4-Speed Automatic Transmission (01M) - Revision history

Andy: /* Special Notes */

2014-11-14T13:52:34Z

Special Notes

← Older revision		Revision as of 13:52, 14 November 2014
Line 44:		Line 44:
	==== Special Notes ====		==== Special Notes ====

	* It is normal for there to be no explicit instructions or changes on the screen when you do the above procedure. The transmission controller does not provide any feedback that it has been successfully performed. Checking the binary switching in measuring block group 001 field 4 should confirm a change when field 3 is between 95 - 100% pedal position.		* It is normal for there to be no explicit instructions or changes on the screen when you do the above procedure. The transmission controller does not provide any feedback that it has been successfully performed. Current versions of VCDS may display "Data for Group 000 Not Available" across the four fields. Checking the binary switching in measuring block group 001 field 4 should confirm a change when field 3 is between 95 - 100% pedal position.
	* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.		* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.
	* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.		* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.

Dana at 16:24, 19 April 2012

2012-04-19T16:24:54Z

← Older revision		Revision as of 16:24, 19 April 2012
Line 4:		Line 4:
	The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. <br>		The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. <br>

	'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry]. Additional information can be found in the [~~http://store.ross-tech.com/shop/cat/BCD.html~~ Official Factory Repair ~~Manual~~] and sources such as [http://www.bentleypublishers.com/volkswagen/technical-training/vw-4-speed-automatic-trans-ssp.html Bentley Publisher's SSP (Self-Study Program)] .<br>		'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry]. Additional information can be found in the [[Official Factory Repair Information]] and sources such as [http://www.bentleypublishers.com/volkswagen/technical-training/vw-4-speed-automatic-trans-ssp.html Bentley Publisher's SSP (Self-Study Program)] .<br>

Dana at 15:47, 16 November 2011

2011-11-16T15:47:17Z

@@ Line 49: / Line 49: @@
 * When the 01M transmission is installed in  a vehicle using the Drive-by-Wire (DBW) throttle system, the ECM (Engine Control Module) may support a Kick-Down Basic Settings as described here: [[Automatic Transmission Basic Settings#Kick-Down_Basic_Settings_in_ECM | Automatic Transmission Basic Settings]].
 <br>
 [[Category:Transmissions]]

Andy: /* Special Notes */

2011-09-29T18:42:55Z

Special Notes

← Older revision		Revision as of 18:42, 29 September 2011
Line 44:		Line 44:
	==== Special Notes ====		==== Special Notes ====

	* It is normal for there to be no explicit instructions or changes on the screen when you do the above procedure. The transmission controller does not provide any feedback that it has been successfully performed. Checking the binary switching in measuring block group 001 should confirm a change at 95 - 100% pedal position.		* It is normal for there to be no explicit instructions or changes on the screen when you do the above procedure. The transmission controller does not provide any feedback that it has been successfully performed. Checking the binary switching in measuring block group 001 field 4 should confirm a change when field 3 is between 95 - 100% pedal position.
	* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.		* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.
	* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.		* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.

Dana at 02:32, 25 August 2011

2011-08-25T02:32:23Z

← Older revision		Revision as of 02:32, 25 August 2011
Line 4:		Line 4:
	The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. <br>		The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. <br>

	'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry].<br>		'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry]. Additional information can be found in the [http://store.ross-tech.com/shop/cat/BCD.html Official Factory Repair Manual] and sources such as [http://www.bentleypublishers.com/volkswagen/technical-training/vw-4-speed-automatic-trans-ssp.html Bentley Publisher's SSP (Self-Study Program)] .<br>

Dana at 02:55, 6 August 2011

2011-08-06T02:55:52Z

← Older revision		Revision as of 02:55, 6 August 2011
Line 2:		Line 2:

	'''Information'''<br>		'''Information'''<br>
	The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. '''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry].<br>		The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. <br>

