact us directly] and we will assist you with the Coding Process. Every inquiry on this topic has to include a full Auto-Scan as well as which parts have been replaced and why, also make sure the Auto-Scan includes the complete VIN of the vehicle in question.''<br />
<br />
__FORCETOC__</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=01134&diff=8565
01134
2018-06-13T12:38:39Z
<p>Andy: </p>
<hr />
<div>__FORCETOC__<br />
== 01134 - Alarm Horn (H12) ==<br />
<br />
=== 01134 - Alarm Horn (H12): No Signal/Communication ===<br />
<br />
==== Possible Symptoms ====<br />
<br />
* Anti-Theft Alarm sporadically triggered<br />
<br />
==== Possible Causes ====<br />
<br />
* Fuse(s) faulty<br />
* Wiring and/or Connector(s) from/to Alarm Horn (H12) faulty<br />
* Alarm Horn (H12) faulty <br />
<br />
==== Possible Solutions ====<br />
<br />
* Check Fuse(s)<br />
* Check Wiring and/or Connector(s) from/to Alarm Horn (H12)<br />
* Check/Replace Alarm Horn (H12)<br />
<br />
==== Special Notes ====<br />
<br />
Some forum users have discovered a battery on the alarm horn that can fail over time and cause this fault as discussed here:<br />
<br />
http://www.ttforum.co.uk/forum/viewtopic.php?f=19&t=1834061<br />
<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Audi_R8_(42)&diff=8553
Audi R8 (42)
2018-05-10T14:41:37Z
<p>Andy: </p>
<hr />
<div>{{Infobox-Model<br />
|Brand=Audi<br />
|Model=R8 (42)<br />
|Image=Audi-R842.jpg<br />
|ImageSource=Thomas Doerfer[[Image:Wikipedia.gif|16px|link=http://en.wikipedia.org/wiki/File:Audi_R8_4.2_Jetblau.JPG]]<br />
|Manufacturer=quattro GmbH (Audi AG)<br />
|ChassisCode=42 / FG<br />
|Platform=AU714<br />
|from=2008<br />
|through=<br />
|fromUS=-<br />
|throughUS=-<br />
|Interface=[http://www.ross-tech.com/vcds/interfaces.php HEX-V2], [http://www.ross-tech.com/vcds/interfaces.php HEX-NET], [http://www.ross-tech.com/vag-com/old-interfaces/discontinued_interfaces.php HEX+CAN]<br />
|DLCImage=DLC-AudiR842.jpg<br />
|DLC=The DLC is located in the Driver Footwell<br>near the Pedals behind a Cover.<br />
}}<br />
'''General Information''' about this Model can be found in the [http://en.wikipedia.org/wiki/Audi_R8_(road_car) Wikipedia entry].<br />
<br />
=== [01] - [[:Category:Engines|Engine Electronics]] ===<br />
==== [[:Category:Gasoline Engines|Gasoline Engines]] ====<br />
* 4.2l V8 (BYH):<br />
** Coding<br />
** Adaptation<br />
** Basic Setting<br />
** Label File ''(079-910-560-BYH.CLB)''<br />
* 5.0l V10 FSI (BUJ):<br />
** Coding<br />
** Adaptation<br />
** Basic Setting<br />
** Label File ''(07L-910-552-BUJ.CLB)''<br />
<br />
=== [02] - [[:Category:Transmissions|Transmission]] ===<br />
=== [03] - [[Audi R8 (42) Brake Electronics|Brake Electronics]] ===<br />
* [[Audi R8 (42) Brake Electronics#Coding|Coding]]<br />
* [[Audi R8 (42) Brake Electronics#Basic Setting|Basic Setting]]<br />
* Label File ''(420-910-517.LBL)''<br />
<br />
=== [08] - Heating/Air Conditioning ===<br />
<br />
* [[Audi R8 (42) Heating/Air Conditioning#Coding|Coding]]<br />
* [[Audi R8 (42) Heating/Air Conditioning#Adaptation|Adaptation]]<br />
* [[Audi R8 (42) Heating/Air Conditioning#Basic Setting|Basic Setting]]<br />
* Label File<br />
<br />
=== [09] - Central Electronics / Body Control Module (BCM) ===<br />
<br />
* [[Audi R8 (42) Central Electronics|Central Electronics (< MY 2009)]]<br />
** [[Audi R8 (42) Central Electronics#Coding|Coding]]<br />
** [[Audi R8 (42) Central Electronics#Adaptation|Adaptation]]<br />
** Label File<br />
* [[Audi A3 (8P) Body Control Module|Body Control Module (MY 2010+)]]<br />
** ''As of MY 2010+ the Body Control Module (BCM) incorporates Central Electronics and Comfort System Functionality.<br>Make sure to have all Doors unlocked, otherwise this Control Module will block Communication with the Scan Tool/VCDS.''<br />
** [[Audi A3 (8P) Body Control Module#Coding|Coding]]<br />
** [[Audi A3 (8P) Body Control Module#Adaptation|Adaptation]]<br />
** [[Audi A3 (8P) Body Control Module#Replacement|Replacement]]<br />
** Label File ''(8P0-907-063.CLB)''<br />
<br />
=== [0F] - Radio (Digital) ===<br />
<br />
* Sirius<br />
** Label File ''(8E0-035-593-SIR.LBL)''<br />
* XM<br />
** Label File ''(8E0-035-593-XM.LBL)''<br />
<br />
=== [10] - [[Audi R8 (42) Parking Aid 2|Parking Aid 2]] ===<br />
<br />
''Through MY 2009 see '''[76] - Parking Aid'''.''<br />
<br />
* [[Audi R8 (42) Parking Aid 2|Coding]]<br />
* [[Audi R8 (42) Parking Aid 2|Adaptation]]<br />
* Label File ''(420-919-475.CLB)''<br />
<br />
=== [11] - Engine Electronics 2 ===<br />
<br />
''See Engine Electronics for Details.''<br />
<br />
=== [14] - Suspension Electronics ===<br />
<br />
=== [15] - [[Audi R8 (42) Airbag|Airbag]] ===<br />
<br />
* [[Audi R8 (42) Airbag#Coding|Coding]]<br />
* [[Audi R8 (42) Airbag#Adaptation|Adaptation]]<br />
* Label File ''(420-959-655.LBL)''<br />
<br />
=== [16] - [[Audi R8 (42) Steering Wheel|Steering Wheel]] ===<br />
<br />
* [[Audi R8 (42) Steering Wheel#Coding|Coding]]<br />
* [http://www.ross-tech.com/vag-com/download/label-files/1K0-953-549.lbl Label File]<br />
<br />
=== [17] - [[Audi R8 (42) Instrument Cluster|Instrument Cluster]] ===<br />
<br />
* [[Audi R8 (42) Instrument Cluster#Coding|Coding]]<br />
* [[Audi R8 (42) Instrument Cluster#Adaptation|Adaptation]]<br />
* Label File<br />
<br />
=== [19] - [[VW Golf (1K) CAN-Gateway|CAN-Gateway]] ===<br />
<br />
* [[VW Golf (1K) CAN-Gateway#Coding|Coding]]<br />
* [http://www.ross-tech.com/vag-com/download/label-files/1K0-907-530.lbl Label File]<br />
<br />
=== [25] - Immobilizer ===<br />
<br />
* Label File ''(1K0-920-xxx-25.LBL)''<br />
<br />
=== [37] - [[Audi Radio/Navigation System|Navigation]] ===<br />
<br />
* [[Audi Radio/Navigation System (RNS-E)|Radio/Navigation System (RNS-E)]]<br />
** [[Audi Radio/Navigation System (RNS-E)#Coding|Coding]]<br />
** [[Audi Radio/Navigation System (RNS-E)#Adaptation|Adaptation]]<br />
** Label File ''(8E0-035-192-RNSE.LBL)''<br />
<br />
=== [42] - Door Electronics Driver ===<br />
<br />
=== [46] - [[Audi R8 (42) Comfort System|Comfort System]] ===<br />
<br />
* [[Audi R8 (42) Comfort System#Coding|Coding]]<br />
* [[Audi R8 (42) Comfort System#Adaptation|Adaptation]]<br />
* [[Audi R8 (42) Comfort System#Special Procedures|Special Procedures]]<br />
* [http://www.ross-tech.com/vag-com/download/label-files/8J0-959-433.lbl Label File]<br />
<br />
=== [47] - [[Audi R8 (42) Sound System|Sound System]] ===<br />
<br />
* [[Audi R8 (42) Sound System#Coding|Coding]]<br />
* Label File ''(420-035-223.LBL)''<br />
<br />
=== [52] - Door Electronics Passenger ===<br />
=== [56] - [[Audi_Radio/Navigation_System|Radio (Analog)]] ===<br />
<br />
* [[Audi Radio/Navigation System (RNS-E)|Radio/Navigation System (RNS-E)]]<br />
** [[Audi Radio/Navigation System (RNS-E)#Coding|Coding]]<br />
** [[Audi Radio/Navigation System (RNS-E)#Adaptation|Adaptation]]<br />
** Label File ''(8E0-035-192-RNSE.LBL)''<br />
<br />
=== [61] - Battery Regulation ===<br />
<br />
* [[Battery_Replacement]] (This car uses address 61 then Adaptation channel 003)<br />
<br />
=== [65] - [[Audi R8 (42) Tire Pressure Monitoring System|Tire Pressure Monitoring System (TPMS)]] ===<br />
<br />
* [[Audi R8 (42) Tire Pressure Monitoring System#Coding|Coding]]<br />
* [[Audi R8 (42) Tire Pressure Monitoring System#Special Procedures|Special Procedures]]<br />
<br />
=== [76] - [[Audi R8 (42) Parking Aid|Parking Aid]] ===<br />
<br />
''For MY 2010+ see '''[10] - Parking Aid 2'''.''<br />
<br />
* [[Audi R8 (42) Parking Aid|Coding]]<br />
* [[Audi R8 (42) Parking Aid|Adaptation]]<br />
* Label File ''(8P0-919-283.LBL)''<br />
<br />
=== [77] - [[Audi R8 (42) Telephone Preparation|Telephone]] ===<br />
<br />
* [[Audi R8 (42) Telephone Preparation|Telephone Preparation]]<br />
** [[Audi R8 (42) Telephone Preparation#Coding|Coding]]<br />
** [[Audi R8 (42) Telephone Preparation#Adaptation|Adaptation]]<br />
** Label File ''(8P0-862-335.LBL)''<br />
<br />
=== [A6] - Belt Microphone ===<br />
<br />
__NOTOC__<br />
__NOEDITSECTION__</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Battery_Replacement&diff=8552
Battery Replacement
2018-05-10T14:14:16Z
<p>Andy: </p>
<hr />
<div>__FORCETOC__<br />
<br />
A large majority of modern VW/Audi/Seat/Skoda vehicles require the configuration of replacement batteries. The diagnostic steps vary depending on the actual vehicle configuration.<br />
<br />
'''<u>Prerequisites:</u>'''<br><br />
* New VW/Audi Battery Installed<br />
** Aftermarket batteries may NOT have a valid Part Number, Vendor code or Serial number. Ross-Tech cannot offer assistance if the necessary information is missing.<br />
* Key On, Engine OFF<br />
<br><br />
== 61-Battery Regulation using CAN ==<br />
This procedure applies to battery replacement in vehicles using a separate battery management control module.<br />
Address '''61: Battery Regul.''' Labels: 4F0-910-181.lbl<br />
Part No SW: 4F0 910 181 E HW: 4F0 915 181 A<br />
Component: ENERGIEMANAGER H12 0490 <br />
<br />
Subsystem 1 - Part No: 000 915 105 C<br />
Component: von VA0 2502160103 <br />
Coding: 303030393135313035432056413032353032313630313033<br />
Shop #: WSC 54332 321 22222<br />
=== Coding ===<br />
'''[Select]'''<br><br />
'''[61 - Battery Regulation]'''<br><br />
'''[Coding - 07]'''<br><br />
Use the pull down menu to select the battery (slave) listed as #1.<br><br />
'''[http://www.ross-tech.com/vcds/tour/recode_screen.html#battery [Battery Coding]]'''<br><br />
* Enter the new Battery Part Number (10 or 11 digits).<br />
* Enter the new Battery Serial Number (10 digits).<br />
* Select the new Battery Vendor.<br />
'''[OK]'''<br><br />
'''[Do it!]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
<br />
Your new Battery should now be coded and the Battery Control Module should be aware of the new Battery.<br><br />
<br />
=== Special Notes ===<br />
* Some vehicles like Audi R8 along with some rest-of-world models with Stop-Start, can have a 61 that is really a virtual module in the 19-CAN Gateway. In these cases, the new battery information is entered in 61-Battery Regulation then Adaptation Channel 004.<br />
<br />
----<br />
<br />
== 19-CAN Gateway using CAN ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address '''19: CAN Gateway (J533)''' Labels: 8T0-907-468.clb<br />
Part No SW: 8T0 907 468 Q HW: 8T0 907 468 L<br />
Component: GW-BEM 5CAN-M H10 0095 <br />
<br />
Subsystem 1 - Part No SW: 8K0 915 181 B HW: 8K0 915 181 B<br />
Component: '''J367-BDM''' H04 0150 <br />
=== Long Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long [Long Adaptation-0A]] function under 19-CAN-Gateway control module. Follow the on-screen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Long Adaptation-0A]'''<br><br />
Channel 004<br><br />
'''[Read]'''<br><br />
VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example:<br />
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ<br />
<br />
N = Battery Part Number (11 Digits)<br />
X = Battery Vendor (3 Digits)<br />
Z = Battery Serial Number (10 Digits)<br />
<br />
'''[Add to Log]''' ''Saving the original value to a log is strongly recommended''.<br><br />
Type the New Battery details into the '''New value''' field.<br><br />
* Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.<br />
'''[Test]''' <br><br />
'''[Save]'''<br><br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br />
=== Special Notes ===<br />
* Measuring Block groups 008, 019 and 020 should show Battery information.<br />
* Registered users encountering difficulty can contact us via [mailto:Support@Ross-Tech.com email] -or- join and post in [http://forums.ross-tech.com our forum]. Please include the Auto-Scan, Saved Adaptation Channel 004 Log prior to modifications, the part number, serial number and vendor code located on the original battery and the details located on the brand new battery in addition to the error message details.<br />
<font color=white>tinyurl.com/pzgolq7</font><br />
<br />
----<br />
<br />
== 19-CAN Gateway using (UDS/ODX) ==<br />
This procedure applies to battery replacement in vehicles using a battery management control module that is a slave/subsystem of the CAN Gateway.<br />
Address 19: '''CAN Gateway (J533)''' Labels: None<br />
Part No SW: 4G0 907 468 E HW: 4G0 907 468 A<br />
Component: J533--Gateway H08 0213 <br />
ASAM Dataset: EV_GatewUDS 001025<br />
<br />
'''Battery Monitoring Control Module''': <br />
Subsystem 1 - Part No SW: 8X0 915 181 HW: 8X0 915 181 <br />
Component: J367-BDM H07 0140 <br />
=== Adaptation ===<br />
Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html [Adaptation-10]] function under 19-CAN-Gateway control module. Use the drop-down menus to enter the Part Number, Vendor, and Serial Number information located on the new battery .<br><br />
<br><br />
'''[Select]'''<br><br />
'''[19 - CAN-Gateway]'''<br><br />
'''[Long Adaptation-0A]'''<br><br />
* '''Battery adaptation - Size'''<br />
** Select the battery Ah rating from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Manufacturer'''<br />
** Select the battery manufacturer from the drop-down menu followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
* '''Battery adaptation - Serial number'''<br />
** Type the serial number code from the replacement battery followed by '''[Do It!]''' and confirm '''[Yes]'''<br />
Providing the value was accepted by the controller the new battery coding is complete.<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
<br><br />
<br />
----<br />
<br />
== Example Picture ==<br />
'''Note''': The 10 digit serial number may be preceded by the Battery Vendor Code, for instance VA0. See examples below: <br />
{| class="wikitable" border="0" width="450"<br />
|-<br />
!colspan="14" style="background:white"| Click on thumbnail image to enlarge.<br />
|-<br />
| [[File:Battery serial number.jpg|200px|center|caption]]<br />
|-<br />
| If the code is VA0310314E04G then drop the VA0 and just enter 310314E04G as the Serial Number.<br />
|}<br />
<br><br />
== Video Link ==<br />
[[File:Wikibatterycoding.jpg|200px|link=http://www.youtube.com/watch?v=IJAScg6JrYI]]<br />
<br />
http://www.youtube.com/watch?v=IJAScg6JrYI<br />
== Notes ==<br />
* Users encountering difficulty with the data shown on the battery sticker may want to:<br />
** Consider scanning the QR code with a smart phone app. We have had success with BB, Android and iOS platform mobile devices running [http://www.i-nigma.com/Downloadi-nigmaReader.html i-nigma's free app.]<br><br />
** Refer to this [http://www.audizine.com/forum/showthread.php/581232-B8-A4-Battery-Replacement-Coding B8 A4 Battery Replacement - Coding] thread which discusses labels in some detail.<br />
** We have seen some cases where (contrary to established norms) some Varta batteries have VAO (letter O) instead of VA0 (number 0). If you encounter a problem with Coding one of these, please try substituting the letter for the number or vice versa.<br />
<br />
[[Category:Subsystems]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Working_on_the_Electro-Mechanical_Parking_Brake_(EPB)&diff=8535
Working on the Electro-Mechanical Parking Brake (EPB)
2018-04-04T12:48:43Z
<p>Andy: </p>
<hr />
<div>'''The following Tech Tip demonstrates the basic steps for working on the Electro-Mechanical Parking Brake (EPB) systems found in VW/Audi vehicles. This control module is accessed using address [53 - Parking Brake] electronics. (03-ABS for MQB platform cars).'''<br />
<br />
The specific procedures and Basic Setting groups for each vehicle are listed using the main [[Diagnostic Procedures]] page and choosing the proper Brand and Chassis type. Vehicles that typically use the EPB system include:<br />
<br />
* Audi<br />
** [[Audi A3/S3 (8V/FF)]] (MQB platform ABS)<br />
** [[Audi Q3 (8U/FS)]] (older cars have 53, newer cars use the [[VW_Golf_VII_(5G/AU)_ABS_Brakes]] instructions)<br />
** [[Audi A4/S4/RS4/Cabriolet (8K) | A4/S4/RS4/Cabriolet (8K)]]<br />
** [[Audi A5/S5 (8T) | A5/S5 (8T)]]<br />
** [[Audi Q5 (8R)]]<br />
** [[Audi A6/S6/RS6/allroad (4F) | A6/S6/RS6/Allroad (4F/FB)]]<br />
** [[Audi A6/S6/RS6/allroad (4G/FC) | A6 (4G/4H)]]<br />
** [[Audi A7 (4G) | A7 (4G)]]<br />
** [[Audi A8/S8 (4E) | A8/S8 (4E)]]<br />
** [[ Audi A8/S8 (4H) | A8/S8 (4H)]] ''(4H vehicles use the [[Audi A6 (4G/4H) Parking Brake]] procedure)''<br />
* Bentley<br />
** [[Bentley Continental (3W) | Continental (3W)]]<br />
* VW<br />
** [[VW Passat (3C) | Passat (3C/AN)]]<br />
** [[VW Passat CC (35) | Passat Coupe (35)]]<br />
** [[VW Tiguan (5N) | Tiguan (5N/AX)]]<br />
** [[VW Touareg (7P)]]<br />
** [[VW Golf VII (5G/AU)]] (Rest of World MQB platform ABS)<br />
<br />
<br />
<br />
<br />
----<br />
<br />