			'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry].<br>


Line 17:		Line 19:
	'''Common Settings''':		'''Common Settings''':
	*00000 = Factory Mode		*00000 = Factory Mode
	*00011 = ~~Econonmy~~/Touring Mode		*00011 = Economy/Touring Mode
	*00012 = Sport Mode		*00012 = Sport Mode

Line 44:		Line 46:
	* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.		* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.
	* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.		* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.
	* When the 01M transmission is installed ~~with~~ a ~~gasoline engine~~ using the Drive-by-Wire (DBW) throttle (~~i.e. no throttle cable~~) ~~the Engine~~ may ~~also~~ support a Kick-Down Basic Settings as described here: [~~http://www.ross~~-~~tech.com/vag-com/cars/autotrans.html~~ Automatic Transmission ~~Info~~]		* When the 01M transmission is installed in a vehicle using the Drive-by-Wire (DBW) throttle system, the ECM (Engine Control Module) may support a Kick-Down Basic Settings as described here: [[Automatic Transmission Basic Settings#Kick-Down_Basic_Settings_in_ECM \| Automatic Transmission Basic Settings]].
			<br>


	[[Category:Transmissions]]		[[Category:Transmissions]]

Dana at 15:47, 28 July 2011

2011-07-28T15:47:13Z

← Older revision		Revision as of 15:47, 28 July 2011
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__

			'''Information'''<br>
			The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW. '''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Volkswagen_01M_transmission Wikipedia entry].<br>


	== Coding ==		== Coding ==

Dana at 14:47, 28 July 2011

2011-07-28T14:47:49Z

← Older revision		Revision as of 14:47, 28 July 2011
Line 17:		Line 17:

	== Basic Setting ==		== Basic Setting ==

			'''<u>Prerequisites:</u>'''<br>
			* No fault codes in the Auto Trans.<br>
			* [[Throttle Body Alignment (TBA)]] performed successfully ''when applicable''<br>
			* Ignition on, engine off.<br>
			* Do not touch the accelerator pedal.<br>


			'''[Select]'''<br>
			'''[02 - Auto Trans]'''<br>
			'''[Basic Settings - 04]'''<br>
			Set Group to "000" <br>
			'''[Go!]'''<br>
			Press accelerator pedal all the way to the floor and hold for 3 to 5 seconds.<br>
			'''[Done, Go Back]'''<br>
			Release the accelerator pedal.<br>

			==== Special Notes ====

			* It is normal for there to be no explicit instructions or changes on the screen when you do the above procedure. The transmission controller does not provide any feedback that it has been successfully performed. Checking the binary switching in measuring block group 001 should confirm a change at 95 - 100% pedal position.
			* If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.
			* If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.
			* When the 01M transmission is installed with a gasoline engine using the Drive-by-Wire (DBW) throttle (i.e. no throttle cable) the Engine may also support a Kick-Down Basic Settings as described here: [http://www.ross-tech.com/vag-com/cars/autotrans.html Automatic Transmission Info]



	[[Category:Transmissions]]		[[Category:Transmissions]]

RtWiKiSyS0p at 12:40, 29 December 2006

2006-12-29T12:40:22Z

← Older revision		Revision as of 12:40, 29 December 2006
Line 14:		Line 14:
	*00011 = Econonmy/Touring Mode		*00011 = Econonmy/Touring Mode
	*00012 = Sport Mode		*00012 = Sport Mode


			== Basic Setting ==

	[[Category:Transmissions]]		[[Category:Transmissions]]

RtWiKiSyS0p at 23:09, 1 August 2006

2006-08-01T23:09:34Z

← Older revision		Revision as of 23:09, 1 August 2006
Line 8:		Line 8:
	**0 = Factory Mode (Adaptive Transmission Mode)		**0 = Factory Mode (Adaptive Transmission Mode)
	**1 = Force Economy Mode (lower Shift Points)		**1 = Force Economy Mode (lower Shift Points)
	**2 = Force Sport Mode (higher Shift Points)		**2 = Force Sport Mode (higher Shift Points)<br>

	'''Common Settings''':		'''Common Settings''':