'''Replacing the brake pads on Electro-Mechanical Parking Brake (EPB) equipped vehicles consists of 4 main steps''':<br />
== Preparing the vehicle for the brake repairs ==<br />
<br />
* The EPB module is very sensitive to low voltage conditions! It is critical that a battery charger is properly connected and used for the duration of the rear brake job.<br />
** Vehicles with a battery mounted in the rear typically use a battery management module and it is essential to connect the charger properly at the charging posts as shown in this: [http://wiki.ross-tech.com/wiki/images/7/77/A8_charger_hookup.jpg Audi A8 (4E) example]<br />
* Verify that the EPB system is working properly prior to the repair. This includes but is not limited to applying the normal hydraulic brake pedal and operating the EPB switch and running a complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] prior to repairs.<br />
* Make sure the system is fully assembled prior to repairs! This includes the calipers properly installed on the rotors with pads and all electrical components being connected. <br />
* The Parking Brake must be OFF prior to repairs or Basic Settings will not be possible!<br />
<br />
== Open Rear Parking Brake ==<br />
* The EPB system must be put into a service mode prior to the calipers being removed from the vehicle so the pistons can be pushed into the caliper housing. The specific Basic Setting groups vary depending on the vehicle and repair procedure to be performed. <br />
<br />
* Using VCDS you will click '''[Select]''' > '''[53 - Parking Brake]''' > '''[Basic Settings - 04]''' and TYPE in the specific Group Number -or- Select the appropriate option from the drop-down menu. Refer to the specific '''[[Diagnostic Procedures]]''' page for the vehicle in question. Click '''[Go!]''' and the brake calipers will open for repairs.<br><br />
<br />
* It is important to wait 30 seconds after the brake calipers and live readings stop moving before clicking '''[Done, Go Back]''' > '''[Close Controller, Go Back - 06]''' and removing the key from Ignition Switch.<br />
<br />
* The caliper pistons do not move back into the caliper, they are in a internally released position that allows the technician to push the pistons in as you would do with a conventional front brake job.<br />
<br />
* Perform the brake repairs and reassemble the system prior to moving on to the next step.<br />
<br />
<br />
== Close Rear Parking Brake ==<br />
<br />
* The EPB system service mode must be deactivated after the repairs.<br />
<br />
* Using VCDS you will click '''[Select]''' > '''[53 - Parking Brake]''' > '''[Basic Settings - 04]''' and TYPE in the specific Group Number -or- Select the appropriate option from the drop-down menu. Refer to the specific '''[[Diagnostic Procedures]]''' page for the vehicle in question. Click '''[Go!]''' and the brake calipers will close after repairs.<br><br />
<br />
* It is important to wait 30 seconds after the brake calipers and live readings stop moving before clicking '''[Done, Go Back]''' > prior to moving on to the next step.<br />
<br />
<br />
== Function Test ==<br />
<br />
* When applicable the EPB must be cycled On and Off prior to the Function Test. Do so using the button inside the vehicle while applying the normal hydraulic brake pedal.<br />
<br />
* Using VCDS you will click '''[Select]''' > '''[53 - Parking Brake]''' > '''[Basic Settings - 04]''' and TYPE in the specific Group Number. Refer to the specific '''[[Diagnostic Procedures]]''' page for the vehicle in question. Click '''[Go!]''' and the brake calipers will open and close 3 times taking up the excessive gap in between the piston and backing plate of the new pads.<br><br />
<br />
* It is important to wait 30 seconds after the brake calipers and live readings stop moving before clicking '''[Done, Go Back]''' > and checking '''[Fault Codes - 02].'''<br><br />
<br />
* The Brake job should be complete and the system should not have any fault codes stored. <br />
** If faults are stored use the Search feature in the upper right hand corner of all Ross-Tech Wiki pages to see if we have a page specific to the code(s) in question.<br />
** If [[02596 | 02596 - Rear Brake Pads Worn]] is stored in the (4E) Audi A8 see the [[Audi A8 (4E) Parking Brake#Adaptation | Pad Thickness]] procedure.<br />
<br />
<br />
<br />
<br><br />
<br><br />
The original "Avoid Damaging Rear Calipers" Tech Tip First appeared in Motor Magazine, June 2008. ''Copyright © 2000-2010 by Ross-Tech LLC''. It is available in the downloadable .pdf format using this link to our [http://www.ross-tech.com/vag-com/advertising.html Advertising Page].<br />
<br />
<br />
== Video Link ==<br />
=== Electro-Mechanical Parking Brake (EPB), Rear Brake Service ===<br />
<br />
[[File:Image4.jpg|200px|link=http://www.youtube.com/watch?v=cHJMI4QkSy8]]<br />
<br />
http://www.youtube.com/watch?v=cHJMI4QkSy8<br />
<br />
<br />
__FORCETOC__<br />
[[Category:Tech Tips]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Working_on_the_Electro-Mechanical_Parking_Brake_(EPB)&diff=8534
Working on the Electro-Mechanical Parking Brake (EPB)
2018-04-04T12:47:17Z
<p>Andy: </p>
<hr />
<div>'''The following Tech Tip demonstrates the basic steps for working on the Electro-Mechanical Parking Brake (EPB) systems found in VW/Audi vehicles. This control module is accessed using address [53 - Parking Brake] electronics. (03-ABS for MQB platform cars).'''<br />
<br />
The specific procedures and Basic Setting groups for each vehicle are listed using the main [[Diagnostic Procedures]] page and choosing the proper Brand and Chassis type. Vehicles that typically use the EPB system include:<br />
<br />
* Audi<br />
** [[Audi A3/S3 (8V/FF)]] (MQB platform ABS)<br />
** [[Audi Q3 (8U/FS)]] (older cars have 53, newer cars use 03 for EPB)<br />
** [[Audi A4/S4/RS4/Cabriolet (8K) | A4/S4/RS4/Cabriolet (8K)]]<br />
** [[Audi A5/S5 (8T) | A5/S5 (8T)]]<br />
** [[Audi Q5 (8R)]]<br />
** [[Audi A6/S6/RS6/allroad (4F) | A6/S6/RS6/Allroad (4F/FB)]]<br />
** [[Audi A6/S6/RS6/allroad (4G/FC) | A6 (4G/4H)]]<br />
** [[Audi A7 (4G) | A7 (4G)]]<br />
** [[Audi A8/S8 (4E) | A8/S8 (4E)]]<br />
** [[ Audi A8/S8 (4H) | A8/S8 (4H)]] ''(4H vehicles use the [[Audi A6 (4G/4H) Parking Brake]] procedure)''<br />
* Bentley<br />
** [[Bentley Continental (3W) | Continental (3W)]]<br />
* VW<br />
** [[VW Passat (3C) | Passat (3C/AN)]]<br />
** [[VW Passat CC (35) | Passat Coupe (35)]]<br />
** [[VW Tiguan (5N) | Tiguan (5N/AX)]]<br />
** [[VW Touareg (7P)]]<br />
** [[VW Golf VII (5G/AU)]] (Rest of World MQB platform ABS)<br />
<br />
<br />
<br />
<br />
----<br />
<br />
'''Replacing the brake pads on Electro-Mechanical Parking Brake (EPB) equipped vehicles consists of 4 main steps''':<br />
== Preparing the vehicle for the brake repairs ==<br />
<br />
* The EPB module is very sensitive to low voltage conditions! It is critical that a battery charger is properly connected and used for the duration of the rear brake job.<br />
** Vehicles with a battery mounted in the rear typically use a battery management module and it is essential to connect the charger properly at the charging posts as shown in this: [http://wiki.ross-tech.com/wiki/images/7/77/A8_charger_hookup.jpg Audi A8 (4E) example]<br />
* Verify that the EPB system is working properly prior to the repair. This includes but is not limited to applying the normal hydraulic brake pedal and operating the EPB switch and running a complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto-Scan] prior to repairs.<br />
* Make sure the system is fully assembled prior to repairs! This includes the calipers properly installed on the rotors with pads and all electrical components being connected. <br />
* The Parking Brake must be OFF prior to repairs or Basic Settings will not be possible!<br />
<br />
== Open Rear Parking Brake ==<br />
* The EPB system must be put into a service mode prior to the calipers being removed from the vehicle so the pistons can be pushed into the caliper housing. The specific Basic Setting groups vary depending on the vehicle and repair procedure to be performed. <br />
<br />
* Using VCDS you will click '''[Select]''' > '''[53 - Parking Brake]''' > '''[Basic Settings - 04]''' and TYPE in the specific Group Number -or- Select the appropriate option from the drop-down menu. Refer to the specific '''[[Diagnostic Procedures]]''' page for the vehicle in question. Click '''[Go!]''' and the brake calipers will open for repairs.<br><br />
<br />
* It is important to wait 30 seconds after the brake calipers and live readings stop moving before clicking '''[Done, Go Back]''' > '''[Close Controller, Go Back - 06]''' and removing the key from Ignition Switch.<br />
<br />
* The caliper pistons do not move back into the caliper, they are in a internally released position that allows the technician to push the pistons in as you would do with a conventional front brake job.<br />
<br />
* Perform the brake repairs and reassemble the system prior to moving on to the next step.<br />
<br />
<br />
== Close Rear Parking Brake ==<br />
<br />
* The EPB system service mode must be deactivated after the repairs.<br />
<br />
* Using VCDS you will click '''[Select]''' > '''[53 - Parking Brake]''' > '''[Basic Settings - 04]''' and TYPE in the specific Group Number -or- Select the appropriate option from the drop-down menu. Refer to the specific '''[[Diagnostic Procedures]]''' page for the vehicle in question. Click '''[Go!]''' and the brake calipers will close after repairs.<br><br />
<br />
* It is important to wait 30 seconds after the brake calipers and live readings stop moving before clicking '''[Done, Go Back]''' > prior to moving on to the next step.<br />
<br />
<br />
== Function Test ==<br />
<br />
* When applicable the EPB must be cycled On and Off prior to the Function Test. Do so using the button inside the vehicle while applying the normal hydraulic brake pedal.<br />
<br />
* Using VCDS you will click '''[Select]''' > '''[53 - Parking Brake]''' > '''[Basic Settings - 04]''' and TYPE in the specific Group Number. Refer to the specific '''[[Diagnostic Procedures]]''' page for the vehicle in question. Click '''[Go!]''' and the brake calipers will open and close 3 times taking up the excessive gap in between the piston and backing plate of the new pads.<br><br />
<br />
* It is important to wait 30 seconds after the brake calipers and live readings stop moving before clicking '''[Done, Go Back]''' > and checking '''[Fault Codes - 02].'''<br><br />
<br />
* The Brake job should be complete and the system should not have any fault codes stored. <br />
** If faults are stored use the Search feature in the upper right hand corner of all Ross-Tech Wiki pages to see if we have a page specific to the code(s) in question.<br />
** If [[02596 | 02596 - Rear Brake Pads Worn]] is stored in the (4E) Audi A8 see the [[Audi A8 (4E) Parking Brake#Adaptation | Pad Thickness]] procedure.<br />
<br />
<br />
<br />
<br><br />
<br><br />
The original "Avoid Damaging Rear Calipers" Tech Tip First appeared in Motor Magazine, June 2008. ''Copyright © 2000-2010 by Ross-Tech LLC''. It is available in the downloadable .pdf format using this link to our [http://www.ross-tech.com/vag-com/advertising.html Advertising Page].<br />
<br />
<br />
== Video Link ==<br />
=== Electro-Mechanical Parking Brake (EPB), Rear Brake Service ===<br />
<br />
[[File:Image4.jpg|200px|link=http://www.youtube.com/watch?v=cHJMI4QkSy8]]<br />
<br />
http://www.youtube.com/watch?v=cHJMI4QkSy8<br />
<br />
<br />
__FORCETOC__<br />
[[Category:Tech Tips]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=VW_Golf_VII_(5G/AU)_ABS_Brakes&diff=8505
VW Golf VII (5G/AU) ABS Brakes
2018-02-27T21:57:45Z
<p>Andy: </p>
<hr />
<div>== Basic Setting ==<br />
=== Caution! ===<br />
* Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors. <br />
* Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.<br />
* It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults! There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door.<br />
<br />
=== Open Rear Parking Brake ===<br />
'''<u>Prerequisites:</u>'''<br><br />
* Connect a battery charger as per repair manual.<br />
* Cycle the Parking Brake ON, then OFF first.<br />
'''[Select]'''<br><br />
'''[03 - ABS Brakes]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Select '''Start lining change mode'''''<br><br />
'''[Go!]''' to activate the Basic Setting.<br><br />
The brake calipers will then open, allowing the pads to be changed.<br><br />
You should hear the rear caliper motors operating. <br><br />
Wait 30 seconds after it says '''Not Running''' or the noises have stopped before clicking '''[Stop]'''<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br />
* Turn ignition off and leave battery charger connected.<br><br />
<br />
''The caliper pistons do not move back into the caliper, they must be pushed in using a hand tool. Fault code [[721152 | 721152 - Brake pad replacement mode active]] will be stored, this is normal.''<br />
<br />
=== Close Rear Parking Brake ===<br />
'''<u>Prerequisites:</u>'''<br><br />
* Connect a battery charger as per repair manual.<br />
'''[Select]'''<br><br />
'''[03 - ABS Brakes]'''<br><br />
'''[Basic Settings - 04]'''<br><br />
Select '''End lining change mode'''''<br><br />
'''[Go!]''' to activate the Basic Setting.<br><br />
The brake calipers will then close.<br><br />
Wait 30 seconds after it says '''Not Running''' or the noises have stopped before clicking '''[Stop]'''<br><br />
'''[Done, Go Back]'''<br><br />
'''[Close Controller, Go Back - 06]'''<br><br />
* Turn ignition off<br><br />
<br />
The LED in the parking brake switch and the warning lamp in the instrument cluster will probably continue to blink rapidly in addition to Fault code [[C1011 | C1011 - Brake pad replacement mode active]]. This should stop after cycling the Parking Brake ON, then OFF again using the switch in the vehicle while holding the brake pedal AFTER all rear brake components are reassembled.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Control_Module_Maps&diff=8494
Control Module Maps
2018-02-08T21:12:31Z
<p>Andy: /* Special Notes */</p>
<hr />
<div>__FORCETOC__<br />
== What is a Control Module Map? ==<br />
<br />
VCDS supports "Control Module Maps", this function rapidly scans through all possible measuring block groups and/or adaptation channels on any ECU and writes a "map" file. These "map" files are useful for creating new label files or taking a "snapshot" of all available data from an ECU.<br />
<br />
* *.PLA files are Adaptation Maps.<br />
* *.PLB files are Meas. Block Maps<br />
<br />
[http://www.ross-tech.com/vcds/tour/controller-channels-map.html VCDS Manual: Control Module Maps]<br />
<br />
==== Special Notes ====<br />
<br />
* Control modules using the newest UDS/ODX protocol require a special .ROD file for VCDS to interpret data and they do not support traditional Measuring Blocks or Adaptation channel numbers. Since no data is readable without a .ROD file, there is no way for VCDS to interrogate all possible Measuring Blocks or Adaptation Values if those aren't already documented. In other words, the Controller Channels Map function does not work with control modules using the UDS/ODX protocol if no ROD file is present. If you run a Debug Level: 2 as described below, any control modules using UDS will be skipped and PLA/PLB files will not be retrieved if no ROD file is present. Current interfaces are able to create channel maps of Adaptation and Advanced Measuring Values, again only if an appropriate ROD file is present.<br />
<br />
== How can I help? ==<br />
<br />
We are continuously working on improving this wiki and the VCDS label files, therefore it's very helpful to have maps from modules which are either new, undocumented or incomplete yet. You can help us by providing such maps from your car(s). After creating the "map" files (file type/ending PLB, PLA and CSV), you can find them in the ''/VCDS/Logs/'' folder - please send them to us via [mailto:Support@Ross-Tech.com email]. If you are sending files, please attach an Auto-Scan from the car(s) you obtained the maps from too.<br />
<br />
There are two ways how you can create such maps, if you are unsure about this procedure we recommend the first variant.<br />
<br />
'''''Type #1''''': To create a map from all undocumented control modules in the car, please perform the following procedure:<br />
<br />
'''[Options]'''<br><br />
Debug Level: 2<br><br />
'''[Apply]'''<br><br />
'''[Auto-Scan]'''<br><br />
Select Chassis Type<br><br />
'''[Start]'''<br><br />
<br />
VCDS will now automatically create pre-label files from all undocumented control modules, once it's finished you will find these "map" files (file type/ending PLB, PLA and CSV) in the ''/VCDS/Logs/'' folder. Please send these to us via [mailto:Support@Ross-Tech.com email] and make sure to attach an Auto-Scan from the car(s) you obtained the maps from as well. ''Please note that do to the amount of requests coming in we cannot respond to all emails (and sent out confirmations or status updates) but your files will added to the queue and we'll try to get the relating label files done as soon as possible.''<br />
<br />
<br />
'''''Type #2''''': To create map files from individual control modules, please perform the following procedure:<br />
<br />
'''[Applications]'''<br><br />
'''[Controller Channels Map]'''<br><br />
Address: XX ''(Enter the address of the control module in question, e.g. 01 for engine)''<br><br />
Function: Meas. Blocks/Adaptation<br><br />
Output: Pre-Label File<br><br />
'''[Start]'''<br><br />
<br />
VCDS will now create pre-label files from the module you chose, once it's finished you will find this "map" file (file type/ending PLB, PLA and CSV) in the ''/VCDS/Logs/'' folder. Please send these to us via [mailto:Support@Ross-Tech.com email] and make sure to attach an Auto-Scan from the car(s) you obtained the maps from as well.''Please note that do to the amount of requests coming in we cannot respond to all emails (and sent out confirmations or status updates) but your files will added to the queue and we'll try to get the relating label files done as soon as possible.''<br />
<br />
<br />
== How do I find out if the control modules in my car are documented? ==<br />
<br />
Start VC and perform a standard Auto-Scan:<br />
<br />
'''[Auto-Scan]'''<br><br />
Select your model.<br><br />
'''[Start]'''<br><br><br />
After the Auto-Scan is finished, you will see outputs like this:<br />
<br />
Address 01: Engine Labels: 06A-906-033-BGU.LBL<br />
Part No: 06A 906 033 CM<br />
Component: SIMOS71 1.6l 2VG 6395<br />
Coding: 0000075<br />
Shop #: WSC 12345<br />
<br />
'''OR'''<br><br />
<br />
Address 76: Park Assist Labels: None<br />
Part No: 1Z0 919 283 B<br />
Component: Parkhilfe 4-Kan H04 0020<br />
Coding: 0001001<br />
Shop #: WSC 12345<br />
<br />
When you see ''Labels: None'' or ''Labels: Redir. Failed", there is no Label File for this control module.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=16452/P0068/000104&diff=8481
16452/P0068/000104
2017-12-14T21:20:47Z
<p>Andy: /* Possible Causes */</p>
<hr />
<div>__FORCETOC__<br />
== 16452/P0068/000104 - MAP/MAF <-> Throttle Position Correlation ==<br />
<br />
==== Possible Symptoms ====<br />
<br />
* Malfunction Indicator Lamp (MIL) active<br />
<br />
==== Possible Causes ====<br />
<br />
* Mass Air Flow Sensor (G70/MAF) or Intake Manifold Pressure Sensor (G71/MAP) faulty<br />
* Dirty or faulty throttle body.<br />
* Vacuum leak.<br />
<br />
==== Possible Solutions ====<br />
<br />
* Check Mass Air Flow Sensor (G70/MAF) or Intake Manifold Pressure Sensor (G71/MAP)<br />
* Clean Throttle Body and perform [[Throttle Body Alignment (TBA)]].<br />
* Check intake system for leaks and un-metered air.<br />
** This includes Intake Manifold Runner(s) and Intake Manifold Runner position sensor(s) when applicable.<br />
<br />
[[Category:Fault Codes]]</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Functions&diff=8441
Functions
2017-10-09T16:24:55Z
<p>Andy: </p>
<hr />
<div><table align="center" width="100%" style="background:#eaeaea;"><br />
<caption style="color:black;text-align: center; font-size: 24px; font-weight: bold; padding-bottom: 3px;">Function Chart</caption><br />
<br><br />
This chart shows the functions currently supported by each of our software products, as compared to the factory scan tools. Keep in mind that not all controllers in all cars will support all functions so please refer to the Factory Repair Manual for each vehicle to determine what should be supported. Also some functions (such as Advanced Measuring Values) may only work with supporting documentation which may not be exist for some modules at the present time. Some UDS functions require supporting documentation for VCDS-Mobile that requires a cloud connection at least once. Click on each of the links in the chart for more information including known limitations.<br />
<tr><br />
<br><br />
<br><br />
<td width="40%" align="center" style="color:green; background:silver; border: none;font-size: 14px;" height="30px" >'''VAS/ODIS '''</td> <br />
<td width="20%" align="center" style="color:brown; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds-lite/download/index.html VCDS-Lite Shareware]'''<br />
</td> <br />
<td width="20%" align="center" style="color:navy; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds/download/current.html VCDS Full Version] <br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds-mobile/ VCDS-Mobile]<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="center" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >'''$?-$15k <br> <br />
Factory scan tools<br>Function Number / Name'''</td> <br />
<td style="color:brown" "font-size: 14px;" width="20%" height="40px" align="center">[http://store.ross-tech.com/shop/VCDSLiteReg.html $0 - $99]<br> [http://ross-tech.com/vag-com/faq_3.html#3.3 Non-dongle/3rd Party Interfaces]<br />
</td> <br />
<td style="color:navy" "font-size: 14px;" width="20%" height="40px" align="center">'''<br />
[http://store.ross-tech.com/shop/cat/VCDS.html $199 - $699]'''<br><br />
[http://www.ross-tech.com/vcds/hex-v2.php HEX-V2] or [http://www.ross-tech.com/hex-net/ HEX-NET]</td> <br />
<td style="color:teal" "font-size: 14px;" width="20%" height="40px" align="center">'''<br />
[http://forums.ross-tech.com/forumdisplay.php?8-HEX-NET-Beta-Support STILL IN BETA TESTING]'''<br><br />
<br><br />
[http://www.ross-tech.com/hex-net/ HEX-NET]<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="center" style="color:green; background:silver; border: none;font-size: 14px;" height="30px" >'''Platform</td> <br />
<td width="20%" align="center" style="color:brown; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]'''<br />
</td> <br />
<td width="20%" align="center" style="color:navy; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]'''<br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]<br />
or <br />
'''[http://www.ross-tech.com/vcds-mobile/ Smart Devices]'''<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="left" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >00 AutoScan </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/autoscan.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/autoscan.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >01 Control Unit Info</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/open.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/open_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >02 Read Fault Codes</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Limited unless Registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >03 Output Tests </td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/output.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/out_test.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" > Selective Output Tests</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/out_test.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >04 Basic Settings</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/basic.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/b-settings.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >05 Clear Fault Codes </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >06 Close Controller</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/select.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/scm_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >07 Code Module</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/coding.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/recode_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" > Code Slave Modules</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/recode_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >08 Measuring Blocks</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/measblocks.html Limited unless Registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/m-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes, via<br><br />
Advanced Measuring Values</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Advanced Measuring Values</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/adv-meas-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >09 Single Reading</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/single.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/single_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >10 Adaptation</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/adaptation.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/adaptation_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >11 Login / Coding II </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/login.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/login_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >15 View Readiness</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Guided Readiness Scripts</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >16 Security Access</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/login.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/securityaccess.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >18 Supported Codes</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/supported-codes.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >33 Generic OBD-II</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/obd-2.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >18 Freeze-Frame Data</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Dual K-Line Support</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/interfaces.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >7-Digit PINs (VAS only)</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/pinskc.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/pin-skc.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Code Database Up to Date</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">Current through ~2006</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Diagnostics via CAN</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/canbus.html Yes <br> (with CAN Interface)]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Transport Mode</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/transport-mode.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Support for Dual ECUs</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Data Logging</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/datalogging.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/logging.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >HighSpeed DataLogging<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/m-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Real-Time Graphs<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Real-Time Gauges<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Graphic TDI Timing Checker<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/TDIGraph.html Registered Version Only]<br><br />
Not for V6 TDI</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/TDIGraph.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Control Module Finder<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/finder.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/module_finder.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Automated Service Reset (SRI)</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/sri-reset.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >ECU Mileage Checker<br><br />
<span style="font-size: 11px">(Many EDC-15/16 ECUs)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/EDC-15-Mileage.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Controller Channel Maps</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/controller-channels-map.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Wireless Connection via WiFi</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
with HEX-NET</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Installation List</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/installation-list.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >LT3/Crafter Support</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/LT3.php Yes]<br><br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
</table><br />
<br />
"Planned" = We plan to add this function but it is not currently available. <br><br />
"TBD" = To Be Determined, since we are still evaluating the incorporation of this function.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Functions&diff=8440
Functions
2017-10-09T16:23:30Z
<p>Andy: </p>
<hr />
<div><table align="center" width="100%" style="background:#eaeaea;"><br />
<caption style="color:black;text-align: center; font-size: 24px; font-weight: bold; padding-bottom: 3px;">Function Chart</caption><br />
<br><br />
This chart shows the functions currently supported by each of our software products, as compared to the factory scan tools. Keep in mind that not all controllers in all cars will support all functions so please refer to the Factory Repair Manual for each vehicle to determine what should be supported. Also some functions (such as Advanced Measuring Values) may only work with supporting documentation which may not be exist for some modules at the present time. Some UDS functions require supporting documentation for VCDS-Mobile that requires a cloud connection at least once. Click on each of the links in the chart for more information including known limitations.<br />
<tr><br />
<br><br />
<br><br />
<td width="40%" align="center" style="color:green; background:silver; border: none;font-size: 14px;" height="30px" >'''VAS/ODIS '''</td> <br />
<td width="20%" align="center" style="color:brown; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds-lite/download/index.html VCDS-Lite Shareware]'''<br />
</td> <br />
<td width="20%" align="center" style="color:navy; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds/download/current.html VCDS Full Version] <br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds-mobile/ VCDS-Mobile]<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="center" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >'''$?-$15k <br> <br />
Factory scan tools<br>Function Number / Name'''</td> <br />
<td style="color:brown" "font-size: 14px;" width="20%" height="40px" align="center">[http://store.ross-tech.com/shop/VCDSLiteReg.html $0 - $99]<br> [http://ross-tech.com/vag-com/faq_3.html#3.3 Non-dongle/3rd Party Interfaces]<br />
</td> <br />
<td style="color:navy" "font-size: 14px;" width="20%" height="40px" align="center">'''<br />
[http://store.ross-tech.com/shop/cat/VCDS.html $199 - $699]'''<br><br />
[http://www.ross-tech.com/vcds/hex-v2.php HEX-V2] or [http://www.ross-tech.com/hex-net/ HEX-NET]</td> <br />
<td style="color:teal" "font-size: 14px;" width="20%" height="40px" align="center">'''<br />
[http://forums.ross-tech.com/forumdisplay.php?8-HEX-NET-Beta-Support STILL IN BETA TESTING]'''<br><br />
<br><br />
[http://www.ross-tech.com/hex-net/ HEX-NET]<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="center" style="color:green; background:silver; border: none;font-size: 14px;" height="30px" >'''Platform</td> <br />
<td width="20%" align="center" style="color:brown; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]'''<br />
</td> <br />
<td width="20%" align="center" style="color:navy; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]'''<br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]<br />
or <br />
'''[http://www.ross-tech.com/vcds-mobile/ Smart Devices]'''<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="left" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >00 AutoScan (VAS 1001.01 )</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/autoscan.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/autoscan.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >01 Control Unit Info</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/open.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/open_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >02 Read Fault Codes</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Limited unless Registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >03 Output Tests </td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/output.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/out_test.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" > Selective Output Tests</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/out_test.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >04 Basic Settings</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/basic.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/b-settings.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >05 Clear Fault Codes </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >06 Close Controller</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/select.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/scm_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >07 Code Module</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/coding.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/recode_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" > Code Slave Modules</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/recode_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >08 Measuring Blocks</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/measblocks.html Limited unless Registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/m-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes, via<br><br />
Advanced Measuring Values</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Advanced Measuring Values</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/adv-meas-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >09 Single Reading</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/single.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/single_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >10 Adaptation</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/adaptation.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/adaptation_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >11 Login / Coding II </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/login.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/login_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >15 View Readiness</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Guided Readiness Scripts</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >16 Security Access</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/login.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/securityaccess.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >18 Supported Codes</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/supported-codes.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >33 Generic OBD-II</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/obd-2.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >18 Freeze-Frame Data</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Dual K-Line Support</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/interfaces.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >7-Digit PINs (VAS only)</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/pinskc.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/pin-skc.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Code Database Up to Date</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">Current through ~2006</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Diagnostics via CAN</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/canbus.html Yes <br> (with CAN Interface)]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Transport Mode</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/transport-mode.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Support for Dual ECUs</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Data Logging</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/datalogging.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/logging.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >HighSpeed DataLogging<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/m-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Real-Time Graphs<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Real-Time Gauges<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Graphic TDI Timing Checker<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/TDIGraph.html Registered Version Only]<br><br />
Not for V6 TDI</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/TDIGraph.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Control Module Finder<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/finder.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/module_finder.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Automated Service Reset (SRI)</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/sri-reset.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >ECU Mileage Checker<br><br />
<span style="font-size: 11px">(Many EDC-15/16 ECUs)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/EDC-15-Mileage.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Controller Channel Maps</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/controller-channels-map.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Wireless Connection via WiFi</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
with HEX-NET</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Installation List</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/installation-list.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >LT3/Crafter Support</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/LT3.php Yes]<br><br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
</table><br />
<br />
"Planned" = We plan to add this function but it is not currently available. <br><br />
"TBD" = To Be Determined, since we are still evaluating the incorporation of this function.</div>
Andy
https://wiki.ross-tech.com/wiki/index.php?title=Functions&diff=8397
Functions
2017-07-31T16:29:43Z
<p>Andy: </p>
<hr />
<div><table align="center" width="100%" style="background:#eaeaea;"><br />
<caption style="color:black;text-align: center; font-size: 24px; font-weight: bold; padding-bottom: 3px;">Function Chart</caption><br />
<br><br />
This chart shows the functions currently supported by each of our software products, as compared to the factory scan tools. Keep in mind that not all controllers in all cars will support all functions so please refer to the Factory Repair Manual for each vehicle to determine what should be supported. Also some functions (such as Advanced Measuring Values) may only work with supporting documentation which may not be exist for some modules at the present time. Some UDS functions require supporting documentation for VCDS-Mobile that requires a cloud connection at least once. Click on each of the links in the chart for more information including known limitations.<br />
<tr><br />
<br><br />
<br><br />
<td width="40%" align="center" style="color:green; background:silver; border: none;font-size: 14px;" height="30px" >'''VAS/ODIS '''</td> <br />
<td width="20%" align="center" style="color:brown; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds-lite/download/index.html VCDS-Lite Shareware]'''<br />
</td> <br />
<td width="20%" align="center" style="color:navy; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds/download/current.html VCDS Full Version] <br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vcds-mobile/ VCDS-Mobile]<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="center" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >'''$?-$15k <br> <br />
Factory scan tools<br>Function Number / Name'''</td> <br />
<td style="color:brown" "font-size: 14px;" width="20%" height="40px" align="center">[http://store.ross-tech.com/shop/VCDSLiteReg.html $0 - $99]<br> [http://ross-tech.com/vag-com/faq_3.html#3.3 Non-dongle/3rd Party Interfaces]<br />
</td> <br />
<td style="color:navy" "font-size: 14px;" width="20%" height="40px" align="center">'''<br />
[http://store.ross-tech.com/shop/cat/VCDS.html $199 - $699]'''<br><br />
[http://www.ross-tech.com/vcds/hex-v2.php HEX-V2] or [http://www.ross-tech.com/hex-net/ HEX-NET]</td> <br />
<td style="color:teal" "font-size: 14px;" width="20%" height="40px" align="center">'''<br />
[http://forums.ross-tech.com/forumdisplay.php?8-HEX-NET-Beta-Support STILL IN BETA TESTING]'''<br><br />
<br><br />
[http://www.ross-tech.com/hex-net/ HEX-NET]<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="center" style="color:green; background:silver; border: none;font-size: 14px;" height="30px" >'''Platform</td> <br />
<td width="20%" align="center" style="color:brown; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]'''<br />
</td> <br />
<td width="20%" align="center" style="color:navy; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]'''<br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:silver; border: none;font-size: 14px;" height="30px" >'''[http://www.ross-tech.com/vag-com/faq_1.html#1.4 Windows PC]<br />
or <br />
'''[http://www.ross-tech.com/vcds-mobile/ Smart Devices]'''<br />
</td><br />
</tr><br />
<tr> <br />
<td width="40%" align="left" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >00 AutoScan</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/autoscan.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/autoscan.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >01 Control Unit Info</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/open.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/open_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >02 Read Fault Codes</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Limited unless Registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >03 Output Tests </td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/output.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/out_test.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" > Selective Output Tests</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/out_test.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >04 Basic Settings</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/basic.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/b-settings.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >05 Clear Fault Codes </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >06 Close Controller</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/select.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/scm_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >07 Code Module</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/coding.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/recode_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" > Code Slave Modules</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/recode_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >08 Measuring Blocks</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/measblocks.html Limited unless Registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/m-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes, via<br><br />
Advanced Measuring Values</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Advanced Measuring Values</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/adv-meas-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >09 Single Reading</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/single.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/single_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >10 Adaptation</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/adaptation.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/adaptation_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >11 Login / Coding II </td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/login.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/login_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >15 View Readiness</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Guided Readiness Scripts</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/readiness.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >16 Security Access</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/login.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/securityaccess.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes<br><br />
via Cloud</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >18 Supported Codes</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/supported-codes.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >33 Generic OBD-II</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/obd-2.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >18 Freeze-Frame Data</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/dtc.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/dtc_screen.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Dual K-Line Support</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/interfaces.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >7-Digit PINs (VAS only)</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/pinskc.html Registered Version Only]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/pin-skc.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Code Database Up to Date</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">Current through ~2006</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Diagnostics via CAN</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/canbus.html Yes <br> (with CAN Interface)]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Transport Mode</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/transport-mode.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Support for Dual ECUs</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Data Logging</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/datalogging.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/logging.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >HighSpeed DataLogging<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/m-blocks.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Real-Time Graphs<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Real-Time Gauges<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Limited unless registered]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/index.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Graphic TDI Timing Checker<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/TDIGraph.html Registered Version Only]<br><br />
Not for V6 TDI</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vag-scope/TDIGraph.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Control Module Finder<br><br />
<span style="font-size: 11px">(Factory tools cannot do this!)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds-lite/manual/finder.html Yes]</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/module_finder.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Automated Service Reset (SRI)</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/sri-reset.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >ECU Mileage Checker<br><br />
<span style="font-size: 11px">(Many EDC-15/16 ECUs)</span></td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/EDC-15-Mileage.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Controller Channel Maps</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/controller-channels-map.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">TBD</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >Wireless Connection via WiFi</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes<br><br />
with HEX-NET</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Yes</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#eaeaea; border: none;font-size: 14px;" height="30px" >Installation List</td> <br />
<td width="20%" align="center" style="color:brown; background:#eaeaea; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#eaeaea; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/installation-list.html Yes]</td> <br />
<td width="20%" align="center" style="color:teal; background:#eaeaea; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
<tr> <br />
<td width="40%" align="left"" style="color:green; background:#f7f7f7; border: none;font-size: 14px;" height="30px" >LT3/Crafter Support</td> <br />
<td width="20%" align="center" style="color:brown; background:#f7f7f7; border: none;font-size: 14px;" height="30px">No</td> <br />
<td width="20%" align="center" style="color:navy; background:#f7f7f7; border: none;font-size: 14px;" height="30px">[http://www.ross-tech.com/vcds/tour/LT3.php Yes]<br><br />
</td> <br />
<td width="20%" align="center" style="color:teal; background:#f7f7f7; border: none;font-size: 14px;" height="30px">Planned</td> <br />
</tr><br />
</table><br />
<br />
"Planned" = We plan to add this function but it is not currently available. <br><br />
"TBD" = To Be Determined, since we are still evaluating the incorporation of this function.</div>
Andy